Hyundai Tiburon (2008 year). Instruction - part 4
1FEATURES OF YOUR HYUNDAI
WARNING AND INDICATOR LIGHTS
48
B260D01A-AAT
B260W02JM-GAT
B265W02JM-GAT
Turn Signal Indicator Lights
Low tire pressure telltale
TPMS (Tire Pressure Monitor-
ing System) malfunction indi-
cator
The blinking green arrows on the instrument
The low tire pressure telltale comes on for 3
panel show the direction indicated by the turn
seconds after the ignition key is turned to the
TPMS malfunction indicator comes on for 3
signals. If the arrow comes on but does not blink,
"ON" position.
seconds after the ignition key is turned to the
blinks more rapidly than normal, or does not
If the warning light does not come on, or continu-
"ON" position. If the warning light does not come
illuminate at all, a malfunction in the turn signal
ously remains on after coming on for about 3
on, or continuously remains on after coming on
system is indicated. Your dealer should be
seconds when you turned the ignition key to the
for about 3 seconds when you turned the ignition
consulted for repairs.
"ON" position, the Tire Pressure Monitoring
key to the "ON" position, the Tire Pressure
System is not working properly. If this occurs,
Monitoring System is not working properly. If
have your vehicle checked by an authorized
this occurs, have your vehicle checked by an
Hyundai dealer as soon as possible.
authorized Hyundai dealer as soon as possible.
This warning light will also illuminate if one or
The warning light also comes on and stays on
more of your tires is significantly under-inflated.
B265C03LZ-AAT
when there is a problem with the Tire Pressure
You should stop and check your tires as soon
Electronic Stability
Monitoring System.
as possible. If the warning light illuminates while
If this happens, the system may not monitor the
Control Indicator Lights
driving, reduce vehicle speed immediately and
tire pressure. Have the system checked by an
(If installed)
stop the vehicle. Avoid hard braking and over-
authorized Hyundai dealer as soon as possible.
correcting at the steering wheel. Inflate the tires
The electronic stability control indicators change
to the proper pressure as indicated on the
operation according to the ignition switch posi-
vehicle’s tire information placard.
tion and whether the system is in operation or
!
not.
WARNING:
They will illuminate when the ignition key is
o The TPMS cannot alert you to severe and
turned to the "ON" position, but should go out
!
WARNING:
sudden tire damage caused by external
after approximately three seconds. If the ESC
factors.
Significantly low tire pressure makes the
or ESC-OFF indicator stays on, take your car
o If you feel any vehicle instability, imme-
vehicle unstable and can contribute to loss
to your authorized Hyundai dealer and have the
diately take your foot off the accelerator
of vehicle control and increased braking
system checked. See section 2 for more infor-
and slowly move to a safe position off
distances.
mation about the ESC.
the road.
Continued driving on low pressure tires will
cause the tires to overheat and fail.
FEATURES OF YOUR HYUNDAI
1
49
B260J01A-AAT
B260B01JM-AAT
B260E02L-AAT
Charging System Warning Light
SRS (Airbag) Warning Light
Seat Belt Reminder Light And
Chime
The charging system warning light should come
The SRS service reminder indicator (SRI) comes
Seat belt reminder light comes and stays on until
on when the ignition is turned on, then go out
on for about 6 seconds after the ignition key is
the seat belt is fastened when the ignition key is
when the engine is running. If the light stays on
turned to the "ON" position or after the engine
turned to "ON" or "START".
while the engine is running, there is a malfunc-
is started, after which it will go out.
And, the warning chime will also sound for about
tion in the electrical charging system. If the light
6 seconds.
comes on while you are driving, stop, turn off the
This light also comes on when the SRS is not
engine and check under the hood. First, make
working properly. If the SRI does not come on,
certain the generator drive belt is in place. If it is,
or continuously remains on after coming on for
check the tension of the belt. Do this as shown
about 6 seconds when you turned the ignition
on page 6-19 by pushing down on the center of
key to the "ON" position or started the engine,
the belt. Have the system checked by your
or if it comes on while driving, have the SRS
Hyundai dealer as soon as possible.
inspected by an authorized Hyundai Dealer.
B260F01A-AAT
High Beam Indicator Light
The high beam indicator light comes on when-
ever the headlights are switched to the high
beam or flash position.
