Content .. 12 13 14 15 ..

Nissan Rogue Sport (2022 year). Manual in english - page 14

Front and rear view:

Guiding lines that indicate the approx-

imate vehicle width and distances to

objects with reference to the vehicle body

line

, are displayed on the monitor.

Distance guide lines:

Indicate distances from the vehicle body.

Red line

: approximately 1.5 ft (0.5 m)

Yellow line

: approximately 3 ft (1 m)

Green line

: approximately 7 ft (2 m)

Green line

(if so equipped): approxi-

mately 10 ft (3 m)

Vehicle width guide lines

Indicate the vehicle width.

Predictive course lines

Indicate the predictive course when op-

erating the vehicle. When the monitor

displays the rear view, the predictive

course lines will be displayed on the

monitor if the steering wheel is turned.

The predictive course lines will move

depending on how much the steering

wheel is turned and will not be displayed

while the steering wheel is in the straight

ahead position.
The front view will not be displayed when

the vehicle speed is above 6 MPH (10

km/h).

NOTE:

When the monitor displays the front

view and the steering wheel turns

about 90 degrees or less from the

straight ahead position, both the

right and left predictive course lines

are displayed. When the steering

wheel turns about 90 degrees or

more, the predictive course line is

displayed only on the opposite side

of the turn.

JVH1037X

Bird’s-eye view:

The bird’s-eye view shows the overhead

view of the vehicle which helps confirm

the vehicle position and the predictive

course to a parking space.
The vehicle icon

shows the position of

the vehicle. Note that the distance be-

tween objects viewed in the bird’s-eye

view differs from the actual distance.
The areas that the cameras cannot cover

are indicated in black.

After the ignition switch is placed in the

ON position, the non-viewable area

highlighted in yellow for a few seconds

after the bird’s-eye view is displayed.

Monitor, heater, air conditioner, audio and phone systems

4-13

4-14

Monitor, heater, air conditioner, audio and phone systems

In addition, the non-viewable corners

are displayed in red to remind the driver

to be cautious. When the rear sonar is

active, non-viewable corners

for the

rear side of the vehicle are not displayed.

(See “Rear Sonar System (RSS)” (P.5-136).)

WARNING

Objects in the bird’s-eye view will

appear farther than the actual

distance.

Tall objects, such as a curb or

vehicle, may be misaligned or not

displayed at the seam of the

views.

Objects that are above the cam-

era cannot be displayed.

The view for the bird’s-eye view

may be misaligned when the

camera position alters.

A line on the ground may be

misaligned and is not seen as

being straight at the seam of the

views. The misalignment will in-

crease as the line proceeds away

from the vehicle.

SAA3571

Front-side view:
Guiding lines:

Guiding lines that indicate the approx-

imate width and the front end of the

vehicle are displayed on the monitor.
The front-of-vehicle line

shows the

front part of the vehicle.
The side-of-vehicle line

shows the

vehicle width including the outside mir-

rors.
The extensions

of both the front

and

side

lines are shown with a green

dotted line.

DIFFERENCE BETWEEN PREDICTIVE

AND ACTUAL DISTANCES

The displayed guidelines and their loca-

tions on the ground are for approximate

reference only. Objects on uphill or down-

hill surfaces or projecting objects will be

actually located at distances different

from those displayed in the monitor

relative to the guidelines (refer to illustra-

tions). When in doubt, turn around and

view the objects as you are backing up, or

park and exit the vehicle to view the

positioning of objects behind the vehicle.

JVH1159X

Backing up on a steep uphill

When backing up the vehicle up a hill, the

distance guide lines and the vehicle width

guide lines are shown closer than the

actual distance. Note that any object on

the hill is farther than it appears on the

monitor.

JVH1160X

Backing up on a steep downhill

When backing up the vehicle down a hill,

the distance guide lines and the vehicle

width guide lines are shown farther than

the actual distance. Note that any object

on the hill is closer than it appears on the

monitor.

SAA1923

Backing up near a projecting object

The predictive course lines

do not

touch the object in the display. However,

the vehicle may hit the object if it projects

over the actual backing up course.

