Hyundai Matrix (2007 year). Instruction

1 CONTROLS AND EQUIPMENT

WARNING AND INDICATOR LIGHTS

SB210G1-E

SB210C1-E

It will also illuminate when the ignition

Turn Signal Indicator

SRS (Airbag) Service

key is turned to the "ON" position, and

Light

Reminder Indicator Light

then go off in a few seconds. If the TCS

indicator stays on, take your car to your

Operation of a turn signal is indicated

The SRS service reminder indicator

Hyundai authorised repairer and have

by the warning light located in the in-

(SRI) comes on and flashes for approxi-

the system checked. See section 2 for

strument cluster. If the light fails to

mately 6 seconds after the ignition key

more information about the TCS sys-

illuminate or does not flash, a malfunc-

is turned to the "ON" position or after

tem.

tion within the turn signal system is

the engine is started, after which it will

indicated.

go out.

This light also comes on when the SRS

B265C01LZ-EAT

B260U01TB-EAT

is not working properly.

Electronic Stability

Immobiliser Indicator

If the SRI does not come on, or continu-

Program Indicator Lights

ously remains on after flashing for about

Light

(Not all models)

6 seconds when you turned the ignition

This indicator light comes on for some

The electronic stability program indica-

key to the "ON" position or started the

seconds after the ignition key is turned

tors change operation according to the

engine, or if it comes on whilst driving,

to the "ON" position. At this time, you

ignition switch position and whether the

have the SRS inspected by an Hyundai

can start the engine. The light goes out

system is in operation or not.

authorised repairer.

after the engine is running. In case this

They will illuminate when the ignition

light goes out before you start the en-

key is turned to the "ON" position, but

B260C02E-EAT

gine, you must turn to the "LOCK"

should go out after three seconds. If the

Traction Control

position and restart the engine. In case

ESP or ESP-OFF indicator stays on,

Indicator Light

this light blinks for five seconds when

take your car to your Hyundai authorised

the ignition key is turned to "ON" posi-

(Not all models)

repairer and have the system checked.

tion, this indicates that the immobiliser

See section 2 for more information

The traction control indicator changes

system is out of order.

about the ESP.

operation according to the ignition switch

position and whether or not the system

is in operation.

fcuk-1.p65

12/27/2006, 10:12 AM

CONTROLS AND EQUIPMENT

SB210E1-E

Warning light operation

If failure of one of the circuits occurs,

Overdrive Off Indicator

the required amount of pedal effort,

The parking brake/low brake fluid level

Light (Not all models)

pedal travel and stopping distance will

warning light will be illuminated when-

be increased. Use of the gearbox is

When the overdrive (4th gear) switch is

ever the ignition switch is turned to the

recommended to assist in bringing the

turned off and the operation of overdrive

"ON" position irrespective of whether or

vehicle to rest. The vehicle must not be

(4th gear) is cancelled, the overdrive

not the parking brake is applied and

driven once brake failure has occurred

warning light (O/D OFF) will be illumi-

must be extinguished when the engine

until the system has been repaired and

nated. When the switch is at the on

starts and the parking brake released.

is functioning normally.

position, the gearbox will operate in the

If the warning light fails to extinguish or

The braking system employs a vacuum

normal fully automatic mode and the

illuminates at any other time, the ve-

servo in order that the pedal efforts are

warning light will be extinguished.

hicle must be brought to rest in a safe

reduced. Power for the servo is derived

location and the level of brake fluid in

from the engine and therefore, in the

the reservoir checked.

event of the engine stopping or the

SB210L2-E

If the fluid level is incorrect, fluid con-

vehicle being towed, pedal efforts will

Parking Brake/Low Brake

forming to DOT 3 or DOT 4 specifica-

be substantially increased.

