Hyundai H350 (2016 year). Instruction - part 25
Fuse/Relay panel description
NOTICE
Inside the fuse/relay box covers, you can find the fuse/relay label describing
Not all fuse panel descriptions in
fuse/relay name and capacity.
this manual may be applicable to
■ Inner fuse box (Instrument panel)
■ Battery fuse box
your vehicle. It is accurate at the
time of printing.
When you inspect the fuse box on
your vehicle, refer to the fuse box
label.
■ Inner fuse box (Driver’s seat side)
■ Main fuse box
7
OEU074059/OEU074060/OEU074058/OEU074039
7-55
Maintenance
Inner fuse panel (Instrument panel)
No.
Fuse rating
Fuse Name
Circuit Protected
WIPER &
1
15A
Front Wiper Motor, Washer Motor
WASHER
2
2
7.5A
BLOWER M/HI SIG
A/CON
1
3
7.5A
EMERGENCY
Emergency-Call (ACC)
CALL
4
25A
P/WDW LH
P/WDW Motor Left
5
20A
DDM
Drive Door Module (B+ MIRR)
6
25A
P/WDW RH
P/WDW Motor Right
P/OUTLET
7
15A
Power Outlet (Front Left)
(FR_LH)
1
8
7.5A
CM (B+)
CM
9
15A
MULTIMEDIA
AUDIO E300/E800(B+), AVN(B+), LDC Module(B+)
10
20A
ADM
Assist Door Module (B+ MIRR)
11
7.5A
START
START SIG
7-56
No.
Fuse rating
Fuse Name
Circuit Protected
Cluster (B+), A/C Control Module(B+), Drive Door Module(B+ECU), Assist Door Module(B+ECU),
12
10A
MEMORY
DTG(B+), OBDII (B+)
13
7.5A
BRAKE SW
Brake Switch, Stop Lamp
Cluster, Drive Door Module, Assist Door Module, A/C Control Module, Seat HTD Switch
14
10A
MODULE E-3
Left/Right, VDC off Switch, AVN, Seat HTD Module Left/Right, DTG, LDWS Module, RPAS
Sensor, Yaw Rate Sensor, Fuel Water Sensor
MIDDLE
15
10A
Middle Door Lock Actuator
DR LOCK
TAILGATE
16
10A
Tailgate Door Lock Actuator
DR LOCK
17
10A
MODULE E-4
AUDIO E300/E800(ACC), AVN(ACC), LDC Module(ACC), CM(ACC)
ENG BOX
18
20A
UH BOX (ABS3 7.5A, SNSR5 7.5A, INHIBITOR 7.5A, BACK UP LAMP 7.5A)
(IG1)
19
10A
DCU
SEAT BOX (DCU SNSR Relay 'S')
2
20
7.5A
CM (IG1)
7
CM
21
7.5A
MODULE-1
Rain Sensor
SEAT BOX(PASS ROOM LAMP Relay 'S'), Key Warning Switch, Step Lamp(MID/ASS),
22
10A
INTERIOR LAMP
OH_CONSOLE Lamp, Map Lamp, Passenger Reading Lamp, Cargo_Lamp(Middle / TGAT)
7-57
Maintenance
No.
Fuse rating
Fuse Name
Circuit Protected
HLLD Actuator Left/Right, Glow Relay Module(IG1), Brake Switch, FPAS Sensor, C/PAD Switch,
23
10A
MODULE-2
BEZEL Switch, LDC Module(IG1)
I_S_MIRR(IG2), CM(IG2), Passenger Heater Module(IG2), Seat HTD Module Left/Right(IG2),
24
7.5A
MODULE-5
F/FILTER Relay 'S'
2
25
10A
Immobilizer Module(B+), Key Warning Switch
IMMO
1
26
7.5A
Immobilizer Module(IG1)
IMMO
SEAT BOX
SEAT BOX (ELECTRIC VENTILATOR2 10A, A/CON RR(IG2) 10A, IG2 10A(AUX POWER(IG2)
27
20A
(IG2)
Relay 'S'))
1
28
7.5A
A/C Control Module(IG2)
A/CON
29
15A
A/BAG
A/BAG Control Module(IG1)
2
30
7.5
EMERGENCY
Emergency-Call(IG1)
CALL
7-58
Inner fuse panel (Driver's seat side)
No.