Monitor, heater, air conditioner, audio and phone systems

4-15

4-16

Monitor, heater, air conditioner, audio and phone systems

SAA3475

Backing up behind a projecting

object

The position

is shown farther than the

position

in the display. However, the

position

is actually at the same dis-

tance as the position

. The vehicle may

hit the object when backing up to the

position

if the object projects over the

actual moving course.

HOW TO PARK WITH PREDICTIVE

COURSE LINES

WARNING

If the tires are replaced with

different sized tires, the predic-

tive course lines may be dis-

played incorrectly.

On a snow-covered or slippery

road, there may be a difference

between the predictive course

line and the actual course line.

If the battery is disconnected or

becomes discharged, the predic-

tive course lines may be dis-

played incorrectly. If this occurs,

please perform the following pro-

cedures:
— Turn the steering wheel from

lock to lock while the engine is

running.

— Drive the vehicle on a straight

road for more than 5 minutes.

When the steering wheel is

turned with the ignition switch in

the ON position, the predictive

course lines may be displayed

incorrectly.

SAA1897

1. Visually check that the parking space

is safe before parking your vehicle.

2. The rear view of the vehicle is dis-

played on the screen

when the shift

lever is moved to the R (Reverse)

position.

SAA1898

3. Slowly back up the vehicle adjusting

the steering wheel so that the pre-

dictive course lines

enter the park-

ing space

4. Maneuver the steering wheel to make

the vehicle width guide lines

parallel

to the parking space

while referring

to the predictive course lines.

5. When the vehicle is parked in the

space completely, move the shift lever

to the P (Park) position and apply the

parking brake.

HOW TO SWITCH THE DISPLAY

With the ignition switch placed in the ON

position, push the CAMERA button or

move the shift lever to the R (Reverse)

position to operate the Intelligent Around

View® Monitor.
The Intelligent Around View® Monitor dis-

plays different split screen views depend-

ing on the position of the shift lever. Push

the CAMERA button to switch between

the available views.
If the shift lever is in the R (Reverse)

position, the available views are:

Rear view/bird’s-eye view split screen

Rear view/front-side view split screen

Rear view

If the shift lever is in the out of R (Reverse)

position, the available views are:

Front view/bird’s-eye view split screen

Front view/front-side view split screen

The display will switch from the Intelligent

Around View® Monitor screen when:

The shift lever is in the D (Drive)

position and the vehicle speed in-

creases above approximately 6 MPH

(10 km/h).

Monitor, heater, air conditioner, audio and phone systems

4-17

4-18

Monitor, heater, air conditioner, audio and phone systems

A different screen is selected.

WAE0058X

ADJUSTING THE SCREEN

1. Push the MENU button.
2. Touch the “Settings” key and then

touch the “Camera” key.

3. Touch the “Display Settings” key.
4. Touch the “Brightness”, “Contrast”,

“Tint”, “Color”, or “Black Level” key.

5. Adjust the item by touching the “+” or

“–” key on the touch screen display.

NOTE:
Do not adjust the display settings of the

Intelligent Around View® Monitor while

the vehicle is moving. Make sure the

parking brake is firmly applied.

INTELLIGENT AROUND VIEW®

MONITOR SYSTEM LIMITATIONS

WARNING

Listed below are the system limita-

tions for Intelligent Around View®

Monitor. Failure to operate the vehi-

cle in accordance with these system

limitations could result in serious

injury or death.

Do not use the Intelligent Around

View® Monitor with the outside

mirrors in the stored position,

and make sure that the liftgate

is securely closed when operating

the vehicle using the Intelligent

Around View® Monitor.

The apparent distance between

objects viewed on the Intelligent

Around View® Monitor differs

from the actual distance.

The cameras are installed above

the front grille, the outside mir-

rors and above the rear license

plate. Do not put anything on the

cameras.

When washing the vehicle with

highpressure water, be sure not

to spray it around the cameras.

Otherwise, water may enter the

camera unit causing water con-

densation on the lens, a malfunc-

tion, fire or an electric shock.

Do not strike the cameras. They

are precision instruments. Doing

so could cause a malfunction or

cause damage resulting in a fire

or an electric shock.