Fluid Level Warning Light

tions should be added. If, after correct-

ing the brake fluid level, the warning

light continues to be illuminated, the

advice of the nearest Hyundai authorised

WARNING:

repairer must be sought before the ve-

In the event of problems being sus-

hicle is driven again.

pected with the braking system, the

The Hyundai Matrix is equipped with a

advice of the nearest Hyundai

diagonally split dual braking system

authorised repairer must be sought

which will ensure that in the event of

before the vehicle is driven. Driving

one of the brake circuits becoming

the vehicle with either an electrical

defective, approximately fifty per cent

or hydraulic braking system defect

of the normal braking performance will

may be dangerous, resulting in acci-

be available.

dent or personal injury.

fcuk-1.p65

12/27/2006, 10:12 AM

1 CONTROLS AND EQUIPMENT

SB210M1-E

SB210P1-E

B260B01FC-EAT

Charging System

Low Fuel Level Warning

Hatchback Door Open

Warning Light

Light

Warning Light

The charging system warning light

The low fuel warning light serves to

The hatchback door open warning light

should illuminate when the ignition

warn the driver that the remaining fuel

indicates when hatchback door open is

switch is turned to the "ON" position

quantity is approximately 9 litres and

open or is not fully closed. Ensure that

and should be extinguished when the

that the vehicle should be refuelled. If

the light has extinguished prior to driv-

engine is started. If the light fails to

the vehicle is driven for an extended

ing the vehicle.

illuminate when the ignition is turned

period with the low fuel warning light

"ON" or fails to extinguish after starting

illuminated there exists a possibility

SB2100I-E

the engine, the nearest Hyundai

that misfiring due to fuel shortage may

Door Open (Ajar) Warn-

authorised repairer should be contacted.

occur. This situation must be avoided

ing Light

If the light illuminates whilst the vehicle

to prevent damage to the catalyst oc-

The door ajar warning light indicates

is being driven, stop the vehicle as

curring.

that a door is not correctly closed.

soon as it is safe to do so and check the

Ensure that the light is extinguished

condition of the alternator drive belt. If

SB210J1-E

prior to driving the vehicle.

the belt is in place and the tension is

High Beam Indicator

satisfactory, the advice of a Hyundai

SB210K1-E

Light

authorised repairer should be sought.

Oil Pressure Warning

The high beam indicator light will illumi-

Light

nate whenever the headlights are

switched to high beam of flash position.

CAUTION:

If the drive belt (generator belt) is

CAUTION:

loose, broken, or missing whilst the

If the oil pressure light illuminates

vehicle is driving, there may be a

when the engine is running, an in-

sufficient oil pressure level for con-

serious malfunction, engine could

tinued safe operation of the engine

overheat because this belt also drives

exists. Continued operation of the

the water pump.

engine in this condition may result

in serious engine damage.

fcuk-1.p65

12/27/2006, 10:12 AM

CONTROLS AND EQUIPMENT

Under normal circumstances, the light

B260N02FC-EAT

B260P02Y-EAT

will illuminate when the ignition is turned

Malfunction Indicator

ABS Service Reminder

"on" and will be extinguished when the

Light

Indicator (SRI)

engine is started.

(Not all models)

This light illuminates when there is a

If the oil pressure warning light illumi-

malfunction of an exhaust gas related

When the key is turned to the "ON"

nates whilst the engine is running, stop

component, and the system is not func-

position, the Anti-Lock Brake System

the engine immediately and check the

tioning properly so that the exhaust gas

SRI will come on and then go off in a

engine oil level. If the level is insuffi-

regulation values are not satisfied. This

approximately seconds. If the ABS SRI

cient, add the required amount of oil as

light will illuminate when the ignition key

remains on, comes on whilst driving, or

indicated by the engine oil dipstick. If

is tuned to the "ON" position, and then

does not come on when the key is

the light fails to extinguish when the

it will go out after the engine start. If it

turned to the "ON" position, this indi-

engine is restarted, do not continue to

illuminates whilst driving, or does not

cates that there may be a problem with

operate the vehicle.

the ABS.

illuminate when the ignition key is turned

If the oil pressure light illuminates dur-

If this occurs, have your vehicle

to the "ON" position, take your car to

ing normal operation and the cause is

checked by your Hyundai authorised

your nearest Hyundai authorised re-

not an insufficient oil level, or the light

repairer as soon as possible. The nor-

pairer and have the system checked.

fails to illuminate when the ignition is

mal braking system will still be opera-

turned "on", contact the nearest Hyundai

tional, but without the assistance of the

authorised repairer before further oper-

anti-lock brake system.

ating the vehicle.

CAUTION:

If the both ABS SRI and Parking Brake/

Brake fluid level warning lights re-

main "ON" or come on whilst driving,

there may be a problem with E.B.D.

