Nissan Qashqai (2022 year). Manual in english

may damage the lens cover.

AIR FRESHENERS

Most air fresheners use a solvent that

could affect the vehicle interior. If you use

an air freshener, take the following pre-

cautions:

Hanging-type air fresheners can

cause permanent discoloration when

they contact vehicle interior surfaces.

Place the air freshener in a location

that allows it to hang free and not

contact an interior surface.

Liquid-type air fresheners typically clip

on the vents. These products can

cause immediate damage and disco-

loration when spilled on interior sur-

faces.

Carefully read and follow the manufac-

turer’s instructions before using air fresh-

eners.

FLOOR MATS

WARNING

To avoid potential pedal interference

that may result in a collision, injury

or death:

NEVER place a floor mat on top of

another floor mat in the driver

front position or install them up-

side down or backwards.

It is recommended that you use

only genuine NISSAN floor mats

specifically designed for use in

your vehicle model and model

year.

Properly position the mats in the

floorwell using the floor mat po-

sitioning hooks. See “Floor mat

installation” (P.7-5).

Make sure the floor mat does not

interfere with pedal operation.

Periodically check the floor mats

to make sure they are properly

installed.

After cleaning the vehicle interior,

check the floor mats to make

sure they are properly installed.

The use of genuine NISSAN floor mats can

extend the life of your vehicle carpet and

make it easier to clean the interior. Mats

should be maintained with regular clean-

ing and replaced if they become exces-

sively worn.

JVA0018X

Floor mat installation

Your vehicle is equipped with floor mat

positioning hook(s). The number and

shape of the floor mat positioning hook

(s) for each seating position varies de-

pending on the vehicle.
When installing genuine NISSAN floor

mats, follow the installation instructions

provided with the floor mat and the

following:
1. Position the floor mat in the floorwell

so that the floor mat grommet holes

are aligned with the hook(s).

2. Secure the grommet holes into the

hook(s) and ensure that the floor mat

Appearance and care

7-5

-------------------------------------------------------------------------------------------------------------------------------------------------------------

7-6

Appearance and care

is properly positioned.

3. Make sure the floor mat does not

interfere with pedal operation. With

the ignition in the OFF position and

the shift lever in the P (Park) position

(Continuously Variable Transmission

(CVT) models) or the shift lever in the

N (Neutral) position (Manual Transmis-

sion (MT) models), fully apply and

release all pedals. The floor mat must

not interfere with pedal operation or

prevent the pedal from returning to its

normal position. It is recommended

you see a NISSAN dealer for details

about installing the floor mats in your

vehicle.

JVA0031X

Positioning hook(s)

The illustration shows the location of the

floor mat positioning hook(s).

SEAT BELTS

The seat belts can be cleaned by wiping

them with a sponge dampened in a mild

soap solution. Allow the belts to dry

completely in the shade before using

them.
See “Seat belts” (P.1-12).

WARNING

Do not allow wet seat belts to roll up

in the retractor. NEVER use bleach,

dye, or chemical solvents to clean

the seat belts, since these materials

may severely weaken the seat belt

webbing.

CLEANING THE SEAT TRACKS

CAUTION

Periodically clean the seat tracks to

prevent reduction of ability to move

the seats.

Clean periodically with a high-powered

vacuum cleaner. Dirt and debris may

reduce the ability to adjust the seat. A

wet cleansing agent may be used if

necessary.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

MOST COMMON FACTORS CON-

TRIBUTING TO VEHICLE CORRO-

SION

The accumulation of moisture-retain-

ing dirt and debris in body panel

sections, cavities, and other areas.

Damage to paint and other protective

coatings caused by gravel and stone

chips or minor traffic accidents.

ENVIRONMENTAL FACTORS INFLU-

ENCE THE RATE OF CORROSION
Moisture

Accumulation of sand, dirt and water on

the vehicle body underside can acceler-

ate corrosion. Wet floor coverings will not

dry completely inside the vehicle, and

should be removed for drying to avoid

floor panel corrosion.

Relative humidity

Corrosion will be accelerated in areas of

high relative humidity, especially those

areas where the temperatures stay above

freezing where atmospheric pollution ex-

ists, or where road salt is used.

