Opel Frontera UBS. Manual - part 461

 

  Index      Opel     Opel Frontera UBS - service repair manual 1998-2002 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  459  460  461  462   ..

 

 

Opel Frontera UBS. Manual - part 461

 

 

MEMO

ENGINE ELECTRICAL 6D – 1

ENGINE ELECTRICAL

CONTENTS 

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

6D–1

General Description . . . . . . . . . . . . . . . . 

6D–1

Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . 

6D–1

On Vehicle Service . . . . . . . . . . . . . . . . . 

6D–3

Main Data and Specification . . . . . . . . . . 

6D–4

Starting System . . . . . . . . . . . . . . . . . . . . . 

6D–5

General Description . . . . . . . . . . . . . . . . 

6D–5

On Vehicle Service . . . . . . . . . . . . . . . . . 

6D–7

Starter . . . . . . . . . . . . . . . . . . . . . . . . . . 

6D–7

Unit Repair . . . . . . . . . . . . . . . . . . . . . . . 

6D–8

Charging System . . . . . . . . . . . . . . . . . . . . 

6D–15

General Description . . . . . . . . . . . . . . . . 

6D–15

Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . 

6D–16

Unit Repair . . . . . . . . . . . . . . . . . . . . . . . 

6D–17

Main Data and Specification . . . . . . . . . . 

6D–22

QOS4 Preheating System . . . . . . . . . . . . . . 

6D–23

General Description . . . . . . . . . . . . . . . . 

6D–23

System Diagram . . . . . . . . . . . . . . . . . . . 

6D–23

Inspection of QOS4 System Operation . . 

6D–24

BATTERY

GENERAL DESCRIPTION

DIAGNOSIS

There are six battery fluid caps at the top of the battery.
These are covered by a paper label.
The battery is completely sealed except for the six
small vent holes at the side. These vent holes permit
the escape of small amounts of gas generated by the
battery.
This type of battery has the following advantages over
conventional batteries:

1. There is no need to add water during the entire

service life of the battery.

2. The battery protects itself against overcharging.

The battery will refuse to accept an excessive
charge.
(A conventional battery will accept an excessive
charge, resulting in gassing and loss of battery
fluid.)

3. The battery is much less vulnerable to self-

discharge than a conventional type battery.

1. VISUAL INSPECTION (Step 1)

Inspect the battery for obvious physical damage, such
as a cracked or broken case, which would permit
electrolyte loss.
Replace the battery if obvious physical damage is
discovered during inspection.
Check for any other physical damage and correct it as
necessary. If not, proceed to Step 2.

2. HYDROMETER CHECK (Step 2)

There is a built-in hydrometer (Charge test indicator) at
the top of the battery. It is designed to be used during
diagnostic procedures.
Before trying to read the hydrometer, carefully clean the
upper battery surface.
If your work area is poorly lit, additional light may be
necessary to read the hydrometer.

a. BLUE RING OR DOT VISIBLE – Go to Step 4.
b. BLUE RING OR DOT NOT VISIBLE – Go to

Step 3.

3. FLUID LEVEL CHECK (Step 3)

The fluid level should be between the upper level line
and lower level line on side of the battery.

a. CORRECT FLUID LEVEL – Charge the battery.
b. BELOW LOWER LEVEL – Replace battery.

4. VOLTAGE CHECK (Step 4)

(1) Put voltmeter test leads to battery terminals.

a. VOLTAGE IS 12.4V OR ABOVE – Go to Step 5.
b. VOLTAGE IS UNDER 12.4V – Go to procedure

(2) below.

(2) Determine fast charge amperage from

specification. (See Main Data and Specifications in
this section.)
Fast charge battery for 30 minutes at amperage
rate no higher than specified value.
Take voltage and amperage readings after charge.
a. VOLTAGE IS ABOVE 16V AT BELOW 1/3 OF

AMPERAGE RATE – Replace battery.

SECTION

6D – 2 ENGINE ELECTRICAL

b. VOLTAGE IS ABOVE 16V AT ABOVE 1/3 OF

AMPERAGE RATE – Drop charging voltage to
15V and charge for 10 – 15 hours.
Then go to Step 5.

c. VOLTAGE IS BETWEEN 12V AND 16V –

Continue charging at the same rate for an
additional 3-1/2 hours. Then go to Step 5.

d. VOLTAGE IS BELOW 12V – Replace battery.

5. LOAD TEST (Step 5)

(1) Connect a voltmeter and a battery load tester

across the battery terminals.

(2) Apply 300 ampere load for 15 seconds to remove

surface charge from the battery.
Remove load.