(Electronic Brake Force Distribution).

If this occurs, avoid sudden stops

and have your vehicle checked by

your Hyundai authorised repairer as

soon as possible.

fcuk-1.p65

12/27/2006, 10:12 AM

1 CONTROLS AND EQUIPMENT

B265A01FC-EAT

B260S01B-GAT

B900A01A-EAT

Fuel Filter Warning

Diesel Pre-heat

ACOUSTIC WARNING SOUND

Light (Diesel Engine)

Indicator Light

(Not all models)

(Diesel Engine)

The acoustic warning chime sounds

This light illuminates when the engine

when the tail lights are on and the door

has started and goes off after a approxi-

The indicator light illuminates amber

in driver side is open. This prevents the

mately seconds. If it lights up whilst the

when the ignition switch is placed at the

battery from discharging when the car

engine is running, it indicates that water

"ON" position. The engine can be started

is left with the tail lights on. The chime

has accumulated inside the fuel filter. If

after the pre-heat indicator light goes

sounds until the tail lights are turned off.

this happens, remove the water from

off. The illuminating time varies with the

the fuel filter. (Refer to "6-32 page")

water temperature, air temperature and

battery condition.

B270B02O-EAT

PARKING START WARNING

NOTE:

SOUND (Not all models)

If the engine were not started 10

If the vehicle is driven at 6mph(10km/h)

seconds after the preheating is com-

for more than 2~3 seconds, the warning

pleted, turn the ignition key once

chime will sound continuously when the

more to the "LOCK" position, and

parking brake engaged.

then to the "ON" position, in order to

preheat again.

fcuk-1.p65

12/27/2006, 10:12 AM

CONTROLS AND EQUIPMENT

INSTRUMENT CLUSTER

SB210S1-E

SB215A1-E

SB215B1-E

BRAKE PAD WEAR INDICATOR

FUEL GAUGE

ENGINE COOLANT TEMPERA-

The front brake disc pads are fitted with

TURE GAUGE

an audible wear indicator which will

cause a high pitched noise to be emit-

ted when the remaining amount of fric-

tion lining is below the specified value.

When the wear indicator is heard, the

brake pads should be replaced without

delay to avoid damage occurring to the

brake discs and a severe reduction in

braking efficiency.

HFC2045

The fuel gauge indicates the quantity of

HFC2101

B950A01E-EAT

fuel remaining in the fuel tank.

The engine coolant temperature gauge

REAR FOG AUDIBLE WARNING

indicates the engine coolant tempera-

SOUND

NOTE:

ture and will, under normal circum-

The rear fog audible warning chime

The fuel gauge is not intended to

stances, give an indication in the "Nor-

sounds when the rear fog lights are on

give other than an approximate indi-

mal" or centre portion of the scale.

and the door in driver side is open.

cation of the fuel level and is unsuit-

Should the indication move into the

able for the purposes of calculating

upper or "HOT" portion of the scale,

fuel consumption figures.

engine overheating is indicated. Under

these circumstances, the vehicle should

be brought to rest as soon as is safe to

do so and the engine turned off. Once

the engine has cooled somewhat, the

coolant level and the condition of the

generator/water pump drive belt should

be checked.

fcuk-1.p65

12/27/2006, 10:12 AM

1 CONTROLS AND EQUIPMENT

If the cause of the overheating cannot

SB215C1-E

SB215F1-E

be readily established, the assistance

SPEEDOMETER

TACHOMETER

of a Hyundai authorised repairer should

Petrol engine

be sought.

WARNING:

The engine cooling system is pres-

surized and removal of the radiator

cap when the engine is hot may

cause hot water and steam to be

ejected from the radiator resulting in

B300A01FC

HFC2043

burns and scalding. The radiator cap

The speedometer indicates the vehicle

Diesel engine

must only be removed when the en-

speed in both miles and kilometres per

gine has cooled. Do not add cold

hour.

water to a hot engine to avoid the

possibility of engine damage. The

use of plain water in the cooling

system is not recommended since

the aluminium components of the

cooling system require the use of a

corrosion inhibitor found in the rec-

ommended Ethylene Glycol type anti

B330A01FC

freeze solutions.

