Peugeot 2008 (2016 year). Instruction - part 21

 

  Index      Peugeot     Peugeot 2008 - instruction 2016 year in english

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  19  20  21  22   ..

 

 

Peugeot 2008 (2016 year). Instruction - part 21

 

 

319

.

Audio and Telematics

2008_en_Chap12b_SMEGplus_ed01-2016

QUESTION

ANSWER

SOLUTION

Certain traffic jams along 
the route are not indicated 
in real time.

On starting, it is several minutes before the system begins to receive 
the traffic information.

Wait until the traffic information is being received 
correctly (display of the traffic information icons 
on the map).

The filters are too restrictive.

Modify the settings.

In certain countries, only major routes (motorways...) are listed for 
the traffic information.

This phenomenon is normal. The system is 
dependent on the traffic information available.

The altitude is not 
displayed.

On starting, the initialisation of the GPS may take up to 3 minutes to 
receive more than 4 satellites correctly.

Wait until the system has started up completely so 
that there is GPS coverage by at least 4 satellites.

Depending on the geographical environment (tunnel...) or the 
weather, the conditions of reception of the GPS signal may vary.

This phenomenon is normal. The system 
is dependent on the GPS signal reception 
conditions.

320

Audio and Telematics

2008_en_Chap12b_SMEGplus_ed01-2016

Radio

QUESTION

ANSWER

SOLUTION

The quality of reception of 
the radio station listened 
to gradually deteriorates 
or the stored stations do 
not function (no sound, 
87.5 Mhz is displayed...).

The vehicle is too far from the transmitter used by the station 
listened to or there is no transmitter in the geographical area 
through which the vehicle is travelling.

Activate the "RDS" function by means of the 
short-cut menu to enable the system to check 
whether there is a more powerful transmitter in 
the geographical area.

The environment (hills, buildings, tunnels, basement car parks...) 
block reception, including in RDS mode.

This phenomenon is normal and does not indicate 
a fault with the audio system.

The aerial is absent or has been damaged (for example when going 
through a car wash or into an underground car park).

Have the aerial checked by a PEUGEOT dealer.

I cannot find some radio 
stations in the list of 
stations received.

The station is not received or its name has changed in the list.

Press and hold the "List" button at the steering 
mounted controls to update the list of stations 
received or press on the system update function: 
"Update list".

Some radio stations send other information in place of their name 
(the title of the song for example).
The system interprets this information as the name of the station.

The name of the radio 
station changes.

321

.

Audio and Telematics

2008_en_Chap12b_SMEGplus_ed01-2016

Media

QUESTION

ANSWER

SOLUTION

Playback of my USB 
memory stick starts only 
after a very long wait 
(around 2 to 3 minutes).

Some files supplied with the memory stick may greatly slow down 
access to reading the memory stick (multiplication by 10 of the 
catalogue time).

Delete the files supplied with the memory stick 
and limit the number of sub-folders in the file 
structure on the memory stick.

When I connect my iPhone 
as a telephone and to the 
USB port at the same time, 
I am unable to play the 
music files.

When the iPhone connects automatically as a telephone, it forces 
the streaming function. The streaming function takes the place of 
the USB function which is then not useable, there is a period without 
sound of the track being played with Apple

®

 players.

Disconnect and reconnect to the USB port (the 
USB function takes priority over streaming).

The CD is ejected 
automatically or is not 
played by the player.

The CD is inserted upside down, is unplayable, does not contain any 
audio data or contains an audio format which the player cannot play.

Check that the CD is inserted in the player the 
right way up.
Check the condition of the CD: the CD cannot be 
played if it is too badly damaged.
Check the content in the case of a recorded CD: 
refer to the advice in the "AUDIO" section.
The audio system's CD player does not play 
DVDs.
Some recorded CDs will not be played by the 
audio system because they are not of adequate 
quality.

The CD has been recorded in a format that is not compatible with the player (udf...).

The CD is protected by an anti-pirating protection system which is 
not recognised by the audio system.

There is a long waiting 
period following the insertion 
of a CD or connection of a 
USB memory stick.

When a new medium is inserted, the system reads a certain 
amount of data (directory, title, artist, etc.). This may take from a few 
seconds to a few minutes.

This phenomenon is normal.

322

Audio and Telematics

2008_en_Chap12b_SMEGplus_ed01-2016

QUESTION

ANSWER

SOLUTION

The CD player sound is 
poor.

The CD used is scratched or of poor quality.

