Content .. 24 25 26 27 ..

Hyundai H350 (2016 year). Instruction - part 26

Maintenance

Aiming point

H1 : Height between the head light (Low beam) bulb center and ground

H2 : Height between the head light (High beam) the high beam bulb center and ground

H3 : Height between the fog light bulb center and ground

W1 : Distance between the two head light (Low beam) bulbs centers

W2 : Distance between the two head light (High beam) high beam bulbs centers.

W3 : Distance between the two fog light bulbs centers

OEU074055-A

Unit: mm (in)

Head light

Fog light

Vehicle condition

Without driver

960.5

(37.8)

942 (37)

1,488 (58.6)

1,274 (50.2)

456.5 (18)

1,480 (58.3)

Projection type

With driver

960.5

(37.8)

942 (37)

1,488 (58.6)

1,274 (50.2)

456.5 (18)

1,480 (58.3)

Without driver

948 (37.3)

944 (37.2)

1,540(60.2)

1,280 (50.4)

456.5 (18)

1,480 (58.3)

MFR type

With driver

948 (37.3)

944 (37.2)

1,540(60.2)

1,280 (50.4)

456.5 (18)

1,480 (58.3)

7-72

Head light low beam

■ Based on 10m screen

OMD051054L-1

1. Turn the low beam on without driver aboard.

2. The cut-off line should be projected in the cut-off line shown in the picture.

3. When aiming the low beam, vertical aiming should be adjusted after adjusting the horizontal aiming.

4. If head light leveling device is equipped, adjust the head light leveling device switch with 0 positions.

7-73

Maintenance

Front fog light

■ Based on 10m screen

OEU074055-B

1. Turn the front fog lamp on with the driver (75 kg) aboard.

2. The cut-off line should be projected in the allowable range (shaded region).

7-74

Side marker lamp

Rear combination light bulbs

CAUTION

replacement

BUS, VAN

• When prying with a flat-tip

screwdriver, wrap it with pro-

tective tape to prevent dam-

age.

• Put on gloves to protect your

hands.

OEU074073

1.To remove the lamp, pry the lamp

OEU074046

with a flat-tip screwdriver and push

it rearward.

1. Tail/stop light

2.Disconnect the wiring connector,

2. Tail/stop light

and remove the bulb by turning the

3. Turn signal light

bulb socket counterclockwise.

4. Back up light

3.To install the bulb, reverse the

removal procedure.

5. Rear fog light

7-75

Maintenance

7.Install the socket in the assembly

by aligning the tabs on the socket

with the slots in the assembly.

Push the socket into the assembly

and turn the socket clockwise.

8.Reinstall the light assembly to the

body of the vehicle.

OEU074051

OEU074053

1.Open the rear door.

4.Remove the socket from the

2.Loosen the light assembly retain-

assembly by turning the socket

ing screws with a cross-tip screw-

counter clockwise until the tabs on

driver.

the socket align with the slots on

the assembly.

3.Remove the rear combination light

assembly from the body of the

5.Remove the bulb from the socket

vehicle.

by pressing it in and rotating it

counter clockwise until the tabs on

the bulb align with the slots in the

socket. Pull the bulb out of the

socket.

6.Insert a new bulb by inserting it into

the socket and rotating it until it

locks into place.

7-76

VAN

OEU054021

OEU054022

2.Remove the cover by pressing the

3.To replace the rear combination

OEU054020

both sides of the cover.

light (stop/tail light, turn signal light

1.Disconnect the power cord from

or back-up light), take it out from

the bulb.

the bulb holder by turning it coun-

terclockwise.

(1) Turn Signal Light

(2) Stop/Tail Light

(3) Back-up Light

4.Install the new bulb.

7-77

Maintenance

High mounted stop light bulb

License plate light bulb

Interior light bulb replacement

replacement (if equipped)

■ Map lamp

OEU074031

■ Room lamp

OEU074052

OEU074054

If the light does not operate, we rec-

1.Remove the lens by pressing the

ommend that the system be checked

tabs.

by an authorized HYUNDAI dealer.