The tachometer registers the speed of

the engine in revolutions per minute

(R.P.M.).

fcuk-1.p65

12/27/2006, 10:12 AM

CONTROLS AND EQUIPMENT

B310B01FC-EAT

unction of digital odometer/

ODOMETER/TRIP ODOMETER F

Trip odometer

CAUTION:

Without Trip Computer

The maximum safe engine operating

Pushing in the reset switch when the

speed is indicated by the red zone of

ignition switch is turned "ON" will dis-

the tachometer scale. The engine

play the following sequence:

should not be operated beyond the

beginning of this zone or serious

engine damage may result.

Reset switch

B310B01FC

With Trip Computer

HFC2090

1. Odometer

The odometer records the total driving

distance in miles, and is useful for

keeping a record for maintenance inter-

vals.

Reset switch

B310B02FC

NOTE:

Any alteration of the odometer may

void your warranty coverage.

fcuk-1.p65

12/27/2006, 10:12 AM

1 CONTROLS AND EQUIPMENT

TRIP COMPUTER

B400B01FC-EAT

2,3 Trip odometer

Reset switch

(Not all models)

Records the distance of 2 trips in miles.

o The reset switch is used to zero the

TRIP A: First distance you have trav

multi-functional display mode.

eled from your origination

o Pushing in the reset switch changes

point to a first destination.

the display as follows;

TRIP B: Second distance from the

DISTANCE TO EMPTY

first destination to the final

destination.

AVERAGE SPEED

To shift from TRIP A to TRIP B, press

the reset switch. When pressed for 1

second, it will reset to 0.

DRIVE TIME

Reset switch

B310B02FC

The trip computer is the microcom-

puter-controlled driver information gauge

that displays information related to driv-

ing, such as distance to empty, aver-

age speed and drive time on the LCD.

fcuk-1.p65

12/27/2006, 10:12 AM

CONTROLS AND EQUIPMENT

1. Distance to empty

NOTE:

o Pressing the reset switch for more

o If the distance to empty is indi-

than 1 second, when the average

cated "- -", have the trip computer

speed is being displayed, clears the

Distance to empty symbol

system checked by your Hyundai

average speed to zero.

authorised repairer.

o The distance to empty can differ

3. Drive time

from the actual tripmeter accord-

ing to driving conditions.

o The distance to empty can vary

Drive time symbol

according to the driving condi-

tions, driving pattern or vehicle

Distance to empty (mile)

speed.

HFC2052

This mode indicates the estimated

2. Average speed

distance to empty from the current

fuel in the fuel tank and distance to

Drive time

empty symbol.

Average speed symbol

HFC2054

When refueling with more than 6.3

quarts, the trip computer will recog-

This mode indicates the drive time

nize refueling.

travelled since the last drive time

When the battery has been rein-

reset.

stalled after being discharged or dis-

Pressing the reset switch for more

connected, drive more than 20 miles

than 1 second, when the drive time is

for an accurate distance to empty.

being displayed, clears the drive time

Average speed (mph)

to zero.

B400B02FC

This mode indicates the average

speed travelled since the last aver-

age speed reset.

fcuk-1.p65

12/27/2006, 10:12 AM

1 CONTROLS AND EQUIPMENT

MULTI-FUNCTION SWITCH

SB220A1-E

SB220B1-E

B340C03FC-EAT

Turn Signal Operation

Lane Change Signal

Lighting Switch

To signal an intention to turn right, the

switch lever should be pressed down.

To signal an intention to turn left, the

switch lever should be pushed upwards.

In both instances, the turn signal lights

the instrument cluster warning light will

flash. Upon completion of the manoeu-

vre, the lever will, under normal circum-

stances, return to the "OFF" position.

However, if the manoeuvre involved

only a small movement of the steering

B340B01FC-D

B340C01FC-D

wheel, the signal may need to be can-

To indicate an intention to change lanes,

The vehicle sidelights and headlights

celled manually. If either turn signal

moving the lever slightly towards the

are operated by rotating the end of the

indicator flashes more rapidly than nor-

direction of the relevant turn signal will

turn signal switch barrel. To operate the

mal or refuses to flash at all, a malfunc-

cause the turn signal lights to flash.

parking lights, rotating the switch to the

tion of the turn signal system may

When the lever is released, it will return

first detent with ignition switch at the

exist.

to the "OFF" position.