Insert good quality CDs and store them in suitable 
conditions.

The audio equipment settings (bass, treble, ambiences) are 
unsuitable.

Set the treble or bass level to 0, without selecting 
an ambience.

Some characters in the 
media information are not 
displayed correctly while 
playing.

The audio system does not display some types of characters.

Use standard characters to name tracks and 
folders.

Playing of streaming files 
does not start.

The peripheral device connected does not support automatic play.

Start the playback from the device.

The names of tracks and 
the track length are not 
displayed on the screen 
when streaming audio.

The Bluetooth profile does not allow the transfer of this information.

323

.

Audio and Telematics

2008_en_Chap12b_SMEGplus_ed01-2016

QUESTION

ANSWER

SOLUTION

In changing the setting 
of treble and bass the 
equalizer setting is 
deselected.

The selection of an equalizer setting imposes the balance settings.
Modifying one without the other is not possible.

Modify the balance or equalizer settings to obtain 
the desired musical ambience.

In changing the equalizer 
setting, treble and bass 
return to zero.

When changing the 
balance settings, the 
distribution setting is 
deselected.

The selection of a distribution setting imposes the balance settings.
Modifying one without the other is not possible.

Modify the balance or distribution settings to 
obtain the desired musical ambience.

When changing an 
distribution setting, 
the balance setting is 
deselected.

Settings

324

Audio and Telematics

2008_en_Chap12b_SMEGplus_ed01-2016

QUESTION

ANSWER

SOLUTION

There is a difference in 
sound quality between the 
different audio sources.

For optimum sound quality, the audio settings for Loudness, 
Ambience, Treble, Bass, Volume can be adapted to the different 
sound sources, which may result in audible differences when 
changing source.

Check that the audio settings (Loudness, 
Ambience, Treble, Bass, Volume) are adapted to 
the sources listened to. Adjust Balance, Treble 
and Bass to the middle position, select the 
"None" musical ambience and set the loudness 
correction to the "Active" position in CD mode or 
to the "Inactive" position in radio mode.

With the engine off, the 
system switches off after a 
few minutes of use.

When the engine is switched off, the system's operating time 
depends on the state of charge of the battery.
The switch-off is normal: the system switches to economy mode and 
switches off to prevent discharging of the vehicle's battery.

Start the vehicle's engine to increase the battery 
charge.

325

.

Audio and Telematics

2008_en_Chap12b_SMEGplus_ed01-2016

QUESTION

ANSWER

SOLUTION

I cannot connect my 
Bluetooth telephone.

The telephone's Bluetooth function may be switched off or the 
telephone may not be visible.

Check that your telephone's Bluetooth function is 
switched on.
Check in the telephone settings that it is "visible 
to all".

The Bluetooth telephone is not compatible with the system.

You can check the compatibility of your 
telephone at www.peugeot.co.uk (services).

The volume of the 
telephone connected 
in Bluetooth mode is 
inaudible.

The volume depends both on the system and on the telephone.

Increase the volume of the audio system, to 
maximum if required, and increase the volume of 
the telephone if necessary.

The ambient noise level has an influence on the quality of 
telephone communication.

Reduce the ambient noise level (close the 
windows, reduce the booster fan speed, slow 
down...).

Some contacts are 
duplicated in the list.

The options for synchronizing contacts are synchronizing the 
contacts on the SIM card, the contacts on the telephone, or both. 
When both synchronizations are selected, some contacts may be 
duplicated.

Select "Display SIM card contacts" or "Display 
telephone contacts".

Contacts are not shown in 
alphabetical order.

Some telephones offer display options. Depending on the settings 
chosen, contacts can be transferred in a specific order.

Modify the display setting in the telephone 
directory.

The system does not 
receive SMS text messages.

The Bluetooth mode does not permit sending SMS text messages 
to the system.

Telephone

327

.

Audio and Telematics

2008_en_Chap12c_RDE2_ed01-2016

Audio system / Bluetooth

®

Contents

First steps 

328

Steering mounted controls 

329

Radio 330
Media 332
Telephone 336
Audio settings 

339

Configuration 

340

Screen menu map(s) 

341

Frequently asked questions 

342

As a safety measure, the driver must only carry out operations 
which require prolonged attention while the vehicle is stationary.
When the engine is switched off and to prevent discharging of 
the battery, the system switches off after activation of energy 
economy mode.

328

Audio and Telematics

2008_en_Chap12c_RDE2_ed01-2016

First steps

On / Off, volume adjustment.

