Honda Civic Coupe (2019 year). Instruction - part 40

uu

If a Tire Goes Flat

u

Temporarily Repairing a Flat Tire

*

624

Han

d

lin
g the U

n

expected

7. Plug in the kit to the accessory power 

socket.

u

Be careful not to pinch the cord in a 
door or window.

2 Accessory Power Socket P. 196

8. Start the engine.

2 Starting the Engine P. 435

u

Keep the engine running while injecting 
air.

2 Carbon Monoxide Gas P. 73

9. Turn the selector Knob to AIR.

10. Press the inflator switch to turn on the kit.

u

The compressor starts to inject air into 
the tire.

11. Inflate the tire to the specified air pressure.

1

Inflating an Under-inflated Tire

3

WARNING

Running the engine with the vehicle in an 
enclosed or even partly enclosed area can 
cause a rapid build-up of toxic carbon 
monoxide.

Breathing this colorless, odorless gas can 
cause unconsciousness and even death. 
Only run the engine to power the air 
compressor with the vehicle outdoors.

AIR Side

ON

625

uu

If a Tire Goes Flat

u

Temporarily Repairing a Flat Tire

*

Han

d

lin
g the U

n

expected

12. Turn off the kit.

u

Check the pressure gauge on the air 
compressor.

u

If overinflated, press the pressure relief 
button.

13. Unplug the kit from the accessory power 

socket.

14. Unscrew the sealant/air hose from the tire 

valve stem. Reinstall the valve cap.

15. Press the pressure relief button until the 

gauge returns to 0 psi (0 kPa).

16. Repackage and properly stow the kit.

Pressure Relief Button

626

Han

d

lin
g the U

n

expected

Engine Does Not Start

Checking the Engine

If the engine does not start, check the starter.

Starter condition

Checklist

Starter doesn’t turn or turns 
over slowly.
The battery may be dead. Check 
each of the items on the right and 
respond accordingly.

If a message To Start, Hold Remote Near Start Button appears on the driver information 
interface, or you hear beeping when you push the ENGINE START/STOP button.

2 If the Smart Entry Remote Battery is Weak P. 627

u

Make sure the smart entry remote is in its operating range.

2 ENGINE START/STOP Button Operating Range P. 161

Check the brightness of the interior lights.
Turn on the interior lights and check the brightness.

●

If the interior lights are dim or do not come on at all

2 Battery P. 592

●

If the interior lights come on normally

2  Fuses P. 641

The starter turns over normally 
but the engine doesn’t start.
There may be a problem with the 
fuse. Check each of the items on 
the right and respond accordingly.

Review the engine start procedure.
Follow its instructions, and try to start the engine again.

2  Starting the Engine P. 432, 435

Check the immobilizer system indicator.
When the immobilizer system indicator is blinking, the engine cannot be started.

2 Immobilizer System P. 153

Check the fuel level.
There should be enough fuel in the tank.

2  Fuel Gauge P. 111

Check the fuse.
Check all fuses, or have the vehicle checked by a dealer.

2 Inspecting and Changing Fuses P. 644

If the problem continues:

2 Emergency Towing P. 645

1

Checking the Engine

If you must start the vehicle immediately, use an 
assisting vehicle or booster battery to jump start it.

2 Jump Starting P. 629

Models with smart entry system

627

uu

Engine Does Not Start

u

If the Smart Entry Remote Battery is Weak

Han

d

lin
g the U

n

expected

If the Smart Entry Remote Battery is Weak

If the beeper sounds, the To Start, Hold Remote Near Start Button message 
appears on the driver information interface, and the ENGINE START/STOP button 
flashes, and the engine won’t start, start the engine as follows:

1. Touch the center of the ENGINE START/

STOP button with the H logo on the smart 
entry remote while the ENGINE START/
STOP button is flashing. The buttons on 
the smart entry remote should be facing 
you.

u

The ENGINE START/STOP button 
flashes for about 30 seconds.

2. Depress the brake pedal (continuously 

variable transmission) or clutch pedal 
(manual transmission) and press the 
ENGINE START/STOP button within 10 
seconds after the beeper sounds and the 
ENGINE START/STOP button changes 
from flashing to on.

u

If you don’t depress the pedal, the mode 
will change to ACCESSORY.

Models with smart entry system

628

uu

Engine Does Not Start

u

Emergency Engine Stop

Han

d

lin
g the U

n

expected

Emergency Engine Stop

The ENGINE START/STOP button may be used to stop the engine due to an 
emergency situation even while driving. If you must stop the engine, do either of the 
following operations:
• Press and hold the ENGINE START/STOP button for about two seconds.
• Firmly press the ENGINE START/STOP button three times.

