SsangYong: Engine Euro 4. Manual - part 103

CHANGED BY

EFFECTIVE DATE

AFFECTED VIN

8

DIAGNOSIS

CCCS

GND

GND

12 V

GND

GND

GND

GND

GND

12 V

GND

-

1. All door knob lock relays other than the driver

side

The value appears only when the relay is con-
nected

2. Ground level when operating

3. Battery level during normal

1. All door knob unlock relays

   (Cannot operate with driver side lock knob)

The value appears only when the relay is con-
nected

2. Ground level when operating

3. Battery level when not operating

1. Windshield wiper operation switch

When equipped with the rain sensor, no in-
puts are transmitted to STICS

2. Battery level when operating

3. Ground level when not operating

1. Siren operation signal

2. Ground level when operating

3. Battery level when not operating

1. Parking brake headlamp

2. Ground level when operating

3. Battery level when not operating

1. Buzzer operation

2. Ground level when operating

3. Battery level when not operating

1. Door open and driving warning

2. Ground level when operating

3. Battery level when not operating

1. Heating grid operation relay drive output

2. Ground level when operating

3. Battery level when not operating

1. Heating grid operation relay drive output

(Operates when in armed mode)

2. Ground level when operating

3. Battery level when not operating

1. Tail lamp relay drive output

(Blink once when operating the tail lamp
switch)

2. Ground level when operating

3. Battery level when not operating

-

1.Driver side foot lamp

(Operating value delays as per dimming time)

2. Pulse signal between the battery and ground

when operating.

→ Refer to operation signal STICS specifi-

cations

38

39

40

41

42

43

44

45

46

47

48

49

All door lock other
than driver side

Driver side door
unlock relay

Windshield wiper
relay

Siren operation

Parking brake
headlamp

Buzzer operation

Door open
headlamp

Heating grid relay

Hazard warning
relay

Tail lamp relay

-

Front left foot lamp

Not

operating

Not

operating

Not

operating

Not

operating

Not

operating

Not

operating

Not

operating

Not

operating

Operating

Not

operating

-

Not

operating

12 V

12 V

GND

12 V

12 V

12 V

12 V

12 V

GND

12 V

-

Operating

Operating

Operating

Operating

Operating

Operating

Operating

Operating

Not

operating

Operating

-

Operating

Output

Output

Output

Output

Output

Output

Output

Output

Output

Output

-

Output

No.

Sensor value item

Information

Help

Input/

Output

CHANGED BY

EFFECTIVE DATE

AFFECTED VIN

9

DIAGNOSIS

CCCS

BRAKE

ECU

TCU

A/BAG

TC

RK-STICS

FFH

R/SENSOR

FA

T

C

TGS-LEVER

P/TRUNK

CCCS

1. Passenger side foot lamp

(Operating value delays as per dimming time)

2. Pulse signal between the battery and ground

when operating.

→ Refer to operation signal STICS specifi-

cations

1. Rear door foot lamp

(Operating value delays as per dimming time)

2. Pulse signal between the battery and ground

when operating.

→ Refer to operation signal STICS specifi-

cations

1. Room lamp

(Operating value delays as per dimming time)

2. Pulse signal between the battery and ground

when operating.

→ Refer to operation signal STICS specifi-

cations

1. Brightness changes according to the rheostat

volume when the tail lamp is turned on

2. Pulse signal between the battery and ground

when operating. Pulse width may change by
20% ~ 100% (based on GND).

→ Refer to operation signal STICS specifi-

cations

1. Fixed rate dimming light

(Operating value changes periodically)

2. Pulse signal between the battery and ground

when operating. Pulse width maintains 50%
of the duty rate.

→ Refer to operation signal STICS specifi-

cations

-

-

-

Controls the dimming by 20 ~ 100%

1. Windshield wiper volume value: 0 ~ 10 k

Ω

→ Value between 0 ~ Vcc

For the rain sensor equipped vehicle, no in-
puts are transmitted to STICS

1. The unit time of the windshield wiper inter-

mittent intervals

For the rain sensor equipped vehicle, no in-
puts are transmitted to STICS

50

51

52

53

54

55

56

57

58

59

60

61

Front right foot
lamp

Rear foot lamp

Room lamp

Rheostat lamp

Fixed rate dimming
control

-

-

-

Current vehicle
speed

Dimming control

Windshield wiper
operating resis-
tance stages

Intermittent time

Not

operating

Not

operating

Not

operating

Not

operating

Not

operating

-

-

-

-

-

-

Operating

Operating

Operating

Operating

Operating

-

-

-

Output

Output

Output

Output

Output

-

-

-

Output

Output

Output

Output

No.

Sensor value item

Information

Help

Input/

Output

-

-

-

A km/h

A %

A kohn

A 

*

 10 ms

CHANGED BY

EFFECTIVE DATE

AFFECTED VIN

10

DIAGNOSIS

CCCS

DIAGNOSIS OF MAIN DICS

Code

Malfunction

Help

- The inputs have more than 30 edge hall pulses under the limiter switch off recog-

nized as the upper position condition during the power window up or down outputs

- Check the limiter switch
- Check the sensor values

• Power window anti-trap (DICS-Main: No. 50)
• Power window limiter switch (DICS-Main: No. 56)

- When the power window motor is under load, the auto-stop orders the power win-

dow to disengage auto-up function regardless ON or OFF inputs (no pulse signals)

- No inputs of hall pulse exceeding 700 milliseconds during the power window mo-

tor down outputs under the limiter switch OFF (the upper position of the window)
conditions or no inputs of pulse exceeding 100 milliseconds during the up outputs
under the limit switch ON (the lowest position of the window) conditions.