Temperature

A temperature increase will accelerate

the rate of corrosion to those parts which

are not well ventilated.

Air pollution

Industrial pollution, the presence of salt in

the air in coastal areas, or heavy road salt

use will accelerate the corrosion process.

Road salt will also accelerate the disin-

tegration of paint surfaces.

TO PROTECT YOUR VEHICLE FROM

CORROSION

Wash and wax your vehicle often to

keep the vehicle clean.

Always check for minor damage to the

paint and repair it as soon as possible.

Keep drain holes at the bottom of the

doors open to avoid water accumula-

tion.

Check the underbody for accumula-

tion of sand, dirt or salt. If present,

wash with water as soon as possible.

CAUTION

NEVER remove dirt, sand or other

debris from the passenger com-

partment by washing it out with a

hose. Remove dirt with a vacuum

cleaner.

Never allow water or other liquids

to come in contact with electronic

components inside the vehicle as

this may damage them.

Chemicals used for road surface deicing

are extremely corrosive. They accelerate

corrosion and deterioration of underbody

components such as the exhaust system,

fuel and brake lines, brake cables, floor

pan and fenders.

In winter, the underbody must be

cleaned periodically.

For additional protection against rust and

corrosion, which may be required in some

areas, it is recommended you consult a

NISSAN dealer.

Appearance and care

7-7

CORROSION PROTECTION

-------------------------------------------------------------------------------------------------------------------------------------------------------------

8-2

Do-it-yourself

When performing any inspection or main-

tenance work on your vehicle, always

take care to prevent serious accidental

injury to yourself or damage to the

vehicle. The following are general precau-

tions which should be closely observed.

WARNING

Park the vehicle on a level sur-

face, apply the parking brake

securely and block the wheels to

prevent the vehicle from moving.

Move the shift lever to the P

(Park) position (CVT model) or

the shift lever to the N (Neutral)

position (MT model).

Be sure the ignition switch is in

the OFF or LOCK position when

performing any parts replace-

ment or repairs.

If you must work with the engine

running, keep your hands, cloth-

ing, hair and tools away from

moving fans, belts and any other

moving parts.

It is advisable to secure or re-

move any loose clothing and

remove any jewelry, such as

rings, watches, etc. before work-

ing on your vehicle.

Always wear eye protection

whenever you work on your ve-

hicle.

If you must run the engine in an

enclosed space such as a garage,

be sure there is proper ventilation

for exhaust gases to escape.

Never get under the vehicle while

it is supported only by a jack. If it

is necessary to work under the

vehicle, support it with safety

stands.

Because the fuel lines are under

high pressure even when the

engine is off, it is recommended

you visit a NISSAN dealer for

service of the fuel filter or fuel

lines.

Do not work under the hood while

the engine is hot. Always turn off

the engine and wait until it cools

down.

If you must work with the engine

running, keep your hands, cloth-

ing, hair and tools away from

moving fans, belts and any other

moving parts.

Keep smoking materials, flame

and sparks away from fuel and

the battery.

On gasoline engine models with

the Multiport Fuel Injection (MFI)

system, the fuel filter and fuel

lines should be serviced because

the fuel lines are under high

pressure even when the engine

is turned off. It is recommended

that you visit a NISSAN dealer for

this service.

Your vehicle is equipped with an

automatic engine cooling fan. It

may come on at any time without

warning, even if the ignition

switch is in the OFF position and

the engine is not running. To

avoid injury, always disconnect

the negative battery cable before

working near the fan.

Avoid direct contact with used

engine oil and coolant. Impro-

perly disposed engine oil, engine

coolant, and/or other vehicle

fluids can hurt the environment.

Always conform to local regula-

tions for disposal of vehicle fluids.

CAUTION

Do not work under the hood while

the engine is hot. Turn the engine

MAINTENANCE PRECAUTIONS

-------------------------------------------------------------------------------------------------------------------------------------------------------------

off and wait until it cools down.

Avoid direct contact with used

engine oil and coolant. Impro-

perly disposed engine oil, and

engine coolant and/or other ve-

hicle fluids can damage the en-

vironment. Always conform to

local regulations for disposal of

vehicle fluid.

