Renault Megane (2022 year). Manual in english - page 5

 

  Index      Manuals     Renault Megane (2022 year). Manual in english

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

 

 

Content      ..     3      4      5      6     ..

 

 

 

Renault Megane (2022 year). Manual in english - page 5

 

 

TRIP COMPUTER: general information (4/4)
Selections
Interpreting some of the
(the display depends on the vehicle
values displayed after
equipment and country)
resetting
a) Trip log, operating faults and infor-
The values showing average fuel con-
mation message readout;
sumption, range and average speed
will become more stable and reliable
b) current fuel consumption and aver-
the further you travel after pressing the
age fuel consumption;
reset button.
c) trip mileage recorder and average
For the first few miles after pressing the
speed;
reset key you will notice that the range
d) Reset the tyre pressure;
increases as you travel. This range
e) set the time;
takes into account the average fuel con-
sumption since the last time the reset
f) distance before service;
4
button was pressed. However, average
- Distance before service;
consumption can decrease when:
Resetting the trip mileage
- Mileage before oil change.
- the vehicle stops accelerating;
recorder and journey
g) Estimated range with remaining rea-
- the engine reaches its operating
parameters (reset button)
gent.
temperature (if the engine was cold
With one of the trip parameters se-
when the reset key was pressed);
lected as the display, press and hold
- when driving from an urban area
the
4 switch “OK” until the display
onto the open road.
resets to zero.
Automatic resetting of the
journey parameters
Resetting occurs automatically when
the maximum value of any of the pa-
rameters is exceeded.
1.84
TRIP COMPUTER AND WARNING SYSTEM: journey parameters (1/4)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Examples of selections
Interpreting the display selected
a) Trip log.
Successive display:
Vehicle Systems OK
- information messages (passenger airbag OFF etc.);
- operating fault messages (Check injection etc.).
b) Current fuel consumption.
This value is displayed after a speed of approximately 20 mph (30 km/h) is
7.4 L/100
reached.
Average fuel consumption since the last reset.
The value is displayed after having travelled at least 400 metres since the last
5.8 L/100
reset.
c) Trip mileage recorder: distance travelled since the last reset.
112,4 km
Average speed since the last reset.
123.4 km/h
The value is displayed after driving 400 metres.
1.85
TRIP COMPUTER AND WARNING SYSTEM: journey parameters (2/4)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Examples of selections
Interpreting the display selected
Tyre pressure init.
d) Reset the tyre pressure.
long press
➥ 2.32
e) Setting the time.
16:30
➥ 1.97
1.86
TRIP COMPUTER AND WARNING SYSTEM: journey parameters (3/4)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Examples of selections
Interpreting the display selected
On-board computer with mileage-
before-service message
f)
Service distance.
Mileage before service
Service in
With the ignition on and engine not running, access the “Mileage
25 000 km/12 months
before service” information. When the distance value approaches its
limit, there are several possible scenarios:
- If the range is less than 930 miles (1,500 km) or one month: the
message “Service due” is displayed accompanied by the nearest
Service due in
term (distance or time);
300 km / 24 days
- range equal to 0 miles (0 km) or date of service reached: the mes-
sage “Service Required” is displayed accompanied by the warning
The vehicle requires a service as soon as possible.
Service Required
Reset: to reset the distance before the next service, press and hold the OK button for approximately 10 seconds until the dis-
play shows the mileage before service permanently.
Note: if a service is performed without changing the engine oil, only the mileage before the next service should be reset. In the
event of an oil change, both the distance before the next service and the next oil change should be reset.
1.87
TRIP COMPUTER AND WARNING SYSTEM: journey parameters (4/4)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Examples of selections