(3) Wait 15 seconds to let battery recover. Then apply

specified load from specifications (See Main Data
and Specifications in this section).
Read voltage after 15 seconds, then remove load.
a. VOLTAGE DOES NOT DROP BELOW THE

MINIMUM LISTED IN FOLLOWING TABLE –
The battery is good and should be returned to
service.

b. VOLTAGE IS LESS THAN MINIMUM LISTED –

Replace battery.

ESTIMATED

TEMPERATURE

MINIMUM

°F

°C

VOLTAGE

70

21

9.6

60

16

9.5

50

10

9.4

40

4

9.3

30

–1

9.1

20

–7

8.9

10

–12

8.7

0

–18

8.5

The battery temperature must be estimated by feel
and by the temperature the battery has been
exposed to for the preceding few hours.

ENGINE ELECTRICAL 6D – 3

ON-VEHICLE SERVICE

BATTERY CHARGING

Observe the following safety precautions when
charging the battery:

1. Never attempt to charge the battery when the fluid

level is below the lower level line on the side of the
battery. In this case, the battery must be replaced.

2. Pay close attention to the battery during the

charging procedure.
Battery charging should be discontinued or the rate
of charge reduced if the battery feels hot to the
touch.
Battery charging should be discontinued or the rate
of charge reduced if the battery begins to gas or
spew electrolyte from the vent holes.

3. In order to more easily view the hydrometer blue

dot or ring, it may be necessary to jiggle or tilt the
battery.

4. Battery temperature can have a great effect on

battery charging capacity.

5. The sealed battery used on this vehicle may be

either quick-charged or slow-charged in the same
manner as other batteries.
Whichever method you decide to use, be sure that
you completely charge the battery. Never partially
charge the battery.

JUMP STARTING

JUMP STARTING WITH AN AUXILIARY
(BOOSTER) BATTERY

CAUTION: Never push or tow the vehicle in an
attempt to start it. Serious damage to the emission
system as well as other vehicle parts will result.

Treat both the discharged battery and the booster
battery with great care when using jumper cables.
Carefully follow the jump starting procedure, being
careful at all times to avoid sparking.

WARNING: Failure to carefully follow the jump
starting procedure could result in the following:

1. Serious personal injury, particularly to your

eyes.

2. Property damage from a battery explosion,

battery acid, or an electrical fire.

3. Damage to the electronic components of one or

both vehicles.

Never expose the battery to an open flame or electrical
spark. Gas generated by the battery may catch fire or
explode. Remove any rings, watches, or other jewelry
before working around the battery. Protect your eyes by
wearing an approved set of goggles.
Never allow battery fluid to come in contact with your
eyes or skin.
Never allow battery fluid to come in contact with fabrics
or painted surfaces.
Battery fluid is a highly corrosive acid.

Should battery fluid come in contact with your eyes,
skin, fabric, or a painted surface, immediately and
thoroughly rinse the affected area with clean tap water.
Never allow metal tools or jumper cables to come in
contact with the positive battery terminal, or any other
metal surface of the vehicle. This will protect against a
short circuit.
Always keep batteries out of the reach of young
children.

JUMP STARTING PROCEDURE

1. Set the vehicle parking brake.

If the vehicle is equipped with an automatic
transmission, place the selector lever in the “PARK”
position.
If the vehicle is equipped with a manual
transmission place the shift lever in the “NEUTRAL”
position.
Turn “OFF” the ignition.
Turn “OFF”  all lights and any other accessory
requiring electrical power.

2. Look at the built-in hydrometer.

If the indication area of the built-in hydrometer is
completely clear, do not try to jump start.

3. Attach the end of one jumper cable to the positive

terminal of the booster battery.
Attach the other end of the same cable to the
positive terminal of the discharged battery.
Do not allow the vehicles to touch each other.
This will cause a ground connection, effectively
neutralizing the charging procedure.
Be sure that the booster battery has a 12 volt rating.

4. Attach one end of the remaining cable to the

negative terminal of the booster battery.
Attach the other end of the same cable to a solid
engine ground (such as the A/C compressor
bracket or the generator mounting bracket) of the
vehicle with the discharged battery.
This ground connection must be at least 450 mm
(18 in) from the battery of the vehicle whose battery
is being charged.

WARNING: Never attach the end of the jumper
cable directly to the negative terminal of the dead
battery.

5. Start the engine of the vehicle with the good battery.

Make sure that all unnecessary electrical
accessories have been turned “OFF”.

6. Start the engine of the vehicle with the dead battery.
7. To remove the jumper cables, follow the above

directions in the reverse order.
Be sure to first disconnect the negative cable from
the vehicle with the discharged battery.

 

 

 

 

 

 

 

Content   ..  459  460  461  462   ..