2.Remove the socket from the lens.

3.Remove the bulb by pulling it

straight out.

4.Install a new bulb in the socket and

install the socket to the lens.

OEU074032

5.Reinstall the lens securely.

1.Using a flat-blade screwdriver,

gently pry the lens from the interior

light housing.

2.Remove the bulb by pulling it

straight out.

7-78

APPEARANCE CARE

Exterior care

Finish maintenance

WARNING

Washing

Exterior general caution

Prior to working on the Interior

To help protect your vehicle’s finish

It is very important to follow the label

Lights, ensure that the “OFF”

from rust and deterioration, wash it

directions when using any chemical

button is depressed to avoid

thoroughly and frequently at least

cleaner or polish. Read all warning

burning your fingers or receiv-

once a month with lukewarm or cold

and caution statements that appear

ing an electric shock.

water.

on the label.

If you use your vehicle for off-road

driving, you should wash it after each

3.Install a new bulb in the socket.

off-road trip. Pay special attention to

4.Align the lens tabs with the interior

the removal of any accumulation of

light housing notches and snap the

salt, dirt, mud, and other foreign

lens into place.

materials. Make sure the drain holes

in the lower edges of the doors and

rocker panels are kept clear and

CAUTION

clean.

Use care not to dirty or damage

Insects, tar, tree sap, bird droppings,

lens, lens tab, and plastic hous-

industrial pollution and similar

ings.

deposits can damage your vehicle’s

finish if not removed immediately.

Even prompt washing with plain

water may not completely remove all

these deposits.

A mild soap, safe for use on painted

surfaces, may be used.

After washing, rinse the vehicle thor-

oughly with lukewarm or cold water.

Do not allow soap to dry on the fin-

ish.

7-79

Maintenance

CAUTION

WARNING

•

Do not use strong soap,

Wet brakes

chemical detergents or hot

After washing the vehicle, test

water, and do not wash the

the brakes while driving slowly

vehicle in direct sunlight or

to see if they have been affected

when the body of the vehicle

by water. If braking performance

is warm.

is impaired, dry the brakes by

•

Be careful when washing the

applying them lightly while

side windows of your vehicle.

maintaining a slow forward

Especially, with high-pressure

speed.

OEU064036

water, water may leak through

the windows and wet the inte-

CAUTION

rior.

•

To prevent damage to the

•

Water washing in the engine

plastic parts and lamps, do

compartment including high

not clean with chemical sol-

pressure water washing may

vents or strong detergents.

cause the failure of electrical

circuits located in the engine

compartment.

•

Never allow water or other liq-

uids to come in contact with

electrical/electronic compo-

nents inside the vehicle as

this may damage them.

7-80

Waxing

Finish damage repair

CAUTION

Wax the vehicle when water will no

Deep scratches or stone chips in the

longer bead on the paint.

painted surface must be repaired

• Wiping dust or dirt off the

promptly. Exposed metal will quickly

Always wash and dry the vehicle

body with a dry cloth will

before waxing. Use a good quality

rust and may develop into a major

scratch the finish.

repair expense.

liquid or paste wax, and follow the

• Do not use steel wool, abra-

manufacturer’s instructions. Wax all

sive cleaners, or strong deter-

metal trim to protect it and to main-

NOTICE

gents containing highly alka-

tain its luster.

line or caustic agents on

If your vehicle is damaged and

Removing oil, tar, and similar materi-

chrome-plated or anodized

requires any metal repair or

als with a spot remover will usually

aluminum parts. This may

replacement, be sure the body

strip the wax from the finish. Be sure

result in damage to the pro-

shop applies anti-corrosion mate-

to re-wax these areas even if the rest

tective coating and cause dis-

rials to the parts repaired or

of the vehicle does not yet need wax-

coloration or paint deteriora-

replaced.

ing.

tion.