Fuse rating
Fuse Name
Circuit Protected
PASS A/CON
1
30A
Passenger A/CON Blower Motor Left
BLOW LH
2
20A
E/POWER STEP
Electric Step Module(B+)
PASS A/CON
3
30A
Passenger A/CON Blower Motor Right
BLOW RH
1
4
7.5A
ELECTRIC
Ventilator Control Module(B+)
VENTILATOR
ROOM LAMP
5
10A
Room Lamp(Front/Center/Rear)
PASS
AUX POWER
6
15A
AUX BOX (AUX IG2)
(IG2)
1
7
30A
Trailer Module(B+)
TRAILER
SEAT
8
25A
Seat HTD Module Left/Right (Warm B+)
HEATER
7
AUX POWER
9
10A
AUX BOX (ENGINE RUN)
(ENGINE RUN)
2
10
15A
Trailer Module(B+)
TRAILER
11
20A
PRE HEATER 1
Pre Heater Module
AUX POWER
12
25A
AUX BOX (AUX B+)
(B+)
7-59
Maintenance
No.
Fuse rating
Fuse Name
Circuit Protected
3
13
15A
Trailer Module(B+)
TRAILER
PASS A/CON
14
30A
Passenger A/CON Blower Motor Left
C/FAN LH
BATTERY
15
10A
Battery Sensor
SENSOR
16
30A
FUEL HTR
Fuel Filter HTR
PASS HTR/BLOW
17
7.5A
Passenger Heater Control Module (Blower Motor SIG Front)
SIG FR
DCU
18
15A
PM Sensor, NOX Sensor (front/Rear), Dosing Control Module (IG1 INPUT)
SENSOR
1
19
20A
Dosing Control Module(B+)
DCU
PASS HTR/BLOW
20
7.5A
Passenger Heater Control Module (Blower Motor SIG Rear)
SIG RR
2
21
10A
ELECTRIC
Ventilator Control Module (IG2)
VENTILATOR
PASS A/CON
22
7.5A
A/C Control Module Rear (Blower Motor SIG Left)
BLOW SIG LH
PASS A/CON
23
7.5A
A/C Control Module Rear (Blower Motor SIG Right)
BLOW SIG RH
A/CON RR
24
10A
A/C Control module Rear
(IG2)
7-60
No.
Fuse rating
Fuse Name
Circuit Protected
2
25
20A
Dosing Control Module(B+)
DCU
3
26
20A
Dosing Control Module(B+)
DCU
27
10A
IG2
Electric Step Module, SEAT BOX(AUX POWER (IG2) Relay 'S')
PASS A/CON
28
30A
Passenger A/CON Blower Motor Right
C/FAN RH
PASS HTR
29
25A
Passenger Heater Blower Motor Front
FRT
PASS HTR
30
25A
Passenger Heater Blower Motor Rear
RR
7
7-61
Maintenance
Engine compartment main fuse panel
No.
Fuse rating
Fuse Name
Circuit Protected
2
1
10A
A/C Compressor PASS
A/CON
4
2
15A
Engine Control Module (Permanent Battery (+))
ECU
1
3
10A
A/C Compressor CAB
A/CON
1
4
10A
Electric VGT Actuator, EGR Cooling Bypass, UH_BOX(Fuel Pump Relay 'S')
SENSOR
5
10A
SPARE
1
6
20A
Engine Control Module (Battery (+))
ECU
2
7
10A
UH_BOX(A/CON1 Relay 'S', A/CON2 Relay 'S', CONDENSER FAN Relay LH,RH1/2 'S')
SENSOR
2
8
20A
Engine Control Module (Battery (+))
ECU
3
9
10A
LAMBDA Sensor
SENSOR
BACK UP
Rear Combi Lamp Left/Right (Back Up), Inside Mirror (Reverse), Trailer Module (Back Up),
10
7.5A
LAMP
Vehicle Dynamic Control Module (Reverse Gear Switch), Reverse Warning Buzzer
3
Anti-Lock Brake Module (IG1), Vehicle Dynamic Control Module (IG1), Steering Angle Sensor
11
7.5A
ABS
(IG1)
5
12
7.5A
Air Flow Sensor, Engine Control Module (TERMINAL15(IG1 INPUT))
SENSOR
7-62
No.
Fuse rating
Fuse Name
Circuit Protected
13
7.5A
INHIBITOR
UH_BOX(Start Inhibit Relay 'S')
3
14
60A
Smart Junction Box (B+3)
B+
15
60A
VDC
Vehicle Dynamic Control Module (B+ Pump Motor)
2
Anti-Lock Brake Module (B+ Solenoid Valve), Vehicle Dynamic Control Module(B+ Solenoid
16
40A
ABS
Valve)
1
17
40A
Anti-Lock Brake Module (B+ Pump Motor)
ABS
2
18
60A
Smart Junction Box (B+2)
B+
19
80A
GLOW
Glow Relay Module (Plus Direct)
4
20
50A
Smart Junction Box (B+4)
B+
21
50A
EMS
Engine Management System Block (B+)
7
22
15A
HORN
HORN
23
10A
PTO
PTO Magnetic Valve
24
20A
F/PUMP
Fuel Pump Sender (Fuel Pump Motor(+))
7-63
Maintenance
No.