Interpreting the display selected
On-board computer with distance
before next service message (cntd.)
f) Service distance.
Oil change in
Mileage before service
With the ignition on and the engine not running, access the mileage
25 000 km/24 months
information to display the mileage before the next oil change.
Depending on the vehicle, the mileage before an oil change varies according to the driving style (frequent driving at low speed,
door-to-door journeys, extensive use at idling speed, towing a trailer, etc.). The distance remaining until the next oil change can
therefore decrease more quickly in some cases than the actual distance travelled.
Reset: to reset the distance before the next service, press and hold the OK button for approximately 10 seconds until the display
shows the mileage before oil change permanently.
Note: if a service is performed without changing the engine oil, only the mileage before the next service should be reset. In the
event of an oil change, both the distance before the next service and the next oil change should be reset.
Top Up AdBlue before 2400 km
g) Estimated range with remaining reagent.
1.88
TRIP COMPUTER AND WARNING SYSTEM: information messages
These can help in the vehicle starting phase, or give information about a selection or a driving status.
Examples of information messages are given in the following pages.
Examples of messages
Interpreting the display selected
“Parking Brake ON”
Indicates that the parking brake has been applied.
Turn the steering wheel slightly whilst pressing the vehicle start button to unlock the steer-
“Turn Steering Wheel + START”
ing column.
“Vehicle Checks in Progress”
Displayed with the ignition on when the vehicle is running self-diagnostics.
1.89
TRIP COMPUTER AND WARNING SYSTEM: operating fault messages
soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle.
They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The
warning light stays on. Examples of operating fault messages are given in the following pages.
Examples of messages
Interpreting the display selected
“Clean Diesel Filter”
Indicates the presence of water in the diesel filter; contact an approved Dealer
as soon as possible.
“Check vehicle”
Indicates a fault in one of the pedal sensors, battery management system or oil
level sensor.
“WARNING: Check Airbag”
Indicates a fault in the restraint system in addition to the seat belts. In the event
of an accident, it is possible that they may not be triggered.
“Check Anti- Pollution System”
- Indicates a fault in the vehicle’s particle filter system.
- Indicates a fault in the emissions reduction system when it is accompanied
by the
warning light. ➥ 1.119.
1.90
TRIP COMPUTER AND WARNING SYSTEM: warning message
These appear with the® warning light and require you to stop immediately, for your own safety, as soon as traf-
fic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer.
Examples of warning messages are given in the following pages. Note: the messages appear on the display either individually
or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.
Examples of messages
Interpreting the display selected
“WARNING: Engine Failure Risk”
Indicates an injection fault, the vehicle’s engine has overheated or there is a
serious engine fault.
“WARNING: Braking System”
Indicates a fault in the braking system.
“WARNING: Electric System”
Indicates a fault in the vehicle battery charging circuit (alternator etc.).
“Puncture”
Indicates that at least one wheel is punctured or severely underinflated.
1.91
VEHICLE SETTINGS CUSTOMISATION MENU (1/3)
Adjusting the settings
d) “Welcome”:
- External welcome;
Select a menu then the function to be
- Automatic fold-out of mirrors;
1
modified (the display depends on the
- Interior welcome;
vehicle equipment and country):
- Courtesy light auto mode.
a) “Driving”:
Depending on the function, select:
- Indicator volume.
- “ON” or “OFF” to activate or deacti-
b) “Access”:
vate,
- Unlocking the driver’s door;
or
- Lock doors during driving;
- a duration to adjust the time the lights
- Opening/closing in hands-free
are switched on (e.g. for the “Follow-
mode;
me-home lighting” function).
- Remote locking/Approach unlock-
Please refer to the multimedia instruc-
ing;