1FEATURES OF YOUR HYUNDAI
50
B260G01A-AAT
B260N02A-AAT
B260H02GK-AAT
Low Oil Pressure Warning Light
Malfunction Indicator
Parking Brake/Low Brake Fluid
Light
Level Warning Light
This light illuminates when there is a malfunction
of an exhaust gas related component, and the
!
system is not functioning properly so that the
!
CAUTION:
CAUITON:
exhaust gas regulation values are not satisfied.
If the oil pressure warning light stays on
If you suspect brake trouble, have your
This light will also illuminate when the ignition key
while the engine is running, serious engine
brakes checked by a Hyundai dealer as
is turned to the "ON" position, and then it will go
damage may result. The oil pressure warn-
soon as possible. Driving your car with a
out in a few seconds after the engine is started.
ing light comes on whenever there is insuf-
problem in either the brake electrical sys-
If it illuminates while driving, or does not illumi-
ficient oil pressure. In normal operation, it
tem or brake hydraulic system is danger-
nate when the ignition key is turned to the "ON"
should come on when the ignition switch
ous, and could result in a serious injury or
position, take your car to your nearest autho-
is turned on, then go out when the engine
death.
rized Hyundai dealer and have the system
is started. If the oil pressure warning light
checked.
stays on while the engine is running, there
Warning Light Operation
is a serious malfunction.
If this happens, stop the car as soon as it is
The parking brake/low brake fluid level warning
safe to do so, turn off the engine and check
light should come on when the parking brake is
the oil level. If the oil level is low, fill the
B260M01A-AAT
applied and the ignition switch is turned to "ON"
engine oil to the proper level and start the
Low Fuel Level Warning Light
or "START". After the engine is started, the light
engine again. If the light stays on with the
should go out when the parking brake is re-
engine running, turn the engine off imme-
leased.
diately. In any instance where the oil light
The low fuel level warning light comes on when
If the parking brake is not applied, the warning
stays on when the engine is running, the
the fuel tank is approaching empty. When it
light should come on when the ignition switch is
engine should be checked by a Hyundai
comes on, you should add fuel as soon as
turned to "ON" or "START", then go out in three
dealer before the car is driven again.
possible. Driving with the fuel level warning light
seconds. If the light comes on at any other time,
on or with the fuel level below "E" can cause the
you should slow the vehicle and bring it to a
engine to misfire and damage the catalytic
complete stop in a safe location off the roadway.
converter.
FEATURES OF YOUR HYUNDAI
1
51
B260Q01E-GAT
B260K01F-AAT
The brake fluid level warning light indicates that
the brake fluid level in the brake master cylinder
CRUISE Indicator Light
Tail Gate Open Warning Light
is low and hydraulic brake fluid conforming to
(If Installed)
DOT 3 or DOT 4 specifications should be
added. After adding fluid, if no other trouble is
This light remains on unless the tail gate is
found, the car should be immediately and care-
The cruise indicator light in the instrument clus-
completely closed and latched.
fully driven to a Hyundai dealer for inspection.
ter is illuminated when the cruise control main
If further trouble is experienced, the vehicle
switch on the end of the barrel is pushed.
should not be driven at all but taken to a dealer
The indicator light does not illuminate when the
by a professional towing service.
cruise control main switch is pushed a second
Your Hyundai is equipped with dual-diagonal
time.
braking systems. This means you still have
Information about the use of cruise control is
braking on two wheels even if one of the dual
beginning on page 1-80.
systems should fail. With only one of the dual
systems working, more than normal pedal travel
and greater pedal pressure are required to stop
B260R01E-GAT
B260L02HP-GAT
the car. Also, the car will not stop in as short a
CRUISE SET Indicator Light
Door Ajar Warning Light and
distance with only half of the brake system
(If installed)
Chime
working. If the brakes fail while you are driving,
shift to a lower gear for additional engine braking
The set indicator light in the instrument cluster
The door ajar warning light warns you that a door
and stop the car as soon as it is safe to do so.
is illuminated when the cruise control switch is
is not completely closed and the chime warns
pushed downward to "SET (COAST)".
you that the key is in the ignition switch.
The set indicator light does not illuminate when
the control switch is in the "CANCEL" position.
NOTE :
The warning chime only sounds whenever
the key is in the ignition switch and the
driver's side front door is open simulta-
neously. The chime sounds until the key is
removed from the ignition switch or the
driver's side front door is closed.