Select the source:
Radio: FM1, FM2, AM, CD, USB, 
AUX, Streaming.
Telephone: accept an incoming call.
Telephone, press and hold: end 
a call, access the calls log for the 
connected telephone.

Display the list of stations received, 
the CD/USB tracks or folders.
Press and hold: update the list of 
stations received.

Automatic search for a lower radio 
frequency.
Select the previous CD, USB track.
Navigation in a list.
Press and hold: fast back.

Automatic search for a higher radio 
frequency.
Select the next CD, USB track.
Navigation in a list.
Press and hold: fast forward.

Adjust audio settings: sound 
ambience, treble, bass, loudness, 
distribution, left/right balance, front/
rear balance, automatic volume.

Abandon the current operation.
Go up one level (menu or folder).

Select a preset radio station.
Radio, press and hold: preset a radio 
station.
Other than radio: see the 
corresponding sections.

Eject CD.

Open the main menu.

329

.

Audio and Telematics

2008_en_Chap12c_RDE2_ed01-2016

Steering mounted controls

Radio: select the previous / next 
preset station.
CD / USB: select the genre / 
artist / folder / playlist from the list 
depending on classification.
Select the previous / next item  
in a menu.

Volume decrease.

Radio: automatic search for a higher 
frequency.
CD / MP3 / USB: select the next 
track.
CD / USB: press and hold: fast 
forward.

Mute: cut the sound by 
simultaneously pressing the volume 
increase and decrease buttons.
Restore the sound: by pressing one 
of the two volume buttons.

Radio: automatic search for a lower 
frequency.
CD / MP3 / USB: select the previous 
track.
CD / USB: press and hold: fast back.

Change the audio sound.
Confirm a selection.
Start/end call with the telephone.
Press and hold: access to the 
call log.

Volume increase.

330

Audio and Telematics

2008_en_Chap12c_RDE2_ed01-2016

Radio

Presetting a station

Selecting a station

Managing a list

Entering a frequency

Press SRC/TEL repeatedly to select 
the FM1, FM2 or AM waveband.

Press and hold one of the buttons to 
preset the station being listened to. 
The name of the station is displayed 
and an audible signal confirms the 
preset.

Press a button to listen to the 
corresponding preset station.

Select "Radio".

Select "Write freq.".

Press +.

or

press - to select the desired 
frequency.

Briefly press one of the buttons to 
change to the next or previous letter.

Press and hold on LIST to build or 
update the list of stations; audio 
reception is cut momentarily.

Press LIST to display the list of 
stations received in alphabetical 
order.

Select the desired radio station using 
one of the buttons.

Confirm with "OK".

Confirm with "OK".

The exterior environment (hills, buildings, 
tunnel, car park, below ground...) may 
prevent reception, even in RDS station 
tracking (alternative frequencies) mode. This 
phenomenon is normal in the propagation of 
radio waves and is in no way indicative of a 
fault with the audio system.

Press on MENU.

331

.

Audio and Telematics

2008_en_Chap12c_RDE2_ed01-2016

Select "Radio".

Select "Radio".

Select "Radio".

Select or deselect "RDS" to switch 
RDS on or off.

Select or deselect "TXT" to activate 
or deactivate the display of Radio 
Text.

Select or deselect "TA" to activate 
or deactivate the reception of traffic 
messages.

Confirm with "OK" to save the 
setting.

Confirm with "OK" to save the 
setting.

Confirm with "OK" to save the 
setting.

Receiving TA messages

RDS

Displaying RADIO TEXT

The TA (Traffic Announcement) 
function gives priority to TA alert 
messages. To operate, this function 
needs good reception of a radio station 
transmitting this type of message. 
When a traffic report is transmitted, 
the current audio source (Radio, CD, 
USB, ...) is interrupted automatically to 
play the TA message. Normal playback 
of the audio source resumes at the end 
of the transmission of the message.

RDS, if activated, enables you to continue 
listening to the same station by automatic 
retuning to alternative frequencies. 
However, in certain conditions, coverage 
of an RDS station may not be assured 
throughout the country as radio stations 
do not cover 100 % of the territory. This 
explains the loss of reception of the 
station during a journey.

Radio text is information transmitted by 
the radio station related to the current 
programme or song.

With source FM1 or FM2, 
press MENU.

With the radio displayed on the 
screen, press MENU.

Press MENU.