tions for further information.
- Distance locking sound;
- Silent mode;
Depending on the vehicle equipment,
- Automatic locking.
this function allows you to activate/de-
c) “Wiping and lighting”:
activate and adjust some of the vehi-
- Follow-me-home lighting;
cle’s functions.
- Wiping in reverse;
- Automatic front wiping;
Vehicles fitted with a
– Wipe after wash.
multimedia screen 1
Accessing the settings menu
Refer to the multimedia instructions for
information on accessing the various
settings.
For safety reasons, carry
out any adjustments when
the vehicle is stationary.
1.92
VEHICLE SETTINGS CUSTOMISATION MENU (2/3)
Adjusting the settings
d) “DRIVING ASSIST”:
2
- Lane departure warning sensitiv-
Navigate using the 4 or 5 control to
ity;
select the function to be modified and
- Lane departure warning vibration;
press 6 “OK” to confirm (display may
- Lane keeping assist sensitivity;
vary according to vehicle equipment
- Blind spot warning;
and country):
- Fatigue warning;
a) “DASHBOARD”:
- Active braking;
- Language;
- Overspeed warning;
- Unit;
- Distance warning.
4
- Style;
3
e) “LIGHTING”:
- Colour.
- Courtesy light auto mode;
b) “VEHICLE”:
- Automatic follow-me-home light-
- Rear windscreen wiping in re-
ing;
6
verse gear;
5
- Follow-me-home lighting: XX sec-
- Automatic windscreen wiping;
onds.
Vehicles not fitted with a
- Front/rear drip wiping function;
f)
“ACCESS”:
multimedia screen
- External welcome;
- Lock doors during driving;
- Free-wheel in ECO mode;
- Opening/closing in hands-free
Accessing the settings menu on
- Indicator volume.
mode;
display 2
c) “PARKING ASSIST”:
- Unlocking the driver’s door only;
With the vehicle stopped, press the 3
- Beep sound volume;
- Automatic re-locking;
switch as many times as required to
- front obstacle detection;
- Silent locking;
reach the “Vehicle” tab. Press repeat-
- side obstacle detection;
- Automatic opening/closing;
edly on the 4 or 5 switch to access the
– rear obstacle detection.
- Automatic deployment of door
“Settings” menu, then confirm by press-
mirrors.
ing 6 “OK".
g) “RESET”.
1.93
VEHICLE SETTINGS CUSTOMISATION MENU (3/3)
=
function activated
<
function deactivated
Once a line has been selected, press 6
“OK" to adjust the function.
If you select either “PARKING ASSIST”
then “VOLUME”, or “DASHBOARD”
then “LANGUAGE”, you will have to
3
4
make a further selection (sound volume
of the parking distance control or in-
strument panel language). In this case,
make your selection and confirm it by
pressing 6 “OK”, the selected value is
6
5
shown by a =
in front of the line.
To exit the menu, press the 4 or 5
switch to access “BACK” and confirm
by pressing 6 “OK”. It may be neces-
sary to carry out this operation more
than once.
The vehicle settings personalisation
menu cannot be used when driv-
ing. At a speed exceeding 12 mph
(20 km/h), the instrument panel dis-
play switches automatically back to
trip computer and warning system
mode.
1.94
STEERING WHEEL
Activating the function
With the ignition on, press the switch 2,
the warning light integrated in the
3
4
switch lights up.
Deactivating the function
1
- Automatic:
The function switches off automatically
after the regulation phase of approxi-
mately 30 minutes. The switch 2 warn-
ing light stays on.
2
Note: If the function has switched off
automatically, press the switch 2 twice
to reactivate it.
If switch 2 is not pressed again, the
Adjusting the steering wheel
Steering wheel heating
function will be reactivated the next
height and depth
(depending on the vehicle)
time the ignition is switched on.
Lower the lever 1 and position the
This function heats the steering wheel
- Manually:
steering wheel in the required position.
in areas 3 and 4.
To deactivate the function during the re-
gulation phase, press the switch 2. The
Then, raise the lever fully, beyond the
Operating principle
indicator light in the switch 2 goes out.
point of resistance to lock the steering
When the temperature is reached, the
wheel.
function regulates the temperature of
Make sure that the steering wheel is
the heated areas for approximately
correctly locked.
30 minutes and then switches off auto-
matically.
For safety reasons, only
adjust the steering wheel
when the vehicle is statio-
nary.
1.95
POWER-ASSISTED STEERING