1FEATURES OF YOUR HYUNDAI
INSTRUMENT CLUSTER
52
B260P02Y-GAT
B270A01A-AAT
B280A01TG-AAT
ABS Service Reminder Indica-
Brake Pad Wear Warning Sound
Fuel Gauge
tor (SRI)
The front disc brake pads have wear indicators
that should make a high-pitched squealing or
When the key is turned to the "ON" position, the
scraping noise when new pads are needed. The
Anti-Lock Brake System SRI will come on and
sound may come and go or be heard all the time
then go off in a few seconds. If the ABS SRI
when the vehicle is moving. It may also be heard
remains on, comes on while driving, or does not
when the brake pedal is pushed down firmly.
come on when the key is turned to the "ON"
Excessive rotor damage will result if the worn
position, this indicates that there may be a
pads are not replaced. See your Hyundai dealer
problem with the ABS.
immediately.
If this occurs, have your vehicle checked by
your Hyundai dealer as soon as possible. The
normal braking system will still be operational,
but without the assistance of the anti-lock brake
system.
OGK016259
The needle on the gauge indicates the approxi-
mate fuel level in the fuel tank. The fuel capacity
!
is given in Section 9.
WARNING:
If the both ABS SRI and Parking Brake/
NOTE:
Brake fluid level warning lights remain "ON"
or come on while driving, there may be a
The "
" symbol means the fuel filler lid
problem with E.B.D (Electronic Brake Force
is placed on the left side of the vehicle.
Distribution).
If this occurs, avoid sudden stops and have
your vehicle checked by your Hyundai dealer
as soon as possible.
FEATURES OF YOUR HYUNDAI
1
53
B290A02A-AAT
The needle on the engine coolant temperature
B330A03E-AAT
Engine Coolant Temperature Gauge
gauge should stay in the normal range. If it
Tachometer
moves across the dial to "H" (Hot), pull over and
stop as soon as possible and turn off the engine.
Then open the hood and after the engine has
cooled, check the coolant level and the water
pump drive belt. If you suspect cooling system
trouble, have your cooling system checked by
a Hyundai dealer as soon as possible.
B300A01A-AAT
Speedometer
OGK016261
OGK016265
The tachometer registers the speed of your
engine in revolutions per minute (rpm).
!
WARNING:
Never remove the radiator cap when the
engine is hot. The engine coolant is under
!
CAUTION:
pressure and could erupt and cause severe
The engine should not be raced to such a
burns. Wait until the engine is cool before
speed that the needle enters the red zone
removing the radiator cap.
on the tachometer face. This can cause
severe engine damage and may void your
warranty.
OGK016264
Your Hyundai's speedometer is calibrated in
miles per hour (on the outer scale) and kilome-
ters per hour (on the inner scale).
1FEATURES OF YOUR HYUNDAI
54
B310B02GK-AAT
Type A
1. Odometer
Odometer/Trip odometer
The odometer records the total driving distance
Type A
in miles, and is useful for keeping a record for
maintenance intervals.
NOTE:
Any alteration of the odometer may void
Type B
your warranty coverage.
2,3 Trip odometer
Records the distance of 2 trips in miles.
TRIP A: Distance you have traveled from your
HGK2061-1
origination point to a first destination.
Type B
TRIP B: Distance from the first destination to the
HGK028B
final destination.
Function of digital odometer/trip odom-
To shift from TRIP A to TRIP B, press the reset
eter
switch. When pressed for 1 second, it will reset
Pushing in the reset switch on the right side of
to 0.
the speedometer when the ignition switch is
turned "ON" will display the following sequence:
HGK055C
FEATURES OF YOUR HYUNDAI
1
TRIP COMPUTER
55
B400B04GK-AAT
Reset Switch
1. Distance to Empty
(If installed)
o The reset switch is used to zero the multi-
Type A
Type A
functional display mode.
o Pushing in the reset switch on the left side of
the tachometer changes the display as
follows;
Type B
Type B
DISTANCE TO EMPTY
AVERAGE SPEED
OGK016401N
OGK016400N
The trip computer is a microcomputer-con-
DRIVE TIME
o This mode provides the estimated distance
trolled driver information gauge that displays
to empty from the current fuel level in the fuel
information related to driving, such as estimated
tank.
distance to empty, average speed and drive
o The trip computer may not register additional
time on the LCD.
fuel if less than 1.36 gallons (6 liters) of fuel
are added to the vehicle.
o When the battery has been reinstalled after
being discharged or disconnected, drive
more than 20 miles (32km) for an accurate
distance to empty.