7-81

Maintenance

Bright-metal maintenance

Underbody maintenance

WARNING

•

To remove road tar and insects,

Corrosive materials used for ice and

use a tar remover, not a scraper or

snow removal and dust control may

After washing the vehicle, test

other sharp object.

collect on the underbody. If these

the brakes while driving slowly

•

To protect the surfaces of bright-

materials are not removed, acceler-

to see if they have been affected

ated rusting can occur on underbody

metal parts from corrosion, apply a

by water. If braking performance

coating of wax or chrome preser-

parts such as the fuel lines, frame,

is impaired, dry the brakes by

floor pan and exhaust system, even

vative and rub to a high luster.

applying them lightly while

though they have been treated with

•

During winter weather or in coastal

maintaining a slow forward

rust protection.

areas, cover the bright metal parts

speed.

Thoroughly flush the vehicle under-

with a heavier coating of wax or

body and wheel openings with luke-

preservative. If necessary, coat the

warm or cold water once a month,

parts with non-corrosive petroleum

after off-road driving and at the end

jelly or other protective compound.

of each winter. Pay special attention

to these areas because it is difficult

to see all the mud and dirt. It will do

more harm than good to wet down

the road grime without removing it.

The lower edges of doors, rocker

panels, and frame members have

drain holes that should not be

allowed to clog with dirt; trapped

water in these areas can cause rust-

ing.

7-82

Aluminum or chrome wheel

Corrosion protection

High-corrosion areas

maintenance

Protecting your vehicle from corro-

If you live in an area where your vehi-

The aluminum or chrome wheels are

sion

cle is regularly exposed to corrosive

coated with a clear protective finish.

materials, corrosion protection is

By using the most advanced design

particularly important. Some of the

•

Do not use any abrasive cleaner,

and construction practices to combat

common causes of accelerated cor-

polishing compound, solvent, or

corrosion, we produces vehicles of

rosion are road salts, dust control

wire brushes on aluminum or

the highest quality. However, this is

chemicals, ocean air and industrial

chrome wheels. They may scratch

only part of the job. To achieve the

pollution.

or damage the finish.

long-term corrosion resistance your

vehicle can deliver, the owner's

•

Clean the wheel when it has

cooperation and assistance is also

Moisture breeds corrosion

cooled.

required.

Moisture creates the conditions in

•

Use only a mild soap or neutral

which corrosion is most likely to

detergent, and rinse thoroughly

Common causes of corrosion

occur. For example, corrosion is

with water. Also, be sure to clean

The most common causes of corro-

accelerated by high humidity, partic-

the wheels after driving on salted

roads. This helps prevent corro-

sion on your vehicle are:

ularly when temperatures are just

above freezing. In such conditions,

sion.

• Road salt, dirt and moisture that is

the corrosive material is kept in con-

•

Avoid washing the wheels with

allowed to accumulate underneath

tact with the vehicle surfaces by

high-speed vehicle wash brushes.

the vehicle.

moisture that is slow to evaporate.

•

Do not use any alkaline or acid

• Removal of paint or protective

Mud is particularly corrosive

detergent. It may damage and cor-

coatings by stones, gravel, abra-

because it is slow to dry and holds

rode the aluminum or chrome

sion or minor scrapes and dents

moisture in contact with the vehicle.

wheels coated with a clear protec-

which leave unprotected metal

Although the mud appears to be dry,

tive finish.

exposed to corrosion.

it can still retain the moisture and

promote corrosion.