The steering wheel will not lock. However, because turning off the engine disables 
the power assist the engine provides to the steering and braking systems, it will 
require significantly more physical effort and time to steer and slow the vehicle. Use 
both feet on the brake pedal to slow down the vehicle and stop immediately in a 
safe place. With manual transmission models you can also downshift the 
transmission to utilize engine braking.

The power mode is in ACCESSORY when the engine is stopped.
To change the mode to VEHICLE OFF, move the shift lever to 

(

P after the vehicle 

comes to a complete stop.

Then press the ENGINE START/STOP button twice without depressing the brake 
pedal.

The power mode changes to VEHICLE OFF.

Models with smart entry system

1

Emergency Engine Stop

Do not press the ENGINE START/STOP button while 
driving unless it is absolutely necessary for the engine 
to be switched off.
If you press the ENGINE START/STOP button while 
driving, the beeper sounds.

Continuously variable transmission models

Canadian continuously variable transmission models

Manual transmission models

629

Continued

Han

d

lin
g the U

n

expected

Jump Starting

Jump Starting Procedure

Turn off the power to electric devices, such as audio and lights. Turn off the engine, 
then open the hood.

1. Connect the first jumper cable to your 

vehicle’s battery + terminal.

2. Connect the other end of the first jumper 

cable to the booster battery + terminal.

u

Use a 12-volt booster battery only.

u

When using an automotive battery 
charger to boost your 12-volt battery, 
select a lower charging voltage than 15-
volt. Check the charger manual for the 
proper setting.

3. Connect the second jumper cable to the 

booster battery - terminal.

■

Jump Starting Procedure

1

Jump Starting

Securely attach the jumper cables clips so that they 
do not come off when the engine vibrates. Also be 
careful not to tangle the jumper cables or allow the 
cable ends to touch each other while attaching or 
detaching the jumper cables.

3

WARNING

A battery can explode if you do not follow 
the correct procedure, seriously injuring 
anyone nearby.

Keep all sparks, open flames, and smoking 
materials away from the battery.

Booster Battery

1.5 L engine models

2.0 L engine models

Booster Battery

uu

Jump Starting

u

Jump Starting Procedure

630

Han

d

lin
g the U

n

expected

4. Connect the other end of the second 

jumper cable to the engine mounting bolt 
as shown. Do not connect this jumper cable 
to any other part.

5. If your vehicle is connected to another 

vehicle, start the assisting vehicle’s engine 
and increase its rpm slightly.

6. Attempt to start your vehicle’s engine. If it 

turns over slowly, check that the jumper 
cables have good metal-to-metal contact.

1

Jump Starting

Battery performance degrades in cold conditions and 
may prevent the engine from starting.

1.5 L engine models

2.0 L engine models

631

uu

Jump Starting

u

Jump Starting Procedure

Han

d

lin
g the U

n

expected

Once your vehicle's engine has started, remove the jumper cables in the following 
order.

1. Disconnect the jumper cable from your vehicle's ground.
2. Disconnect the other end of the jumper cable from the booster battery - 

terminal.

3. Disconnect the jumper cable from your vehicle's battery + terminal.
4. Disconnect the other end of the jumper cable from the booster battery + 

terminal.

Have your vehicle inspected by a nearby service station or a dealer.

■

What to Do After the Engine Starts

1

What to Do After the Engine Starts

The indicators for the Vehicle Stability Assist® (VSA®) 
system, Vehicle Stability Assist® (VSA®) OFF, Low Tire 
Pressure/TPMS

*

 and Collision Mitigation Braking 

System

TM

 (CMBS

TM

)

*

 may come on after re-

connecting the battery. Drive a short distance at 
more than 12 mph (20 km/h). The indicators should 
go off. If they do not, have your vehicle checked by a 
dealer.

* Not available on all models

632

Han

d

lin
g the U

n

expected

Shift Lever Does Not Move

Follow the procedure below if you cannot move the shift lever out of the 

(

P 

position.

1. Set the parking brake.

2. Remove the key from the ignition switch.

2. Remove the built-in key from the smart 

entry remote.

3. Move the removable beverage holder tray 

rearward.

2 Front seat beverage holders P. 194

4. Wrap a cloth around the tip of a small flat-

tip screwdriver to remove the cover of the 
shift lock release slot. Put the tip of the flat-
tip screwdriver into the slot and remove it 
as shown in the image.

