Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 711

 

  Index      Chrysler     Chrysler 300/300 Touring/300C, Dodge Magnum - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  709  710  711  712   ..

 

 

Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 711

 

 

4.

VERIFY WIRING

Turn the ignition off.

Inspect the driver and passenger seat wiring for Seat Position Sensors.

Are Seat Position Sensor(s) present?

Yes

>>

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.

WARNING: If the Occupant Classification Module (OCM) is dropped at any time, it must be replaced. Failure
to take the proper precautions can result in accidental airbag deployment and personal injury or death.Re-
place the OCM in accordance with the Service Information.

Perform the OCS VERIFICATION TEST-VER. 1

No

>> Perform the OCS VERIFICATION TEST-VER. 1 Diagnostic Test

5.

CHECK FOR ACTIVE INTERNAL FAULTS, IGNITION FAULTS, AND BATTERY FAULTS IN THE OCCUPANT
RESTRAINT CONTROLLER (ORC)

With the scan tool, read Occupant Restraint Controller (ORC) DTCs.

Does the scan tool display any active DTCs relating to internal faults, ignition faults, or battery faults?

Yes

>> Diagnose and repair the DTCs. Refer to the Table of Contents in this Section for a complete list of

symptoms.

No

>> Go To 6

6.

VERIFY THAT B1B91-DRIVER SEAT TRACK POSITION SENSOR CONFIGURATION MISMATCH IS ACTIVE

With the scan tool, erase ORC DTCs.

Turn the ignition off, wait 10 seconds and then turn the ignition on.

Wait 2 minutes, and then with the scan tool, read ORC DTCs.

Does the scan tool display active: B1B91-DRIVER SEAT TRACK POSITION SENSOR CONFIGURATION
MISMATCH?

Yes

>> Go To 7

No

>> Perform the ORC VERIFICATION TEST-VER. 1

7.

VERIFY WIRING

Turn the ignition off.

Inspect the driver and passenger seat wiring for Seat Position Sensors.

Are Seat Position Sensor(s) present?

Yes

>>

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.

WARNING: If the Occupant Restraint Controller (ORC) is dropped at any time, it must be replaced. Failure to
take the proper precautions can result in accidental airbag deployment and personal injury or death.Replace
the ORC in accordance with the Service Information.

Perform the ORC VERIFICATION TEST-VER. 1

No

>> Perform the ORC VERIFICATION TEST-VER. 1

8O - 250

RESTRAINTS - ELECTRICAL DIAGNOSTICS

LX

B1BA5-AIRBAG SQUIB CONFIGURATION MISMATCH

For a complete wiring diagram Refer to Section 8W.

When Monitored:
With the ignition on.

Set Condition:
If an Occupant Restraint Controller (ORC) configured for vehicles without side airbags is installed in a vehicle
with side airbags.

Possible Causes

POWERTRAIN CONTROL MODULE (PCM)

OCCUPANT RESTRAINT CONTROLLER (ORC)

Diagnostic Test

1.

VERIFY THAT DTC B1BA5 AIRBAG SQUIB CONFIGURATION MISMATCH IS ACTIVE

NOTE: Ensure the battery is fully charged.

NOTE: When reconnecting Airbag system components, the ignition must be turned off and the battery must
be disconnected.
Turn the ignition on.

With the scan tool, read ORC DTCs.

Does the scan tool display active: B1BA5 AIRBAG SQUIB CONFIGURATION MISMATCH?

Yes

>> Go To 2

No

>> Go To 5

2.

VERIFY THAT VEHICLE IS EQUIPPED WITH OCCUPANT CLASSIFICATION SYSTEM (OCS)

Vehicles equipped with a Occupant Classification System (OCS) will have a Passenger Airbag On/Off Indicator
Lamp mounted to the dashboard. Verify that the vehicle is equipped with this indicator lamp.

With the scan tool, select ECU View and check that the Occupant Classification Module (OCM) is active on the bus.

Is the vehicle equipped with an Occupant Classification System (OCS)?

Yes

>> Go To 3

No

>> Replace the ORC in accordance with Service Information.

Perform ORC VERIFICATION TEST - VER 1.

3.

CHECK ORC PART NUMBER WITH SCAN TOOL

With the scan tool, select ECU View, select ORC, select ECU Details, and read the ORC part number.

Is the part number correct for the vehicle?

Yes

>> Go To 4

No

>> Replace the ORC in accordance with Service Information.

Perform ORC VERIFICATION TEST - VER 1.

LX

RESTRAINTS - ELECTRICAL DIAGNOSTICS

8O - 251

4.

CHECK VIN WITH SCAN TOOL

With the scan tool, read the VIN.

Is the correct VIN displayed?

Yes

>> Replace the ORC in accordance with Service Information.

Perform ORC VERIFICATION TEST - VER 1.

No

>> Replace the Powertrain Control Module (PCM) in accordance with Service Information.

Perform ORC VERIFICATION TEST - VER 1.

5.

TEST FOR INTERMITTENT CONDITION

With the scan tool, record and erase all DTCs from all Airbag modules.

If any ACTIVE codes are present they must be resolved before diagnosing any stored codes.

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.

Look for chafed, pierced, pinched, or partially broken wires and broken, bent, pushed out, spread, corroded, or con-
taminated terminals.

The following additional checks may assist you in identifying a possible intermittent problem.

Reconnect any disconnected components and harness connector.

WARNING: To avoid personal injury or death, turn the ignition on, then reconnect the battery.
With the scan tool, monitor active codes as you work through the following steps.

WARNING: To avoid personal injury or death, maintain a safe distance from all airbags while performing the
following steps.
Wiggle the wiring harness and connectors of the related airbag circuit or component.

If codes are related to the Driver Airbag circuits, rotate the steering wheel from stop to stop.

If only stored codes return, continue the test until the problem area has been isolated.

In the previous steps you have attempted to recreate the conditions responsible for setting the active DTC in ques-
tion.

Does the scan tool display any ACTIVE DTCs?

Yes

>> Select appropriate symptom from Symptom List.

No

>> No problem found at this time. Erase all codes before returning vehicle to customer.

B1BA6-OCCUPANT CLASSIFICATION UNDETERMINED

For a complete wiring diagram Refer to Section 8W.

When Monitored:
With the ignition on or off.

Set Condition:
Because other DTCs have made occupant detection impossible. This DTC will set in addition to all sensor and
module DTCs and will be erased when the repairs are completed.

Refer to B1BA7-OCCUPANT CLASSIFICATION SYSTEM VERIFICATION REQUIRED for the diagnostic test pro-
cedure.

8O - 252

RESTRAINTS - ELECTRICAL DIAGNOSTICS

LX

B1BA7-OCCUPANT CLASSIFICATION SYSTEM VERIFICATION REQUIRED

OCS SEAT WEIGHTS MRL #9077

LX

RESTRAINTS - ELECTRICAL DIAGNOSTICS

8O - 253

 

 

 

 

 

 

 

Content   ..  709  710  711  712   ..