"OFF" position will cause the lights to

illuminate. To operate the headlights,

the turn signal switch barrel should be

rotated to the second detent. The head-

lights will only operate when the ignition

switch is at the "ON" position. If the

ignition switch is turned to the "OFF"

position, only the parking lights will function.

NOTE:

The ignition must be in the "ON"

position to turn on the headlights.

fcuk-1.p65

12/27/2006, 10:12 AM

CONTROLS AND EQUIPMENT

WINDSCREEN WIPER/

WASHER SWITCH

SB220E1-E

SB230A1-E

Sidelight auto cut (Not all models)

Headlight Flash

o The purpose of this feature is to

prevent the battery from being dis-

charged. The system automatically

turns off the small light when the

driver removes the ignition key and

opens the driver- side door.

(1)

o With this feature, the sidelight will be

(2)

turned off automatically if the driver

(3)

parks on the side of road at night.

If necessary, to keep the lights on when

B350A01FC-D

the ignition key is removed, perform the

following :

B340E01FC-D

The windscreen wiper switch, depen-

1) Open the driver-side door.

The headlights may be flashed by pull-

dent upon model, has three operating

2) Turn the sidelights OFF and ON

ing the turn signal switch lever towards

positions.

again using the light switch on the

the steering wheel. The headlights will

steering column.

1.Intermittent wiper operation

be extinguished when the switch is

released.

(Not all models)

2.Low speed operation

3.High speed operation

SB220D1-E

High And Low Beam

NOTE:

To turn on the headlight high beams,

To prevent damage to the wiper sys-

push the lever forward (away from you).

tem, do not attempt to wipe away

For low beams, pull the lever back

heavy accumulations of snow or ice.

(toward you). The appropriate headlight

Accumulated snow and ice should

beam indicator light will come on at the

be removed manually. If there is only

a light layer of snow or ice, operate

same time.

the heater in the defrost mode to melt

the snow or ice before using the

wiper.

fcuk-1.p65

12/27/2006, 10:12 AM

1 CONTROLS AND EQUIPMENT

B350B02O-EAT

B350C02FC-DAT

NOTE:

Windscreen Washer Operation

Adjustable Intermittent Wiper

o Do not operate the washer more

than 15 seconds at a time or when

Operation

the fluid reservoir is empty.

o In icy or freezing weather, be sure

the wiper blades are not frozen to

the glass prior to operating the

wipers.

o In areas where water freezes in

winter, use windscreen washer an-

tifreeze.

Single Sweep Operation

B350B01FC-D

B350C01FC-D

To use the windshield washer, pull the

wiper/washer lever toward the steering

To use the intermittent wiper feature,

wheel.

place the wiper switch in the "INT"

position. With the switch in this posi-

Type A

tion, the interval between wipes can be

When the washer lever is operated, the

varied from approximately 1 to 18 sec-

wipers automatically make two passes

onds by turning the interval adjuster

across the windshield (If insatalled).

barrel.

Type B

To wipe off the windshield washer, you

B350B02FC-D

will have to additionally activate the

If a single wipe is desired, push the

windshield wiper.

windscreen wiper and washer control

lever upwards.

The washer continues to operate until

the lever is released.

fcuk-1.p65

12/27/2006, 10:12 AM

CONTROLS AND EQUIPMENT

HAZARD WARNING SYSTEM

HEATED REAR WINDOW

B350A01O-EAT

SB240A1-E

SB250A1-E

Hatchback Door Wiper And

Washer Switch

HFC2078-D

HFC2080-D

The hazard warning system should be

To operate the heated rear window de-

B350D01FC-D

used whenever it becomes necessary

press the switch shown. The heated

:The washer fluid will be

to stop the car in a hazardous location.

rear window will automatically turn off

sprayed onto the rear window

The hazard warning system is operated

after 20 minutes or when the ignition is

and the wiper operates whilst

by depressing the switch at which time

turned off.

the rear window wiper barrel is

all turn signal lights will flash simulta-

The system may be turned off manually

placed in this position.

neously and the turn signal warning

by depressing the switch again.

2.OFF

lights located within the instrument clus-

3.INT

:To use the intermittent wiper

ter will flash simultaneously.

feature, place the rear window

The hazard warning system may be

wiper barrel in the "INT" posi-

turned off by depressing the switch

tion.

again.