1FEATURES OF YOUR HYUNDAI
56
2. Average Speed
3. Drive Time
Type A
Type A
Type A
Type B
Type B
Type B
OGK046033N
OGK016402N
OGK016403N
o When the distance to empty is less than 31
miles (50 km), the symbol will always come
o This mode indicates the average speed
on and the distance to empty digits will
o This mode indicates the drive time travelled
travelled since the last average speed reset.
indicate "---" with flash until more fuel is
since the last drive time reset.
o To reset the average speed to zero, press
added.
o To reset the drive time to zero, press and
and hold the reset switch for more than 1
hold the reset switch for more than 1 second
second while the average speed is being
while the drive time is being displayed.
NOTE:
displayed.
o The distance to empty can differ from
the actual tripmeter according to driving
conditions.
o The distance to empty can vary accord-
ing to the driving conditions, driving
pattern or vehicle speed.
FEATURES OF YOUR HYUNDAI
1
MULTI GAUGE
57
B330C02GK-GAT
(If installed)
The multi gauge consists of a torque gauge,
instantaneous fuel consumption gauge, and
volt meter.
B330C04GK
B330C03GK
Instantaneous fuel Consumption gauge
Volt gauge
It shows instantaneous fuel consumption ac-
It shows moment volt change and makes for
cording to driving conditions. The more indi-
diver correspond to low volt situation.
B330C01GK
cated figure is low, the more it indicates efficient
driving situation.
Torque gauge
It shows instantaneous change of the torque by
rpm.
1FEATURES OF YOUR HYUNDAI
MULTI-FUNCTION LIGHT SWITCH
58
B340A01A-AAT
B340B01A-AAT
B340C03E-AAT
Combination Turn Signal, Headlight and
Lane Change Signal
Headlight Switch
High-beam Switch
Turn signal operation
Pulling down on the lever causes the turn
signals on the left side of the car to blink. Pushing
upwards on the lever causes the turn signals on
the right side of the car to blink. As the turn is
completed, the lever will automatically return to
the center position and turn off the turn signals
at the same time. If either turn signal indicator
light blinks more rapidly than usual, goes on but
does not blink, or does not go on at all, there is
a malfunction in the system. Check for a burned-
out fuse or bulb or see your Hyundai dealer.
HGK2079
HGK2074
To indicate a lane change, move the lever up or
To operate the headlights, turn the barrel on the
down to a point where it begins flashing.
end of the multi-function switch. The first posi-
The lever will automatically return to the center
tion turns on the parking lights, sidelights, tail
position when released.
lights and instrument panel lights. The second
position turns on the headlights.
NOTE:
The ignition must be in the "ON" position
to turn on the headlight.
FEATURES OF YOUR HYUNDAI
1
59
B340G02LZ-GAT
Parking light auto cut
Auto Light (If installed)
o The purpose of this feature is to prevent the
battery from being discharged. The system
automatically turns off the parking light when
the driver removes the ignition key and
opens the driver- side door.
o With this feature, the parking light will be
turned off automatically if the driver parks on
the side of road at night.
If necessary, to keep the lights on when the
ignition key is removed, perform the following :
Auto Light Sensor
1) Open the driver-side door.
OGK026223C
2) Turn the parking light OFF and ON again
using the light switch on the steering column.
NOTE:
OGK026223N
o Never place anything over the sensor
To operate the automatic light feature, turn the
located on the instrument panel, to en-
barrel on the end of the multi-function switch. If
sure better auto light system control.
you set the multi-function switch to "AUTO", the
o Don't clean the sensor using a window
B340D01A-AAT
tail lights and headlights will be turned automati-
cleaner.
High-beam Switch
cally on or off according to external illumination.
o If your vehicle has window tint or other
To turn on the headlight high beams, push the
types of coating on the front windshield,
lever forward (away from you). The high beam
NOTE:
the AUTO light system may not work
indicator light will come on at the same time. For
Switch on head light manually in foggy,
properly.
low beams, pull the lever back toward you.
cloudy and rainy conditions.
