Infiniti G20 (P11). Manual - part 114

 

  Index      Infiniti     Infiniti G20 (P11) - service repair manual 1999-2002 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  112  113  114  115   ..

 

 

Infiniti G20 (P11). Manual - part 114

 

 

SBR646

SBR868C

8.

Insert piston seal into groove on cylinder body.

9.

With piston boot fitted to piston, insert piston boot into groove
on cylinder body and fit piston by turning it clockwise with long
nose pilers, or suitable tool.

SBR027D

10. Fit toggle lever, return spring and cable guide.

SBR306E

11. Adjust the piston to the right angle as shown in the figure.

SBR307E

Installation

NCBR0043

CAUTION:

I

Refill with new brake fluid “DOT 3”.

I

Never reuse drained brake fluid.

1.

Install caliper assembly.

I

As shown in the figure, align the piston’s concave to the pad’s
convex, then install the cylinder body to the torque member.

2.

Install brake hose to caliper securely.

3.

Install all parts and secure all bolts.

4.

Bleed air. Refer to “Bleeding Brake System”, BR-8.

GI

MA

EM

LC

EC

FE

CL

MT

AT

AX

SU

ST

RS

BT

HA

SC

EL

IDX

REAR DISC BRAKE

Assembly (Cont’d)

BR-31

Components

NCBR0044

SBR325E

SBR897D

Removal and Installation

NCBR0045

1.

To remove parking brake cable, first remove center console.

2.

Disconnect warning switch connector.

3.

Remove bolts, slacken off and remove adjusting nut.

SBR025D

4.

Remove lock plate and disconnect cable.

PARKING BRAKE CONTROL

Components

BR-32

Inspection

NCBR0046

1.

Check control lever for wear or other damage. Replace if nec-
essary.

2.

Check wires for discontinuity or deterioration. Replace if nec-
essary.

3.

Check warning lamp and switch. Replace if necessary.

4.

Check parts at each connecting portion and, if found deformed
or damaged, replace.

SBR029D

Adjustment

NCBR0047

Pay attention to the following points after adjustment.
1)

There is no drag when control lever is being released.

2)

Be sure that toggle lever returns to stopper when parking brake
lever is released.

SBR042D

1.

Loosen parking brake cable.

2.

Depress brake pedal fully more than five times.

3.

Operate control lever 10 times or more with a full stroke [203.5
mm (8.01 in)].

4.

Adjust control lever by turning adjusting nut.

5.

Pull control lever with specified amount of force. Check lever
stroke and ensure smooth operation.

Number of notches:

6 - 7 [196 N (20 kg, 44 lb)]

6.

Bend warning lamp switch plate. Warning lamp should come
on when lever is pulled “A” notches. It should go off when the
lever is fully released.

Number of “A” notches: 1

GI

MA

EM

LC

EC

FE

CL

MT

AT

AX

SU

ST

RS

BT

HA

SC

EL

IDX

PARKING BRAKE CONTROL

Inspection

BR-33

Purpose

NCBR0082

The ABS consists of electronic and hydraulic components. It allows for control of braking force so that lock-
ing of the wheels can be avoided.
The ABS:
1) Ensures proper tracking performance through steering wheel operation.
2) Enables obstacles to be avoided through steering wheel operation.
3) Ensures vehicle stability by preventing flat spins.

ABS (Anti-Lock Brake System) Operation

NCBR0083

I

When the vehicle speed is less than 10 km/h (6 MPH) this system does not work.

I

The Anti-Lock Brake System (ABS) has self-test capabilities. The system turns on the ABS warning lamp
for 1 second after turning the ignition switch ON. The system performs another test the first time the vehicle
reaches 6 km/h (4 MPH). A mechanical noise may be heard as the ABS performs a self-test. This is a
normal part of the self-test feature. If a malfunction is found during this check, the ABS warning lamp will
come on.

I

During ABS operation, a mechanical noise may be heard. This is a normal condition.

ABS Hydraulic Circuit

NCBR0084

SBR984D

1.

Inlet solenoid valve

2.

Outlet solenoid valve

3.

Reservoir

4.

Pump

5.

Motor

6.

Inlet valve

7.

Outlet valve

8.

Bypass check valve

9.

Damper

DESCRIPTION

ABS

Purpose

BR-34

 

 

 

 

 

 

 

Content   ..  112  113  114  115   ..