5. Insert the key into the shift lock release slot.
6. While pushing the key in, press the shift 

lever release button and place the shift lever 
into 

(

N.

u

The lock is now released. Have the shift 
lever checked by a dealer as soon as 
possible.

■

Releasing the Lock

Continuously variable transmission models

Slot

Cover

Models without smart entry system

Models with smart entry system

All models

Release 
Button

Shift Lock 
Release Slot

633

Continued

Han

d

lin
g the U

n

expected

Overheating

How to Handle Overheating

Overheating symptoms are as follows:
• The temperature gauge pointer is at the 

 mark or the engine suddenly loses 

power.

• Steam or spray comes out of the engine compartment.

■

First thing to do

1. Immediately park the vehicle in a safe place.
2. Turn off all accessories and turn on the hazard warning lights.

u

No steam or spray present: Keep the engine running and open the hood.

u

Steam or spray is present: Turn off the engine and wait until it subsides. 
Then open the hood.

1

How to Handle Overheating

NOTICE

Continuing to drive with the temperature gauge 
pointer at the 

 mark may damage the engine.

3

WARNING

Steam and spray from an overheated 
engine can seriously scald you.

Do not open the hood if steam is coming 
out.

H

H

uu

Overheating

u

How to Handle Overheating

634

Han

d

lin
g the U

n

expected

■

Next thing to do

1. Check that the cooling fan is operating and 

stop the engine once the temperature 
gauge pointer comes down.

u

If the cooling fan is not operating, 
immediately stop the engine.

2. Once the engine has cooled down, inspect 

the coolant level and check the cooling 
system components for leaks.

u

If the coolant level in the reserve tank is 
low, or no coolant in the tank, check that 
the radiator is cool. Cover the reserve 
tank cap with a heavy cloth and open the 
cap. Add coolant until it reaches the 
MAX mark, and put the cap back on.

■

Last thing to do

Once the engine has cooled sufficiently, restart it and check the temperature gauge.
If the temperature gauge pointer has gone down, resume driving. If it has not gone 
down, contact a dealer for repairs.

1

How to Handle Overheating

If the coolant is leaking, contact a dealer for repairs.

Use water as an emergency/temporary measure only. 
Have a dealer flush the system with proper antifreeze 
as soon as possible.

3

WARNING

Removing the reserve tank cap while the 
engine is hot can cause the coolant to spray 
out, seriously scalding you.

Always let the engine and radiator cool 
down before removing the reserve tank 
cap.

MAX

Reserve Tank

MIN

635

Han

d

lin
g the U

n

expected

Indicator, Coming On/Blinking

If the Low Oil Pressure Indicator Comes On

■

Reasons for the indicator to come on

Comes on when the engine oil pressure is low.

■

What to do as soon as the indicator comes on

1. Immediately park the vehicle on level ground in a safe place.
2. If necessary, turn the hazard warning lights on.

■

What to do after parking the vehicle

1. Stop the engine and let it sit for approximately three minutes.
2. Open the hood and check the oil level.

u

Add oil as necessary.

2 Oil Check P. 559

3. Start the engine and check the low oil pressure indicator.

u

The indicator goes off: Start driving again.

u

The indicator does not go off within 10 seconds: Immediately stop 
the engine and contact a dealer for repairs.

If the Charging System Indicator Comes On

■

Reasons for the indicator to come on

Comes on when the battery is not being charged.

■

What to do when the indicator comes on

Turn off the climate control system, rear defogger, and other electrical 
systems, and immediately contact a dealer for repairs.

1

If the Low Oil Pressure Indicator Comes On

NOTICE

Running the engine with low oil pressure can cause 
serious mechanical damage almost immediately.

1

If the Charging System Indicator Comes On

If you need to stop temporarily, do not turn off the 
engine. Restarting the engine may rapidly discharge 
the battery.

636

uu

Indicator, Coming On/Blinking

u

If the Malfunction Indicator Lamp Comes On or Blinks

Han

d

lin
g the U

n

expected

If the Malfunction Indicator Lamp Comes On or 
Blinks

■

Reasons for the indicator lamp to come on or blink

• Comes on when there is a problem with the engine emissions control 

system.

• Blinks when engine misfiring is detected.

■

What to do when the indicator lamp comes on

Avoid high speeds and immediately get your vehicle inspected at a 
dealer.