1FEATURES OF YOUR HYUNDAI
WINDSHIELD WIPER AND WASHER
60
B340E01A-AAT
B350A01GK-AAT
A :Wiper speed control
Headlight Flasher
Type A
· MIST - Single wipe
· OFF - Off
· INT - Intermittent wipe
· LO - Low wiper speed
· HI - High wiper speed
B :Intermittent wipe time adjustment
C :Wash with brief wipes
OGK048905
HGK2077
Type B
B350A01A-AAT
To flash the headlights, pull the switch lever
Windshield Wiper and Washer Switch
toward you, then release it. The headlights can
Type A
be flashed even though the headlight switch is
in the "OFF" position.
OGK048901N
OGK047046N
FEATURES OF YOUR HYUNDAI
1
61
B350B01O-AAT
When the washer lever is operated, the wipers
Type B
Windshield Washer Operation
automatically make two passes across the
windshield. The washer continues to operate
Type A
until the lever is released.
NOTE:
o
Do not operate the washer more than 15
seconds at a time or when the fluid
reservoir is empty.
o
In icy or freezing weather, be sure the
wiper blades are not frozen to the glass
prior to operating the wipers.
o
In areas where water freezes in winter,
OGK048900N
use windshield washer antifreeze.
The windshield wiper switch has three posi-
OGK047048N
tions:
Type B
(1)Intermittent wiper operation
(2)Low-speed operation
(3)High-speed operation
NOTE:
To prevent damage to the wiper system, do
not attempt to wipe away heavy accumula-
tions of snow or ice. Accumulated snow
and ice should be removed manually. If
there is only a light layer of snow or ice,
operate the heater in the defrost mode to
melt the snow or ice before using the wiper.
OGK048048N
To use the windshield washer, pull the wiper/
washer lever toward the steering wheel.
1FEATURES OF YOUR HYUNDAI
62
B350C01S-AAT
With the switch in this position, the interval
Mist Wiper Operation
Adjustable Intermittent Wiper Operation
between wipes can be varied from 2 to 10
Type A
seconds by turning the interval adjuster barrel.
Type A
OGK047049N
OGK047050N
Type B
Type B
OGK048049N
OGK048050N
If a single wipe is desired in mist, move the
To use the intermittent wiper feature, place the
windshield wiper and washer control lever up.
wiper switch in the "INT" position.
FEATURES OF YOUR HYUNDAI
1
FRONT FOG LIGHT SWITCH
HAZARD WARNING SYSTEM
REAR WINDOW DEFROSTER
63
SWITCH
B360A04A-AAT
B370A01A-AAT
B380A02A-AAT
Type A
OGK046052
OGK066001
Type B
To turn on the front fog lights, push the switch.
The hazard warning system should be used
They will light when the headlight switch is in the
whenever you find it necessary to stop the car
second position and the ignition key is in the
in a hazardous location. When you must make
"ON" position.
such an emergency stop, always pull off the
road as far as possible.
NOTE:
The hazard warning lights are turned on by
If you turn on the headlight high beams, the
pushing in the hazard switch. This causes all
OGK046054-1N
front fog lights will be turned off.
turn signal lights to blink. The hazard warning
lights will operate even though the key is not in
The rear window defroster and heated outside
the ignition.
rearview mirrors are turned on by pushing in the
To turn the hazard warning lights off, push the
switch. To turn the defroster off, push the switch
switch a second time.
a second time. The rear window defroster
automatically turns itself off after about 20 min-
utes. To restart the defroster cycle, push in the
switch again after it has turned itself off.
1FEATURES OF YOUR HYUNDAI
DIGITAL CLOCK
INSTRUMENT PANEL LIGHT
64
CONTROL (RHEOSTAT)
B400A01A-AAT
B410A01A-AAT
!
CAUTION:
Do not clean the inner side of the rear
window glass with an abrasive type of glass
cleaner or use a scraper to remove foreign
deposits from the inner surface of the glass
as this may cause damage to the defroster
elements.
NOTE:
The engine must be running for the rear
window defroster to operate.
OGK046056
OGK046029
There are three control buttons for the digital
The instrument panel lights can be made brighter
clock. Their functions are:
or dimmer by turning the instrument panel light
control knob.
H - Push "H" to advance the hour indicated.
M - Push "M" to advance the minute indicated.
R - Push "R" to reset minutes to ":00" to
facilitate resetting the clock to the correct
time. When this is done:
Pressing "R" between 11 : 01 and 11 : 29
changes the readout to 11 : 00.
Pressing "R" between 11 : 30 and 11 : 59
changes the readout to 12 : 00.
Push the "R" button for 3 seconds to display
a 12 or 24-hour clock.