- Replace the power window motor

- Check the driver side door actuator
- Check the sensor value

• Key lock (DICS-Main: No. 32)

- Check the driver side door actuator

• Check the method of the actuator operation

- Check the sensor value

• Key unlock (DICS-Main: No. 31)

- When the outside rearview mirror has no UP or DOWN sensor values, DICS-Main

recognizes and disables the vehicle memory function. However, when the memory
input has detected, it means the sensor is open-circuited or has different mirror
has been installed.

- Check the outside rearview mirror UP or DOWN sensor wires
- Measure sensor values and check the accordance position

• Internal DOWN switch of the outside rearview mirror (DICS-Main: No. 21)
• Internal UP switch of the outside rearview mirror (DICSMain:No. 22)
• Internal DOWN motor of the outside rearview mirror (DICS-Main: No. 37)
• Internal UP motor of the outside rearview mirror (DICSMain:No. 38)
• Internal sensor of the outside rearview mirror (DICS-Main: No. 49)
• Internal operation of the outside rearview mirror (DICSMain:No. 53)

- When the outside rearview mirror has no LEFT or RIGHT sensor values, DICS-Main

recognizes and disables the vehicle memory function. However, when the memory
input has detected, it means the sensor is open-circuited or has different mirror
has been installed.

- Check the outside rearview mirror LEFT or RIGHT sensor wires.
- Measure the sensor values and check the relevant position

• Internal RIGHT switch of the outside rearview mirror (DICS-Main: No. 19)
• Internal LEFT switch of the outside rearview mirror (DICSMain: No. 20)
• Internal RIGHT motor of the outside rearview mirror (DICSMain: No. 35)
• nternal LEFT motor of the outside rearview mirror (DICSMain: No. 36)
• Internal sensor of the outside rearview mirror (DICS-Main: No. 49)
• Internal operation of the outside rearview mirror (DICSMain: No. 53)

- The window does not lower to the certain range when autostop is detected during

the driver side window auto-up operation.

- Check the power window motor wires
- Measure the sensor values and check the relevant position

• Power window anti-trap (DICS-Main: No. 50)
• Replace the power window motor

0 X 21

0 X 22

0 X 23

0 X 24

0 X 25

0 X 26

0 X 27

Power window
limiter switch open

Defective power
window motor hall
sensor

Inactive key door lock
actuator

Inactive key door
unlock actuator

Memory switch input
during no mirror UP
or DN input

Memory switch input
during no mirror LT or
RT input

Defective auto-stop

CHANGED BY

EFFECTIVE DATE

AFFECTED VIN

11

DIAGNOSIS

CCCS

BRAKE

ECU

TCU

A/BAG

TC

RK-STICS

FFH

R/SENSOR

FA

T

C

TGS-LEVER

P/TRUNK

CCCS

1. Switch the input signal to raise the rear left

window

2. Internal input

3. Input signal transmits to STICS through CAN

1. Switch the input signal to lower the passenger's

window

2. Internal input

3. Input signal transmits to DICS-Sub through

CAN

1. Switch the input signal to lower the passenger's

window automatically

2. Internal input

3. Input signal transmits to DICS-Sub through

CAN

1. Switch the input signal to raise the passenger's

window

2. Internal input

3. Input signal transmits to DICS-Sub through

CAN

1. Switch the input signal to lower the driver side

window

2. Internal input

3. DICS-Main has direct drive circuit

1. Switch the input signal to lower the driver

side window automatically

2. Internal input

3. MICOM drives based on the signal

1. Switch input signal to raise the driver side window

2. Internal input

3. DICS-Main has direct drive circuit

1. Switch input signal to raise the driver side

window automatically (operates only when
the engine is running)

2. Internal input

3. MICOM drives based on the signal

4. When the obstruction is found (detects as hall

pulse signal), the auto-stop engages the win-
dow to be lowered by 150 mm from its position

1. Input signal of the motor protection is en-

gaged by cutting the motor output when de-
tects the increasing in currency when the
motor is stopped at the lowest position of the
driver side's window

2. Internal input

1. Input signal coming from STICS

2. Outside rearview mirrors will not fold when

the signal comes on while outside rearview
mirror is folding.

1

2

3

4

5

6

7

8

9

10

Rear left P/WDW
UP S/W

Front right P/WDW
DN S/W

Front right P/WDW
AUTO DN S/W

Front right P/WDW
UP S/W

Front left P/WDW
DN S/W

Front left P/WDW
AUTO DN S/W

Front left P/WDW
UP S/W

Front left P/WDW
AUTO UP S/W

Detecting driver's
P/WDW detention

Detecting 3 km/h
of vehicle speed

Not

operating

Not

operating

Not

detected

Not

operating

Not

operating

Not

detected

Not

operating

Not

operating

Not

detected

Not

detected

Operating

Operating

Detected

Operating

Operating

Detected

Operating

Operating

Detected

Detected

Input

Input

Input

Input

Input

Input

Input

Input

Input

Input

No.

Sensor value item

Information

Help

Input/

Output

Main DICS Input/Output Monitoring Data