■

What to do when the indicator lamp blinks

Park the vehicle in a safe place with no flammable items and wait at least 
10 minutes or more with the engine stopped until it cools.

1

If the Malfunction Indicator Lamp Comes On or Blinks

NOTICE

If you drive with the malfunction indicator lamp on, 
the emissions control system and the engine could be 
damaged.

If the malfunction indicator lamp blinks again when 
restarting the engine, drive to the nearest dealer at 
31 mph (50 km/h) or less. Have your vehicle 
inspected.

637

uu

Indicator, Coming On/Blinking

u

If the Brake System Indicator (Red) Comes On or Blinks

Han

d

lin
g the U

n

expected

If the Brake System Indicator (Red) Comes On or 
Blinks

■

Reasons for the indicator to come on

• The brake fluid is low.
• There is a malfunction in the brake system.

■

What to do when the indicator comes on while driving

Depress the brake pedal lightly to check pedal pressure.
• If normal, check the brake fluid level the next time you stop.
• If abnormal, take immediate action. If necessary, downshift the 

transmission to slow the vehicle using engine braking.

■

Reason for the indicator to blink

• There is a problem with the electric parking brake system.

■

What to do when the indicator blinks

Avoid using the parking brake and have your vehicle checked by a dealer 
immediately.

1

If the Brake System Indicator (Red) Comes On or Blinks

Have your vehicle repaired immediately.
It is dangerous to drive with low brake fluid. If there 
is no resistance from the brake pedal, stop 
immediately in a safe place. If necessary downshift 
the gears.

If the brake system indicator and ABS indicator come 
on simultaneously, the electronic brake distribution 
system is not working. This can result in vehicle 
instability under sudden braking.
Have your vehicle inspected by a dealer immediately.

If the brake system indicator (red) blinks at the same 
time when the brake system indicator (amber) comes 
on, the parking brake may not work.
Avoid using the parking brake and have your vehicle 
checked by a dealer immediately.

2 If the Brake System Indicator (Red) Comes 

On or Blinks at the Same Time When the 
Brake System Indicator (Amber) Comes On 
P. 638

If you repeatedly operate the electric parking brake in 
a short period of time, the brake stops operating to 
prevent heating of the system and the indicator 
blinks.
It returns to its original state in approximately one 
minute.

U.S.

Canada

(Red)

638

uu

Indicator, Coming On/Blinking

u

If the Brake System Indicator (Red) Comes On or Blinks at the Same Time When the Brake System Indicator (Amber) Comes On

Han

d

lin
g the U

n

expected

If the Brake System Indicator (Red) Comes On or 
Blinks at the Same Time When the Brake System 
Indicator (Amber) Comes On

■

If the brake system indicator (red) comes on or blinks at the 

same time when the brake system indicator (amber) comes on, 
release the parking brake manually or automatically.

2 Parking Brake P. 527

•If the brake system indicator (red) continuously comes on or blinks at 

the same time when the brake system indicator (amber) comes on, 
stop the vehicle in a safe place and have it inspected by a dealer 
immediately.

u

Preventing the vehicle from moving

Move the shift lever to 

(

P.

Move the shift lever to 

(

1 or 

(

R.

•If only the brake system indicator (red) is turned off, avoid using the 

parking brake and have your vehicle checked by a dealer immediately.

1

If the Brake System Indicator (Red) Comes On or Blinks at the Same 
Time When the Brake System Indicator (Amber) Comes On

If you apply the parking brake, you may not be able 
to release it.

If the brake system indicator (red) and the brake 
system indicator (amber) come on at the same time, 
the parking brake is working.

If the brake system indicator (red) blinks at the same 
time when the brake system indicator (amber) comes 
on, the parking brake may not work because it is 
checking the system.

U.S.

Canada

(Red)

U.S.

Canada

(Amber)

Continuously variable transmission models

Manual transmission models

639

uu

Indicator, Coming On/Blinking

u

If the Electric Power Steering (EPS) System Indicator Comes On

Han

d

lin
g the U

n

expected

If the Electric Power Steering (EPS) System Indicator 
Comes On

■

Reasons for the indicator to come on

• Comes on when there is a problem with the EPS system.
• If you depress the accelerator pedal repeatedly to increase the engine 

speed while the engine is idling, the indicator comes on, and 
sometimes the steering wheel becomes harder to operate.

■

What to do when the indicator comes on

Stop the vehicle in a safe place and restart the engine.
If the indicator comes on and stays on, immediately have your vehicle 
inspected by a dealer.