Never leave the engine or the CVT

related component harnesses

disconnected while the ignition

switch is in the ON position.

Never connect or disconnect the

battery or any transistorized

component while the ignition

switch is in the ON position.

Your vehicle is equipped with an

automatic engine cooling fan. It

may come on at any time without

warning, even if the ignition key is

in the OFF position and the en-

gine is not running. To avoid

injury, always disconnect the ne-

gative battery cable before work-

ing near the fan.

This “8. Do-it-yourself” section gives in-

structions regarding only those items

which are relatively easy for an owner to

perform.

A genuine NISSAN Service Manual is also

available. (See “Owner’s manual/service

manual order information” (P.10-21).)
You should be aware that incomplete or

improper servicing may result in operat-

ing difficulties or excessive emissions, and

could affect your warranty coverage.

If in

doubt about any servicing, it is recom-

mended you have it done by a NISSAN

dealer.

WAA0212X

Remove the air duct if necessary.
To remove the air duct

1. Remove the clips

with a suitable

tool.

2. Loosen the bolt

with a suitable tool.

3. Pull the air duct upward and then

sideways.

To install the air duct, perform the in-

stallation procedure in reverse order.

Do-it-yourself

8-3

ENGINE COMPARTMENT CHECK LOCATIONS

-------------------------------------------------------------------------------------------------------------------------------------------------------------

8-4

Do-it-yourself

WAA0211X

MR20DD ENGINE MODEL

Engine coolant reservoir

Engine oil filler cap

Brake and clutch* fluid reservoir

Air cleaner

Window washer fluid reservoir

Drive belt

Engine oil dipstick

Battery

Fuse/fusible link box

For Manual Transmission (MT) Model

The engine cooling system is filled at the

factory with a pre-diluted mixture of 50%

Genuine NISSAN Long Life Antifreeze/

Coolant (blue) and 50% water to provide

year-round anti-freeze and coolant pro-

tection. The anti-freeze solution contains

rust and corrosion inhibitors. Additional

engine cooling system additives are not

necessary.

WARNING

Never remove the radiator or

coolant reservoir cap when the

engine is hot. Wait until the en-

gine and radiator cool down.

Serious burns could be caused

by high pressure fluid escaping

from the radiator. See precau-

tions in “If your vehicle overheats”

(P.6-16) of this manual.

The radiator is equipped with a

pressure type radiator cap. To

prevent engine damage, use only

a genuine NISSAN radiator cap.

If the engine was stopped soon

when the engine is hot, the cool-

ing fan may operate for approxi-

mately 10 minutes after the

engine was stopped to cool the

components in the engine com-

ENGINE COOLING SYSTEM

-------------------------------------------------------------------------------------------------------------------------------------------------------------

partment. When the cooling fan is

operating, be sure that hands or

other items do not get caught in

it.

CAUTION

Never use any cooling system

additives such as radiator sealer.

Additives may clog the cooling

system and cause damage to

the engine, transmission and/or

cooling system.

When adding or replacing cool-

ant, be sure to use only Genuine

NISSAN Long Life Antifreeze/

Coolant (blue) or equivalent. Gen-

uine NISSAN Long Life Antifreeze/

Coolant (blue) is pre-diluted to

provide antifreeze protection to

-34°F(-37°C). If additional freeze

protection is needed due to

weather where you operate your

vehicle, add Genuine NISSAN Long

Life Antifreeze/Coolant (blue)

concentrate following the direc-

tions on the container. If an

equivalent coolant other than

Genuine NISSAN Long Life Anti-

freeze/Coolant (blue) is used, fol-

low the coolant manufacture’s

instructions to maintain mini-

mum antifreeze protection to

-34°F (-37°C). The use of other

types of coolant solutions other

than Genuine NISSAN Long Life

Antifreeze/Coolant (blue) or

equivalent may damage the en-

gine cooling system.