WAE0060X

There are some areas where the system

will not show objects and the system

does not warn of moving objects. When in

the front or the rear view display, an

object below the bumper or on the

ground may not be viewed

. When in

the bird’s-eye view, a tall object near the

seam

of the camera viewing areas will

not appear in the monitor.
The following are operating limitations

and do not represent a system malfunc-

tion:

There may be a delay when switching

between views.

When the temperature is extremely

high or low, the screen may not

display objects clearly.

When strong light directly shines on

the camera, objects may not be dis-

played clearly.

The screen may flicker under fluores-

cent light.

The colors of objects on the Intelligent

Around View® Monitor may differ

somewhat from the actual color of

objects.

Objects on the Intelligent Around

View® Monitor may not be clear and

the color of the object may differ in a

dark environment.

There may be differences in sharpness

between each camera view of the

bird’s-eye view.

Do not use wax on the camera lens.

Wipe off any wax with a clean cloth

that has been dampened with a

diluted mild cleaning agent, then wipe

with a dry cloth.

Monitor, heater, air conditioner, audio and phone systems

4-19

4-20

Monitor, heater, air conditioner, audio and phone systems

WAE0056X

System temporarily unavailable

When the “

” icon is displayed on the

screen, there will be abnormal conditions

in the Intelligent Around View® Monitor.

This will not hinder normal driving opera-

tion but the system should be inspected.

It is recommended you visit a NISSAN

dealer.

WAE0057X

When the “

” icon is displayed on the

screen, the camera image may be receiv-

ing temporary electronic disturbances

from surrounding devices. This will not

hinder normal driving operation but the

system should be inspected. It is recom-

mended you visit a NISSAN dealer.

WAE0211X

SYSTEM MAINTENANCE

CAUTION

Do not use alcohol, benzine or

thinner to clean the camera. This

will cause discoloration.

Do not damage the camera as the

monitor screen may be adversely

affected.

If dirt, rain or snow accumulates on any of

the cameras

, the Intelligent Around

View® Monitor may not display objects

clearly. Clean the camera by wiping with a

cloth dampened with a diluted mild

cleaning agent and then wiping with a

dry cloth.

WAE0016X

1. CAMERA button

WARNING

Failure to follow the warnings

and instructions for proper use

of the Moving Object Detection

system could result in serious

injury or death.

The MOD system is not a substi-

tute for proper vehicle operation

and is not designed to prevent

contact with objects surrounding

the vehicle. When maneuvering,

Monitor, heater, air conditioner, audio and phone systems

4-21

MOVING OBJECT DETECTION

(MOD) (if so equipped)

4-22

Monitor, heater, air conditioner, audio and phone systems

always use the outside mirror

and rearview mirror and turn

and check the surroundings to

ensure it is safe to maneuver.

The system is deactivated at

speeds above 5 MPH (8 km/h). It

is reactivated at lower speeds.

The MOD system is not designed

to detect the surrounding sta-

tionary objects.

The MOD system can inform the driver of

moving objects near the vehicle when

driving out of garages, maneuvering in

parking lots and in other such instances.
The MOD system detects moving objects

by using image processing technology on

the image shown in the display.

MOD SYSTEM OPERATION

The MOD system will turn on automati-

cally under the following conditions:

When the shift lever is in the R

(Reverse) position.

When the CAMERA button is pushed

to activate the Intelligent Around

View® Monitor system on the display.

When vehicle speed decreases below

approximately 5 MPH (8 km/h).

The MOD system operates in the follow-

ing conditions when the camera view is

displayed:

When the shift lever is in the P (Park) or

N (Neutral) position and the vehicle is

stopped, the MOD system detects the

moving objects in the bird’s-eye view.

The MOD system will not operate if

either door is opened. If outside mir-

rors are folded, MOD may not operate

properly.

When the shift lever is in the D (Drive)

position, and the vehicle speed is

below approximately 5 MPH (8 km/h),

the MOD system detects moving ob-

jects in the front view.

When the shift lever is in the R

(Reverse) position and the vehicle

speed is below approximately 5 MPH

(8 km/h), the MOD system detects

moving objects in the rear view. The

MOD system will not operate if the

liftgate is open.