Never drive with an inadequately
Note: the power-assisted steering de-
charged battery.
pends on the driving mode selected in
the “MULTI-SENSE” menu (➥ 3.2).
Variable power-assisted
steering
The variable power assisted steering
system is equipped with an electronic
control system which alters the level of
assistance to suit the vehicle speed.
Steering is made easier during parking
manoeuvres (for added comfort) while
the force needed to steer increases
progressively as the speed rises (for
enhanced safety at high speeds).
Special feature of Stop and
Never leave the steering wheel at
Start
full lock while stationary.
Depending on the vehicle, when the
engine switches to standby, the steer-
ing assistance may no longer be opera-
tional. In this case it returns to its origi-
With the engine switched off, or if
nal state when the engine is restarted
there is a system fault, it is still pos-
or when the speed moves above
sible to turn the steering wheel. The
0.62 mph (1 km/h) (hill, slope, etc.).
force required will be greater.
Do not switch off the engine
when driving downhill and,
as a general rule, when
driving (the power-assisted
steering and brake cannot operate
normally).
1.96
CLOCK AND EXTERIOR TEMPERATURE (1/2)
1
6
2
3
5
4
Vehicles fitted with a multimedia
Vehicles not fitted with a multimedia
Set the hour using control 3 or 4, then
screen
screen
press 5 “OK” to confirm.
The time and exterior temperature are
Press the switch 2 as many times as re-
Set the minutes using control 3 or 4,
displayed on the multimedia screen 1.
quired to reach the “Vehicle” tab.
then press 5 “OK” to confirm.
Refer to the multimedia instructions.
Repeatedly press control 3 or 4 to set
the 6 clock.
Press and hold switch 5 “OK” until the
time display flashes.
1.97
CLOCK AND EXTERIOR TEMPERATURE (2/2)
External temperature
indicator
Depending on the vehicle, If the
electrical supply is cut (battery dis-
Special note:
connected, broken supply wire,
When the external temperature is be-
etc.), the clock will automatically
tween -3°C and +3°C, the °C figures
go back to the right time after a few
flash (indicates risk of ice).
minutes once the system is capable
of receiving information GPS.
External temperature
indicator
As ice formation is related
to climatic exposure, local
air humidity and temperature, the
external temperature alone is not
sufficient to detect ice.
1.98
REAR VIEW MIRRORS (1/2)
Folding rear view mirrors
Welcome and goodbye function
The door mirrors automatically fold in
Refer to the multimedia instructions to
when the vehicle is locked (switch 3 in
access the welcome and goodbye func-
position B).
tion.
In any case, you can make the door
Activate or deactivate the function by
mirrors fold in (switch 3 in position C) or
selecting (ON or OFF).
fold out (switch 3 in position A).
Depending on the selected choice, the
Automatic mode is then deactivated.
door mirrors will fold out:
1
2
To reactivate it, set the switch 3 to po-
- when the ignition is next switched on
sition B.
(function deactivated);
A
- when the card is detected or the ve-
3
hicle is unlocked (function activated).
B C
Exterior rear view mirrors
Adjustment
Select the rear view mirror using
switch 2, then use button 1 to adjust it
to the desired position.
Heated door mirrors
Mirror de-icing is carried out at the same
Objects observed in the
time as rear screen de-icing. ➥ 3.8.
door mirror glass are ac-
tually closer than they
appear. For your safety,
take this into account in order to
correctly assess the distance before
For safety reasons, carry
any manoeuvre.
out any adjustments when
the vehicle is not being
driven.
1.99
REAR VIEW MIRRORS (2/2)
5
4
Interior rear view mirror
Rear view mirror with lever 4
When driving at night, to avoid being
dazzled by the headlights of the vehicle
behind, depress the little lever located
behind rear view mirror 4.
Rear view mirror without lever 4
The rear-view mirror automatically
darkens when you are being followed
by a vehicle using main beam head-
lights or in very bright lighting.
The front passenger airbag acti-
vation/deactivation information is
shown on the display 5 ➥ 1.58.
1.100
HEADLIGHT BEAM ADJUSTMENT
Examples of positions for adjusting
controlA according to the load
5 doors