The life expectancy of the fac-

tory-fill coolant is 105,000 miles

(168,000 km) or 7 years. Mixing

any other type of coolant other

than Genuine NISSAN Long Life

Antifreeze/Coolant (blue) (or

equivalent coolant), including

Genuine NISSAN Long Life Anti-

freeze/Coolant (green), or the use

of non-distilled water will reduce

the life expectancy of the factory-

fill coolant. Refer to the “9. Main-

tenance and schedules” section

of this manual for more details.

JVM0438X

CHECKING ENGINE COOLANT LEVEL

Check the coolant level

in the reservoir

when the engine is cold.

If the coolant

level is below the MIN level

, open the

reservoir cap and add coolant up to the

MAX level

. If the reservoir is empty,

check the coolant level in the radiator

when the engine is cold.

If there is

insufficient coolant in the radiator, fill the

radiator with coolant up to the filler

opening and also add it to the reservoir

up to the MAX level

Tighten the cap securely after adding

engine coolant.

If the cooling system frequently re-

quires coolant, have it checked. It is

Do-it-yourself

8-5

-------------------------------------------------------------------------------------------------------------------------------------------------------------

8-6

Do-it-yourself

recommended you visit a NISSAN dealer

for this service.

CHANGING ENGINE COOLANT

A NISSAN dealer can change the engine

coolant. The service procedure can be

found in the NISSAN Service Manual.

Improper servicing can result in re-

duced heater performance and engine

overheating.

WARNING

To avoid being scalded, never

change the coolant when the

engine is hot.

Never remove the radiator or

coolant reservoir cap when the

engine is hot. Serious burns could

be caused by high pressure fluid

escaping from the radiator.

Avoid direct skin contact with

used coolant. If skin contact is

made, wash thoroughly with soap

or hand cleaner as soon as pos-

sible.

Keep coolant out of the reach of

children and pets.

Engine coolant must be disposed of

properly. Check your local regulations.

SDI1993

CHECKING ENGINE OIL LEVEL

1. Park the vehicle on a level surface and

apply the parking brake.

2. Run the engine until it reaches oper-

ating temperature.

3. Turn off the engine.

Wait more than

10 minutes for the oil to drain back

into the oil pan.

4. Remove the dipstick and wipe it clean.

Reinsert it all the way.

5. Remove the dipstick again and check

the oil level. It should be within the

range

. If the oil level is below

remove the oil filler cap and pour

recommended oil through the open-

ing.

Do not overfill

6. Recheck oil level with the dipstick.

It is normal to add some oil between oil

maintenance intervals or during the

break-in period, depending on the se-

verity of operating conditions.

CAUTION

Oil level should be checked regularly.

Operating the engine with an insuffi-

cient amount of oil can damage the

engine, and such damage is not

covered by the warranty.

CHANGING ENGINE OIL AND FILTER

WARNING

Used oil must be disposed of

properly. Never pour or dump oil

into the ground, canals, rivers,

etc. It should be disposed of at

proper waste facilities. NISSAN

recommends having your oil

changed by a NISSAN dealer.

Be careful not to burn yourself, as

the engine oil may be hot.

ENGINE OIL

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Prolonged and repeated contact

with used engine oil may cause

skin cancer.

Avoid direct skin contact with

used oil. If contacted, wash thor-

oughly with soap or hand cleaner

and plenty of water as soon as

possible.

Store used engine oil in marked

containers out of the reach of

children.

Vehicle set-up

1. Park the vehicle on a level surface and

apply the parking brake.

2. Run the engine until it reaches the

operating temperature.

3. Turn the engine off and wait more

than 10 minutes.

4. Raise and support the vehicle using a

suitable floor jack and safety jack

stands.

Place the safety jack stands under

the vehicle jack-up points.

A suitable adapter should be at-

tached to the jack stand saddle.

CAUTION

Make sure the correct lifting and

support points are used to avoid

vehicle damage.

JVM0414X

Do-it-yourself

8-7

-------------------------------------------------------------------------------------------------------------------------------------------------------------

8-8

Do-it-yourself

JVM0421X

Oil filler cap

Oil drain plug

Oil filter

Engine oil and filter

1. Place a large drain pan under the

drain plug.

2. Remove the oil filler cap.
3. Remove the drain plug with a wrench

and completely drain the oil.

