Opel Frontera UBS. Manual - part 1682

 

  Index      Opel     Opel Frontera UBS - service repair manual 1998-2002 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1680  1681  1682  1683   ..

 

 

Opel Frontera UBS. Manual - part 1682

 

 

8D–406

WIRING SYSTEM

STEP

OPERATION

ITEM TO BE CHECKED

ITEM OF

REMARKS

MALFUNCTION

Activate alarm
device.

Check to see if indicator light
goes off after about 10 seconds.

Check to see if alarm operates.

Check to see if alarm stops.

Wait about 10 seconds.

Open engine hood with engine
hood release handle.

Insert key into starter switch and
turn it to “ACC” position.

C

I

J

45

46

47

NOTE: When the connector of the anti–theft & keyless entry control unit is disconnected, the starter is inoperative.

In the checking of short wheel base model, Step Nos. 16 through 21 and Step Nos. 31 through 36 are omitted.

WIRING SYSTEM

8D–407

TERMINAL

CONNECTION

CHECK

OPERATION

CIRCUIT

NO.

ITEM

CONDITION

1

FRT door switch–LH, RH

Continuity

Open door

Continuity

Close door

No continuity

2

RR door switch–LH, RH

Continuity

Open door

Continuity

Close door

No continuity

3

4

Door lock key switch–LH, RH

Continuity

Lock with key

Continuity

5

FRT door lock switch–LH, RH

Continuity

Lock

Continuity

6

Tailgate switch

Continuity

Open tailgate

Continuity

Close tailgate

No continuity

8

Anti–theft horn

Voltage

Approx. 12V

10

Battery

Voltage

Approx. 12V

11

Door switch

Continuity

Unlock with locking knob

Continuity

Lock with locking knob

No continuity

12

Engine hood switch

Continuity

Open engine hood

Continuity

Close engine hood

No continuity

13

Detect switch

Continuity

Unlock with key

Continuity

Lock with key

No continuity

14

Door lock key switch

Continuity

Unlock

Continuity

15

FRT door lock switch–LH, RH

Continuity

Unlock

Continuity

16

Tamper switch

Continuity

No continuity

17

Ground

Continuity

Continuity

18

Starter switch

Voltage

Starter switch “ACC”

Approx. 12V

19

Indicator light

Voltage

Approx. 12V

20

Dome light

Voltage

Dome light “DOOR” position

Approx. 12V

21

Anti-theft relay

Voltage

Approx. 12V

22

Starter relay

Voltage

Mode switch “P” or “N”

Approx. 12V

Clutch pedal depressed

Approx. 12V

Connector Check Table

Check the anti–theft & keyless entry control unit harness side connector B–20 by using a circuit tester.

8D–408

WIRING SYSTEM

ID Code Registration

There are four kinds of ID codes which can be registered,
for which these three modes, ID code new registration, ID
code additional registration and ID code check, are
available.

ID Code New Registration

This procedure erases all registered ID codes and
registers a new received ID code instead.

Step

Action

Yes

No

1. Open the driver’s side door.
2. Turn the starter switch off.

Is the action complete?

Turn the starter switch to ACC position and then off three times
within five seconds after step 1.

Is the action complete within five seconds?

Close the door and then open it two times within ten seconds after
step 2.

Is the action complete within ten seconds?

1. Turn the starter switch to ACC position and then off five times.
2. Close the door and then open it.

NOTE: This step must be performed within ten seconds after step
3.

Is the action complete?

The control unit makes lock/unlock response once with interval of
one second.

Is the response complete?

Operate the lock or unlock button of transmitter within twenty
seconds after step 5.

Is the action complete?

The control unit makes lock/unlock response once with interval of
one second as ID temporary registration.

Is the response complete?

Operate the lock or unlock button of transmitter within twenty
seconds after step 7.

Is the action complete?

The control unit compares temporary registered ID code with
receiving ID code.

Is temporary registered ID code the same as receiving ID code?

The control unit makes lock/unlock response three times with
interval of one second.

Is the response complete?

The control unit erases all registered ID codes and registers new
ID code.

Is the registration complete?

1

2

3

4

5

6

7

8

9

10

11

Go to Step 2

Go to Step 3

Go to Step 4

Go to Step 5

Go to Step 6

Go to Step 7

Go to Step 8

Go to Step 9

Go to Step 11

Finished

Go to Step 12

Finished

Finished

Finished

Finished

Finished

Go to Step 11

Go to Step 13

WIRING SYSTEM

8D–409

Step

Action

Yes

No

The control unit makes lock/unlock response once with interval of
one second.

Is the response complete?

The control unit makes lock/unlock response three times with
interval of one second.

Is the response complete?

12

13

Finished

Finished

Step

Action

Yes

No

1. Open the driver’s side door.
2. Turn the starter switch off.

Is the action complete?

Turn the starter switch to ACC position and then off three times
within five seconds after step 1.

Is the action complete within five seconds?

Close the door and then open it two times within ten seconds after
step 2.

Is the action complete within ten seconds?

1. Turn the starter switch to ACC position and then off three

times.

2. Close the door and then open it.

NOTE: This step must be performed within ten seconds after step
3.

Is the action complete?

The control unit makes lock/unlock response two times with
interval of one second.

Is the response complete?

Operate the lock or unlock button of transmitter within twenty
seconds after step 5.

Is the action complete?

The control unit makes lock/unlock response two times with
interval of one second as ID temporary registration.

Is the response complete?

Operate the lock or unlock transmitter within twenty seconds after
step 7.

Is the action complete?

The control unit compares temporary registered ID code with
receiving ID code.

Is temporary registered ID code the same as receiving ID code?

The control unit makes lock/unlock response three times with
interval of one second.

Is the response complete?

The control unit registers new ID code.

Is the registration complete?

1

2

3

4

5

6

7

8

9

10

11

Go to Step 2

Go to Step 3

Go to Step 4

Go to Step 5

Go to Step 6

Go to Step 7

Go to Step 8

Go to Step 9

Go to Step 11

Finished

Go to Step 12

Finished

Finished

Finished

Finished

Finished

Go to Step 10

Go to Step 13

ID Code Additional Registration

This procedure additionally registers a new received ID
code with holding registered ID codes. When total
number of registered ID codes and newly registered ID
code exceeds four, they are erased in order of older one.

 

 

 

 

 

 

 

Content   ..  1680  1681  1682  1683   ..