4.ON

:When the point indicates "ON",

the rear window wiper oper-

ates continuously.

fcuk-1.p65

12/27/2006, 10:12 AM

1 CONTROLS AND EQUIPMENT

FOG LIGHT SWITCH

B360B01FC-EAT

B360A01Y-GAT

NOTE:

Front Fog Light Switch

Rear Fog Light Switch

The engine must be running for the

(Not all models)

rear window defroster to operate.

CAUTION:

The inside of the rear windscreen

should never be cleaned with a hard

or sharp implement since damage to

the heating element may occur. The

glass should only be cleaned with a

soft cloth or chamois leather with the

B360A01FC-D

use only of a mild detergent or pro-

B360B01FC-D

To turn on the rear fog lights, push the

prietary glass cleaner where neces-

sary. Only horizontal movement of

To turn on the front fog lights, push the

switch. They will come on when the

the cloth should be made when clean-

switch in the "ON" position. They will

headlight switch is in the second posi-

ing the glass and care should be

come on when the headlight switch is in

tion and the key is in the "ON" position.

exercised to ensure that the heating

the first or second position.

elements are not damaged by rings

or jewellery whilst the glass is being

cleaned.

fcuk-1.p65

12/27/2006, 10:12 AM

CONTROLS AND EQUIPMENT

HEADLIGHT LEVELING DEVICE

DIGITAL CLOCK

SYSTEM

B340G01FC-EAT

B400A01A-AAT

Switch

Loading Condition

Position

Driver only

Driver + front passenger

Full passengers

(including driver)

Full passengers

(including driver) + Maximum

permissible loading

Driver

+ Maximum permis-

B340G01FC-D

HFC2091

sible loading

To adjust the headlight beam level ac-

There are three control buttons for the

cording to the number of the passen-

digital clock. Their functions are:

gers and the loading weight in the lug-

gage area, turn the beam leveling switch.

HOUR - Push "H" to advance the hour

The higher the number of the switch

indicated.

position, the lower the headlight beam

MIN - Push "M" to advance the minute

level. Always keep the headlight beam

indicated.

at the proper leveling position, or head-

RESET - Push "R" to reset minutes to

lights may dazzle other road users.

":00" to facilitate resetting the clock to

Listed below are the examples of rec-

the correct time. When this is done:

ommended switch settings. For loading

conditions other than those listed be-

Pressing "R" between 10 : 30 and 11 : 29

low, adjust the switch position so that

changes the readout to 11 : 00.

the beam level may be the nearest as

Pressing "R" between 11 : 30 and 12 : 29

the condition obtained according to the

changes the readout to 12 : 00.

list.

fcuk-1.p65

12/27/2006, 10:12 AM

1 CONTROLS AND EQUIPMENT

CIGAR LIGHTER

POWER OUTLET

SB290A02-F

B500D01FC-EAT

(Not all models)

CAUTION:

o Use the power outlet only when

the engine is running and remove

the plug from the power outlet

after using the electric device.

Using when the engine stops or

keeping the electric device with

plugged in for many hours may

cause the battery to discharge.

o Do not use the power outlet to

B420A01FC-D

connect electric accessories or

HFC2042-D

For the cigar lighter to work, the key

equipment that are not designed

must be in the "ACC" or the "ON"

These supply 12V electric power to

to operate on 12 volts.

position. To use the cigar lighter, push

operate electric accessories or equip-

o Some electronic devices can cause

the lighter all the way into its socket.

ment only when the key is in the "ON"

electronic interference when

When the element is heated, the lighter

position.

plugged into the power outlet.

will pop out into the "ready" position.

These devices may cause exces-

Do not hold the cigar lighter at the

sive audio noise and malfunctions

depressed position which may result in

in other electronic systems or de-

damage to the vehicle wiring or an

vices in your vehicle.

electrical fire. If it is necessary to re-

place the cigarette lighter, use only a

genuine Hyundai replacement part.

CAUTION:

Do not use electric accessories or

equipment other than the Hyundai

genuine parts in the socket.

fcuk-1.p65

12/27/2006, 10:12 AM

Hyundai Matrix (2007 year). Instruction - part 20