Estate
4 doors
Driver alone or with front
A
0
0
0
passenger
All seats occupied
1
1
1
On vehicles fitted with this function,
control A allows you to adjust the height
Driver with passengers and
of the beams according to the load.
luggage (or load) reaching the
3
3
3
maximum permissible all-up
Turn control A downwards to lower the
weight
headlights and upwards to raise them.
Driver without passengers and
luggage (or load) reaching the
3 or 4*
4
4
maximum permissible all-up
weight
* depending on the vehicle
For vehicles not fitted with a con-
trol A, the headlight adjustment is
automatic, depending on the vehi-
The table below gives some examples. In all cases, adjust control A according to
cle load.
the vehicle load so that the road can be seen and other drivers are not dazzled.
1.101
EXTERIOR LIGHTING AND SIGNALS (1/6)
Depending on the vehicle, the dipped
1
beam headlights will appear automati-
1
cally after several sweeps of the wind-
2
screen wiper blades.
3
Side lights
Dipped beam
š
k
headlights
Turn ring 2 until the symbol is
Manual operation
opposite mark 3.
This indicator light on the instrument
Turn ring 2 until the symbol is opposite
panel comes on.
mark 3. This indicator light on the in-
strument panel comes on.
Daytime running lights
Automatic operation
function
(depending on the vehicle)
The daytime running lights come on
Turn ring 2 until the AUTO symbol is op-
automatically with no action on stalk 1
posite mark 3: with the engine running,
when the engine is started, and they go
the dipped beam headlights switch on
off once the engine is switched off.
or off automatically depending on the
brightness of the light outside, without
any action on stalk 1.
1.102
EXTERIOR LIGHTING AND SIGNALS (2/6)
During deactivation of the main beam
The main beam headlights come on au-
1
headlights, the dipped beam headlights
tomatically if:
return to their original position.
- exterior light is weak;
2
- no other vehicles or lighting are de-
tected;
Automatic main beam
- the vehicle speed is above approxi-
headlights
mately 25 mph (40 km/h).
Depending on the vehicle, this system
If any of the above conditions are not
switches the main beam headlights on
fulfilled, the system switches to dipped
and off automatically. It uses a camera
beam headlights.
located behind the interior rear-view
Note: make sure the windscreen is not
mirror to detect vehicles that are being
3
obscured (dirt, mud, snow, condensa-
followed and those coming in the oppo-
tion etc.).
site direction.
Main beam headlights
á
With the engine running and
the dipped beam headlights lit, push
stalk 1. This indicator light on the instru-
ment panel comes on.
The system may encounter difficul-
To return to the dipped headlight posi-
ties under certain conditions, inclu-
tion, pull stalk 1 towards you again.
ding:
- extreme weather conditions (rain,
snow, fog, etc.);
- obstruction in front of the wind-
screen or camera;
- when a following or oncoming ve-
hicle has weak or hidden lighting;
- incorrect settings for the front
headlights;
- reflective systems;
- ...
1.103
EXTERIOR LIGHTING AND SIGNALS (3/6)
To deactivate automatic main beam
1
headlights:
2
- pull stalk 1;
- or turn ring 2 to a position other than
AUTO.
Warning light
goes out on the in-
strument panel.
Note: make sure the windscreen is not
obscured (dirt, mud, snow, condensa-
tion, etc.).
Operating faults
Using the portable naviga-
When the message “Check Automatic
tion system at night in the
Lighting” appears on the instrument
windscreen area below the
Automatic main beam
panel, the system is deactivated.
camera may disturb the op-
headlights (continued)
Consult an approved dealer.
eration of the “automatic main beam
headlights” system (risk of reflection
on the windscreen).
Activation/deactivation
To activate the automatic main beam
headlights:
- turn the ring 2 until the AUTO symbol
is opposite the mark 3;
The “automatic main beam
- push the stalk 1.
headlights” system should
under no circumstances be
used to replace driver atten-
Warning light
comes on the in-
tion and responsibility with regard
strument panel.
to vehicle lighting and adapting to
light, visibility and traffic conditions.
1.104

 

 

 

 

 

 

 

Content      ..     3      4      5      6     ..