Fuse rating
Fuse Name
Circuit Protected
25
15A
B/A HORN
Burglar Alarm Horn
C/LIGHTER
26
25A
P/OUTLET
Cigar Lighter, luggage Room Power Outlet
RR
P/OUTLET
27
25A
Power Outlet (Center, front Right)
CTR & RH
28
20A
DEICER
DEICER
29
40A
CONDENSER FAN
A/C Condenser Fan Motor Left/Right
WIPER
30
30A
Front Wiper Motor
FRT
4
31
50A
PTC
PTC Heater EXTN (PTC4+)
HEATER
3
32
50A
PTC
PTC Heater EXTN (PTC3+)
HEATER
2
33
50A
PTC
PTC Heater EXTN (PTC2+)
HEATER
1
34
50A
PTC
PTC Heater EXTN (PTC1+)
HEATER
7-64
No.
Fuse rating
Fuse Name
Circuit Protected
35
40A
IG2
IGN_Switch (B2), Start Solenoid
36
50A
IG1
IGN_Switch (B1)
1
37
50A
Smart Junction Box (B+1)
B+
38
50A
BLOWER
Blower Motor
150A
ALT
ALTERNATOR
39
200A
ALT
ALTERNATOR
7
7-65
Maintenance
Battery fuse panel
No.
Fuse rating
Fuse Name
Circuit Protected
1
40A
DCU_MAIN
Dosing Control Module (B+)
1. BUS : SEAT BOX (PASS HTR FRT 25A, PASS HTR/BLOW SIG FR 7.5A, PASS HTR RR 25A,
PASS,HTR(BUS)
PASS HTR/BLOW SIG RR 7.5A, PASS A/CON C/FAN LH 30A, PASS A/CON C/FAN RH 30A,
2
150A
PASS,A/CON(BUS)
PASS A/CON BLOW LH 30A, PASS A/CON BLOW SIG LH 7.5A, PASS A/CON BLOW RH 30A,
AUX,BATT(TRK/VAN)
PASS A/CON BLOW SIG RH 7.5A)
2. VAN/TRUCK : AUX Battery
2
SEAT BOX (B+2/B+3), PM Sensor, NOX Sensor (front/Rear), Dosing Control Module (IG1
3
70A
SEAT_F/BOX
INPUT)
1
4
70A
SEAT BOX (B+1/B+4)
SEAT_F/BOX
7-66
LIGHT BULBS
NOTICE
WARNING
CAUTION
After heavy, driving rain or wash-
Working on the lights
If you don’t have necessary
ing, headlight and taillight lenses
tools, the correct bulbs and the
could appear frosty. This condi-
Prior to working on the light,
expertise, we recommend that
tion is caused by the temperature
firmly apply the parking brake,
you consult an authorized
difference between the lamp
ensure that the ignition switch
HYUNDAI dealer. In many cases,
inside and outside. This is similar
is turned to the “LOCK” position
it is difficult to replace vehicle
to the condensation on your win-
and turn off the lights to avoid
light bulbs because other parts
dows inside your vehicle during
sudden movement of the vehi-
of the vehicle must be removed
the rain and doesn’t indicate a
cle and burning your fingers or
before you can get to the bulb.
problem with your vehicle. If
receiving an electric shock.
This is especially true if you
water leaks into the lamp bulb cir-
have to remove the headlight
cuitry, we recommend that the
assembly to get to the bulb(s).
system be checked by an author-
Use only the bulbs of the specified
ized HYUNDAI dealer.
Removing/installing the head-
wattage.
light assembly can result in
damage to the vehicle.
CAUTION
Be sure to replace the burned-
out bulb with one of the same
7
wattage rating. Otherwise, it
may cause damage to the fuse
or electric wiring system.
7-67
Maintenance
Headlight, position light, turn
(1) Front turn signal light
Headlight (Replacement)
signal light, front fog light bulb
(2) Headlight (Low)
replacement
(3) Headlight (High)
■ MFR type
(4) Position light and DRL
(LED)
(if equipped)
(5) Front fog light (if equipped)
OEU074048
OEU074070
■ Projection type
MFR type (High / Low) and projec-
tion type (High)
1.Open the hood.