7-83

Maintenance

High temperatures can also acceler-

Keep your vehicle clean

• When cleaning lower door panels,

ate corrosion of parts that are not

rocker panels and frame mem-

The best way to prevent corrosion is

properly ventilated so the moisture

bers, be sure that drain holes are

to keep your vehicle clean and free

can be dispersed. For all these rea-

kept open so that moisture can

of corrosive materials. Attention to

sons, it is particularly important to

escape and not be trapped inside

the underside of the vehicle is partic-

keep your vehicle clean and free of

to accelerate corrosion.

ularly important.

mud or accumulations of other mate-

rials. This applies not only to the vis-

Keep your garage dry

ible surfaces but particularly to the

• If you live in a high-corrosion area

underside of the vehicle.

- where road salts are used, near

Don't park your vehicle in a damp,

the ocean, areas with industrial

poorly ventilated garage. This cre-

pollution, acid rain, etc.-, you

ates a favorable environment for cor-

To help prevent corrosion

should take extra care to prevent

rosion. This is particularly true if you

You can help prevent corrosion from

corrosion. In winter, hose off the

wash your vehicle in the garage or

getting started by observing the fol-

underside of your vehicle at least

drive it into the garage when it is still

lowing:

once a month and be sure to clean

wet or covered with snow, ice or

the underside thoroughly when

mud. Even a heated garage can con-

winter is over.

tribute to corrosion unless it is well

ventilated so moisture is dispersed.

• When cleaning underneath the

vehicle, give particular attention to

the components under the fenders

and other areas that are hidden

from view. Do a thorough job; just

dampening the accumulated mud

rather than washing it away will

accelerate corrosion rather than

prevent it. Water under high pres-

sure and steam are particularly

effective in removing accumulated

mud and corrosive materials.

7-84

Keep paint and trim in good

Don't neglect the interior

Interior care

condition

Moisture can collect under the floor

Interior general precautions

Scratches or chips in the finish

mats and carpeting to cause corro-

Prevent chemicals such as perfume,

should be covered with "touch-up"

sion. Check under the mats periodi-

cosmetic oil, sun cream, hand clean-

paint as soon as possible to reduce

cally to be sure the carpeting is dry.

er, and air freshener from contacting

the possibility of corrosion. If bare

Use particular care if you carry fertil-

the interior parts because they may

metal is showing through, the atten-

izers, cleaning materials or chemi-

cause damage or discoloration. If

tion of a qualified body and paint

cals in the vehicle.

they do contact the interior parts,

shop is recommended.

These should be carried only in

wipe them off immediately. See the

proper containers and any spills or

instructions that follow for the proper

Bird droppings : Bird droppings are

leaks should be cleaned up, flushed

way to clean vinyl.

highly corrosive and may damage

with clean water and thoroughly

painted surfaces in just a few hours.

dried.

CAUTION

Always remove bird droppings as

soon as possible.

Never allow water or other liq-

uids to come in contact with

electrical/electronic

compo-

nents inside the vehicle as this

may damage them.

7-85

Maintenance

Cleaning the upholstery and

Cleaning the lap/shoulder belt

CAUTION

interior trim

webbing

Vinyl

Clean the belt webbing with any mild

When cleaning leather products

(steering wheel, seats etc.), use

Remove dust and loose dirt from

soap solution recommended for

cleaning upholstery or carpet. Follow

neutral detergents or low alco-

vinyl with a whisk broom or vacuum

hol content solutions. If you use

cleaner. Clean vinyl surfaces with a

the instructions provided with the

soap. Do not bleach or re-dye the

high alcohol content solutions

vinyl cleaner.

webbing because this may weaken

or acid/alkaline detergents, the

it.

color of the leather may fade or

Fabric

the surface may get stripped

Remove dust and loose dirt from fab-

off.

Cleaning the interior window

ric with a whisk broom or vacuum

glass

cleaner. Clean with a mild soap solu-

tion recommended for upholstery or

If the interior glass surfaces of the

carpets. Remove fresh spots imme-

vehicle become fogged (that is, cov-

diately with a fabric spot cleaner. If

ered with an oily, greasy or waxy

fresh spots do not receive immediate

film), they should be cleaned with

attention, the fabric can be stained

glass cleaner. Follow the directions

and its color can be affected. Also, its

on the glass cleaner container.

fire-resistant properties can be

reduced if the material is not proper-

CAUTION

ly maintained.