332

Audio and Telematics

2008_en_Chap12c_RDE2_ed01-2016

Media

USB player

This unit comprises a USB port 
and a Jack auxiliary socket, 
depending on model.

Connect a USB memory stick to the USB port 
or connect a USB device to the USB port using 
a suitable cable (not supplied).

The system constitutes playlists (in 
temporary memory) the creation time 
for which can be from a few seconds to 
several minutes at the first connection.
Limiting the number of non-music files 
and the number of folders reduces this 
waiting time. The playlists are updated 
every time the ignition is switched off or 
a USB memory stick is connected.
The lists are memorised: if there is no 
change in the lists, the next loading 
time will be shorter.

Press SRC/TEL repeatedly to 
select "USB".

Press one of these buttons to select 
the next or previous track in the list.

Press and hold one of these buttons 
for fast forward or back.

Press one of these buttons to select 
the next or previous folder in the 
order chosen.

Press LIST to display the structure of 
the folders in the compilation.

Select a line in the list.

Confirm with "OK".

Up a level in the menu.

Select "Media".

Select the play mode: "Normal"
"Random""Random all" or 
"Repeat".

Select or deselect "TA" to switch 
traffic announcements on or off.

Press MENU.

At a first connection, the order 
suggested is by folder. When 
connecting again, the order previously 
chosen is retained.

333

.

Audio and Telematics

2008_en_Chap12c_RDE2_ed01-2016

Press the SRC/TEL button 
repeatedly to select "CD".

Press one of these buttons to go to 
the previous or next track in the list.

Press and hold one of these buttons 
for fast forward or back.

Auxiliary socket (AUX)

Connect the portable device (MP3 player...) to 
the Jack auxiliary socket using an audio cable 
(not supplied).

Press SRC/TEL repeatedly to 
select "AUX".

First adjust the volume on the portable device 
(to a high level). Then adjust the volume on 
your audio system. Control is from the portable 
device.

Do not connect a given device to both 
the Jack auxiliary socket and the USB 
port at the same time.

CD player

Insert a CD into the player, play starts 
automatically.
Insert an MP3 compilation CD into the CD 
player.
The audio system searches for audio tracks, 
which can take from a few to several dozen 
seconds before play starts.

Press one of these buttons to select 
the previous or next folder according 
to the category chosen.

Press LIST to display the folder 
structure of the compilation.

Select a line in the list.

Confirm with "OK".

Return to the top level of the folder structure to 
select the type of tracks.
- By 

Folders (CD or USB): all folders 

containing audio files recognised on the 
peripheral device, in alphabetical order 
without following the folder structure.

- By 

Artist (USB only): all of the artist names 

defined in the ID3 Tags, in alphabetical 
order.

- By 

Genre (USB only): all of the genres 

defined in the ID3 Tags.

- By 

Playlist (CD or USB): if playlists have 

been saved.

334

Audio and Telematics

2008_en_Chap12c_RDE2_ed01-2016

The audio system will only play files with 
".mp3", ".wma" and ".wav" on a CD and can 
play files with ".ogg" extension only on USB.

It is recommended that file names be of no 
more than 20 characters and avoiding special 
characters (ex: " ? ; ù) so as to avoid any 
problem reading or displaying the files.

In order to be able to play a recorded CDR or 
CDRW, when recording it is preferable to select 
standards ISO 9660 level 1. 2 or Joliet.
If the disc is recorded in another format, it may 
not be played correctly.
It is recommended that the same recording 
standard is always used for an individual disc, 
with as low a speed as possible (4x maximum) 
for optimum sound quality.
In the particular case of a multi-session CD, the 
Joliet standard is recommended.

Information and advice

Use only USB memory sticks formatted FAT32 
(File Allocation Table).

The use of genuine Apple

®

 USB cables 

is recommended to ensure correct 
operation.

On a single disc, the CD player can read up 
to 255 MP3 files spread over 8 folder levels 
with a maximum of 192 folders. However, it is 
recommended that this be kept to 2 levels so 
as to limit the time taken to access and play 
the CD.
During play, the folder structure is not 
observed.

Do not connect a hard disk or USB device other 
than audio players to the USB port. This may 
cause damage to your installation.

The playlists accepted on CD, MP3, iPod and 
USB connection are types ".m3u" and ".wpl".
The number of files recognised is limited to 
5 000 in 500 folders on a maximum of 8 levels.

 

 

 

 

 

 

 

Content   ..  19  20  21  22   ..