2.Remove the headlight bulb cover
by turning it counterclockwise.
3.Disconnect the headlight bulb
socket-connector.
4.Unsnap the headlight bulb retain-
ing wire by depressing the end and
OEU074047
pushing it upward.
5.Remove the bulb from the head-
light assembly.
7-68
6.Install a new headlight bulb and
(Continued)
snap the headlight bulb retaining
wire into position by aligning the
•
Always handle them carefully,
wire with the groove on the bulb.
and avoid scratches and abra-
sions. If the bulbs are lit, avoid
7.Connect the headlight bulb socket-
contact with liquids. Never
connector.
touch the glass with bare
8.Install the headlight bulb cover by
hands. Residual oil may cause
turning it clockwise.
the bulb to overheat and burst
when lit. A bulb should be
operated only when installed
Projection type (Low)
in a headlight.
1.Open the hood.
OEU074062
•
If a bulb becomes damaged or
2.Remove the headlight bulb cover
cracked, replace it immediate-
by turning it counterclockwise.
WARNING
ly and carefully dispose of it.
3.Remove the bulb socket by turning
•
Wear eye protection when
it counterclockwise and remove by
Halogen bulbs
changing a bulb. Allow the
pulling the bulb.
• Halogen bulbs contain pres-
bulb to cool down before han-
4.Install is the reverse order of
surized gas that will produce
dling it.
removal.
flying pieces of glass if bro-
ken.
7
NOTICE
(Continued)
We recommend that the headlight
aiming be adjusted after an acci-
dent or after the headlight assem-
bly is reinstalled at an authorized
HYUNDAI dealer.
7-69
Maintenance
Turn signal light/Position light
Front fog light bulbs
Headlight and front fog light
Turn signal light
(if equipped)
aiming (for Europe)
1.Turn off the engine and open the
1.Remove the front bumper under
Headlight aiming
hood.
cover.
■ MFR type
2.Remove the socket from the
2.Reach your hand into the back of
the front bumper.
assembly by turning the socket
counterclockwise until the tabs on
3.Disconnect the power connector
the socket align with the slots on
from the socket.
the assembly.
4.Remove the bulb-socket from the
3.Remove the bulb from the socket
housing by turning the socket
by pressing it in and rotating it
counter clockwise until the tabs on
counterclockwise until the tabs on
the socket align with the slots on
the bulb align with the slots in the
the housing.
OEU074049
socket. Pull the bulb out of the
■ Projection type
5.Install the new bulb-socket into the
socket
housing by aligning the tabs on the
4.Insert a new bulb by inserting it into
socket with the slots in the hous-
the socket and rotating it until it
ing. Push the socket into the hous-
locks into place.
ing and turn the socket clockwise.
5.Install the socket in the assembly
6.Connect the power connector to
by aligning the tabs on the socket
the socket.
with the slots in the assembly.
7.Reinstall the front bumper under
Push the socket into the assembly
cover.
and turn the socket clockwise.
OEU074061
1.Inflate the tires to the specified
Position light
pressure and remove any loads
If the light bulb does not operate, we
from the vehicle except the driver,
recommend that the system be
spare tire, and tools.
checked by an authorized HYUNDAI
dealer.
7-70
2.The vehicle should be placed on a
5-2. Projection type
Front fog light aiming
flat floor.
1) Low beam aiming
■ Fog light aiming
3.Draw vertical lines (Vertical lines
To aim the low beam left or
passing through respective head
right, turn the screw (3) clock-
lamp centers) and a horizontal line
wise or counterclockwise.
(Horizontal line passing through
To aim the low beam up or
center of head lamps) on the
down, turn the screw (4) clock-
screen.
wise or counterclockwise.
4.With the head lamp and battery in
2) High beam aiming
normal condition, aim the head
High beam aiming is available
lamps so the brightest portion falls
up direction or down.
on the horizontal and vertical lines.
To aim the high beam up or
5-1. MFR type
OEU074050
down, turn the screw (5) clock-
To aim the low/high beam left or
wise or counterclockwise.
The front fog light can be aimed as
right, turn the screw (1) clockwise
the same manner of the head lamps
or counterclockwise. To aim the
aiming.
low/high beam up or down, turn the
With the front fog lights and battery
screw
(2) clockwise or counter-
normal condition, aim the front fog
clockwise.
lights. To aim the front fog light up or
down, turn the bolt clockwise or
7
counterclockwise.
7-71