Do not scrape or scratch the

CAUTION

inside of the rear window. This

may result in damage to the rear

Using anything but recom-

window defroster grid.

mended cleaners and proce-

dures may affect the fabric’s

appearance and fire-resistant

properties.

7-86

EMISSION CONTROL SYSTEM

The emission control system of your

1. Crankcase emission control

2. Evaporative emission con-

vehicle is covered by a written limited

system

trol System

warranty. Please see the warranty

The positive crankcase ventilation

The Evaporative Emission Control

information contained in the Service

system is employed to prevent air

System is designed to prevent fuel

Passport in your vehicle.

pollution caused by blow-by gases

vapors from escaping into the atmos-

Your vehicle is equipped with an

being emitted from the crankcase.

phere.

emission control system to meet all

This system supplies fresh filtered air

emission regulations.

to the crankcase through the air

Canister

There are three emission control

intake hose. Inside the crankcase,

Fuel vapors generated inside the fuel

systems which are as follows.

the fresh air mixes with blow-by

tank are absorbed and stored in the

gases, which then pass through the

onboard canister. When the engine is

PCV valve into the induction system.

(1) Crankcase emission control sys-

running, the fuel vapors absorbed in

tem

the canister are drawn into the surge

tank through the purge control sole-

(2) Evaporative emission control sys-

noid valve.

tem

(3) Exhaust emission control system

Purge Control Solenoid Valve

(PCSV)

In order to assure the proper function

The purge control solenoid valve is

of the emission control systems, it is

controlled by the Engine Control

recommended that you have your

Module

(ECM); when the engine

vehicle inspected and maintained by

coolant temperature is low during

an authorized HYUNDAI dealer or

idling, the PCSV closes so that evap-

other repair shops that use qualified

orated fuel is not taken into the

technicians in accordance with the

engine. After the engine warms-up

maintenance schedule in this manu-

during ordinary driving, the PCSV

al.

opens to introduce evaporated fuel to

the engine.

7-87

Maintenance

3. Exhaust emission control

Engine exhaust gas precautions

•

Do not operate the engine in con-

system

(carbon monoxide)

fined or closed areas

(such as

garages) any more than what is

The Exhaust Emission Control

• Carbon monoxide can be present

necessary to move the vehicle in or

System is a highly effective system

with other exhaust fumes.

out of the area.

which controls exhaust emissions

Therefore, if you smell exhaust

while maintaining good vehicle per-

fumes of any kind inside your vehi-

•

When the vehicle is stopped in an

cle, have it inspected and repaired

open area for more than a short

formance.

immediately. If you ever suspect

time with the engine running,

exhaust fumes are coming into

adjust the ventilation system

(as

Vehicle modifications

your vehicle, drive it only with all

needed) to draw outside air into the

•

This vehicle should not be modi-

the windows fully open. Have your

vehicle.

fied. Modification of your vehicle

vehicle checked and repaired

•

Never sit in a parked or stopped

could affect its performance, safety

immediately.

vehicle for any extended time with

or durability and may even violate

the engine running.

governmental safety and emis-

WARNING

sions regulations.

•

When the engine stalls or fails to

start, excessive attempts to restart

In addition, damage or perform-

Exhaust

the engine may cause damage to

ance problems resulting from any

Engine exhaust gases contain

the emission control system.

modification may not be covered

carbon monoxide (CO). Though

under warranty.

colorless and odorless, it is

•

If you use unauthorized electronic

dangerous and could be lethal if

devices, it may cause the vehicle to

inhaled. Follow the instructions

operate abnormally, wire damage,

following to avoid CO poison-

battery discharge and fire. For your

ing.

safety, do not use unauthorized

electronic devices.

7-88

Content .. 24 25 26 27 ..