CAUTION

Be careful not to burn yourself, as

the engine oil is hot.

Waste oil must be disposed of

properly.

Check your local regulations.

(Perform steps 4 to 7 only when the

engine oil filter change is needed.)

4. Loosen the oil filter with an oil filter

wrench. Remove the oil filter by turn-

ing it by hand.

5. Wipe the engine oil filter mounting

surface with a clean rag.

CAUTION

Be sure to remove any old gasket

material remaining on the mounting

surface of the engine. Failure to do

so could lead to engine damage.

6. Coat the gasket on the new filter with

clean engine oil.

7. Screw in the oil filter clockwise until a

slight resistance is felt, then tighten

additionally more than 2/3 turn.

Oil filter tightening torque:

11 to 15 ft-lb

(14.7 to 20.5 N·m)

8. Clean and re-install the drain plug

with a new washer. Securely tighten

the drain plug with a wrench.

Drain plug tightening torque:

22 to 29 ft-lb

(29 to 39 N·m)

Do not use excessive force.

9. Refill the engine with the recom-

mended oil through the oil filler open-

ing, and install the oil filler cap

securely.
See “Capacities and recommended

fluids/lubricants” (P.10-2) for drain

and refill capacity. The drain and refill

capacity depends on the oil tempera-

ture and drain time. Use these speci-

fications for reference only. Always

use the dipstick to determine the

proper amount of oil in the engine.

10. Start the engine and check for leak-

age around the drain plug and the oil

filter. Correct as required.

11. Turn the engine off and wait more

than 10 minutes. Check the oil level

with the dipstick. Add engine oil if

necessary.

After the operation

1. Lower the vehicle carefully to the

ground.

2. Dispose of waste oil and filter properly.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

WARNING

Prolonged and repeated contact

with used engine oil may cause

skin cancer.

Try to avoid direct skin contact

with used oil. If skin contact is

made, wash thoroughly with soap

or hand cleaner as soon as pos-

sible.

Keep used engine oil out of reach

of children.

When checking or replacement is re-

quired, we recommend a NISSAN dealer

for servicing.

CAUTION

NISSAN recommends using Gen-

uine NISSAN CVT Fluid NS-3 (or

equivalent) ONLY in NISSAN CVTs.

Do not mix with other fluids.

Do not use Automatic transmis-

sion fluid (ATF) or Manual Trans-

mission fluid in a NISSAN CVT, as

it may damage the CVT. Damage

caused by the use of fluids other

than as recommended is not

covered by the NISSAN’s New

Vehicle Limited Warranty.

Using fluids that are not equiva-

lent to Genuine NISSAN CVT Fluid

NS-3 may also damage the CVT.

Damage caused by the use of

fluids other than as recom-

mended is not covered by the

NISSAN’s New Vehicle Limited

Warranty.

For additional brake and clutch fluid

information, see “Capacities and recom-

mended fluids/lubricants” (P.10-2) of this

manual.

WARNING

Use only new fluid from a sealed

container. Old, inferior or con-

taminated fluid may damage the

brake and clutch systems. The

use of improper fluids can da-

mage the brake and clutch sys-

tems, and affect the vehicle’s

stopping ability.

Clean the filler cap before remov-

ing.

Brake and clutch fluid is poiso-

nous and should be stored care-

fully in marked containers out of

the reach of children.

CAUTION

Do not spill the fluid on any painted

surfaces. This will damage the paint.

If fluid is spilled, immediately wash

the surface with water.

Do-it-yourself

8-9

CONTINUOUSLY VARIABLE

TRANSMISSION (CVT) FLUID

BRAKE AND CLUTCH (if so equipped) FLUID

-------------------------------------------------------------------------------------------------------------------------------------------------------------

8-10

Do-it-yourself

JVM0789X

Check the fluid level in the reservoir. If the

fluid is below the MIN line

or the brake

warning light comes on, add Genuine

NISSAN Super Heavy Duty Brake Fluid or

equivalent

DOT 3

fluid up to the MAX line

. If fluid must be added frequently, the

system should be checked. It is recom-

mended you visit a NISSAN dealer for this

service.

JVM0788X

Type A

JVM0380X

Type B

Type A: Check the fluid level in the

window washer reservoir. If the fluid level

is low, add window washer fluid.
Type B: To check the fluid level, use your

finger to plug the center hole

of the

cap/tube assembly, then remove it from

the reservoir. If there is no fluid in the

tube, add fluid.
Add a washer solvent to the washer for

better cleaning. In the winter season, add

a windshield washer antifreeze. Follow

the manufacturer’s instructions for the

mixture ratio.
Fill the window washer fluid reservoir

periodically.
Add fluid when the low washer fluid

warning appears (if so equipped).
Refill the reservoir more frequently when

driving conditions require an increased

amount of window washer fluid.
Recommended fluid:
Genuine NISSAN Windshield Washer Con-

centrate Cleaner & Antifreeze or equiva-

lent

CAUTION

Do not substitute engine anti-

freeze coolant for window

washer solution. This may result

WINDOW WASHER FLUID

-------------------------------------------------------------------------------------------------------------------------------------------------------------

in damage to the paint.

Do not fill the window washer

reservoir tank with washer fluid

concentrates at full strength.

Some methyl alcohol based

washer fluid concentrates may

permanently stain the grille if

spilled while filling the window

washer reservoir tank.

Pre-mix washer fluid concen-

trates with water to the manu-

facturer’s recommended levels

before pouring the fluid into the

window washer reservoir tank. Do

not use the window washer re-

servoir tank to mix the washer

fluid concentrate and water.

Keep the battery surface clean and

dry. Clean the battery with a solution

of baking soda and water.

Make certain the terminal connec-

tions are clean and securely tightened.

If the vehicle is not to be used for 30

days or longer, disconnect the nega-

tive

battery terminal cable to pre-

vent discharging it.

NOTE:
Care should be taken to avoid situations

that can lead to potential battery dis-

charge and potential no-start condi-

tions such as:

Installation or extended use of elec-

tronic accessories that consume

battery power when the engine is

not running (Phone chargers, GPS,

DVD players, etc.)

Vehicle is not driven regularly and/

or only driven short distances.

In these cases, the battery may need to

be charged to maintain battery health.

WARNING

Do not expose the battery to

flames or electrical sparks. Hy-

drogen gas generated by the

battery is explosive. Do not allow

battery fluid to contact your skin,

eyes, fabrics or painted surfaces.

After touching a battery or bat-

tery cap, do not touch or rub your

eyes. Thoroughly wash your

hands. If the acid contacts your

eyes, skin or clothing, immedi-

ately flush with water for at least

15 minutes and seek medical

attention.

Do not operate the vehicle if the

fluid in the battery is low. Low

battery fluid can cause a higher

load on the battery which can

generate heat, reduce battery life,

and in some cases lead to an

explosion.

When working on or near a bat-

tery, always wear suitable eye

protection and remove all jew-

elry.

Battery posts, terminals and re-

lated accessories contain lead

and lead compounds. Wash

hands after handling.

Keep the battery out of the reach

of children.

Do-it-yourself

8-11

BATTERY

-------------------------------------------------------------------------------------------------------------------------------------------------------------

8-12

Do-it-yourself

DI0137MA

Check the fluid level in each cell. It should

be between the UPPER LEVEL

and

LOWER LEVEL

lines.

If it is necessary to add fluid, add only

distilled water to bring the level to the

indicator in each filler opening.

Do not

overfill.

SDI1480C

1. Remove the cell plugs

2. Add distilled water up to the UPPER

LEVEL

line.

If the side of the battery is not clear,

check the distilled water level by

looking directly above the cell; the

condition

indicates OK and the

condition

needs more to be added.

3. Tighten cell plugs

Vehicles operated in high temperatures

or under severe conditions require fre-

quent checks of the battery fluid level.

JUMP STARTING

If jump starting is necessary, see “Jump

starting” (P.6-14). If the engine does not

start by jump starting, the battery may

have to be replaced. It is recommended

you visit a NISSAN dealer for this service.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Nissan Qashqai (2022 year). Manual in english - page 26