The MOD system does not detect moving

objects in the front-side view. The MOD

icon is not displayed on the screen when

in this view.
When the MOD system detects a moving

object near the vehicle, the yellow frame

will be displayed on the view where the

object is detected and a chime will sound

once. While the MOD system continues to

detect moving objects, the yellow frame

continues to be displayed.

NOTE:
While the RCTA chime (if so equipped) is

beeping, the MOD system does not

chime.

JVH1256X

Front and bird’s-eye views

JVH0873X

Rear and bird’s-eye views

JVH1257X

Rear and front-side views

WAE0067X

Rear view

In the bird’s-eye view, the yellow frame

is displayed on each camera image (front,

rear, right, left) depending on where

moving objects are detected.
The yellow frame

is displayed on each

view in the front view and rear view

modes.
A blue MOD icon

is displayed in the view

where the MOD system is operative. A

gray MOD icon

is displayed in the view

where the MOD system is not operative.
If the MOD system is turned off, the MOD

icon

is not displayed.

TURNING MOD ON AND OFF

The MOD system can be turned on and

off using the vehicle information display.

(See “Driver Assistance” (P.2-21).)

MOD SYSTEM LIMITATIONS

WARNING

Listed below are the system limita-

tions for MOD. Failure to operate the

vehicle in accordance with these

system limitations could result in

serious injury or death.

Excessive noise (for example,

audio system volume or open

vehicle window) will interfere

with the chime sound, and it

Monitor, heater, air conditioner, audio and phone systems

4-23

4-24

Monitor, heater, air conditioner, audio and phone systems

may not be heard.

The MOD system performance

will be limited according to en-

vironmental conditions and sur-

rounding objects such as:
— When there is low contrast

between background and the

moving objects.

— When there is blinking source

of light.

— When strong light such as

another vehicle’s headlight or

sunlight is present.

— When camera orientation is

not in its usual position, such

as when the outside mirror is

folded.

— When there is dirt, water drops

or snow on the camera lens.

— When the position of the mov-

ing objects in the display is

not changed.

The MOD system might detect

flowing water droplets on the

camera lens, white smoke from

the muffler, moving shadows, etc.

The MOD system may not func-

tion properly depending on the

speed, direction, distance or

shape of the moving objects.

If your vehicle sustains damage

to the parts where the camera is

installed, leaving it misaligned or

bent, the sensing zone may be

altered and the MOD system may

not detect objects properly.

When the temperature is extre-

mely high or low, the screen may

not display objects clearly. This is

not a malfunction.

NOTE:
The blue MOD icon will change to

orange if one of the following has

occurred.

When the system is malfunctioning.

When the component temperature

reaches a high level (icon will blink).

When the rear view camera has

detected a blockage (icon will blink).

If the icon light continues to illuminate

orange, have the MOD system checked.

It is recommended that you visit a

NISSAN dealer for this service.

WAE0211X

SYSTEM MAINTENANCE

CAUTION

Do not use alcohol, benzine or

thinner to clean the camera. This

will cause discoloration.

Do not damage the camera as the

monitor screen may be adversely

affected.

If dirt, rain or snow accumulates on any of

the cameras , the MOD system may not

operate properly. Clean the camera by

wiping with a cloth dampened with a

diluted mild cleaning agent and then

wiping with a dry cloth.

JVH0662X

CENTER VENTILATORS

Open/close the ventilators by moving the

control to either direction.

This symbol indicates that the venti-

lators are open. Moving the control to

this direction will open the ventilators.

This symbol indicates that the venti-

lators are closed. Moving the control

to this direction will close the ventila-

tors.

Adjust the air flow direction of the venti-

lators by moving the center knob (up/

down, left/right) until the desired position

is achieved.

JVH0663X

SIDE VENTILATORS

Open/close the ventilators by moving the

control to either direction.

This symbol indicates that the venti-

lators are open. Moving the control to

this direction will open the ventilators.

This symbol indicates that the venti-

lators are closed. Moving the control

to this direction will close the ventila-

tors.

Adjust the air flow direction of the venti-

lators by moving the center knob (up/

down, left/right) until the desired position

is achieved.

Monitor, heater, air conditioner, audio and phone systems

4-25

VENTILATORS

4-26

Monitor, heater, air conditioner, audio and phone systems

JVH0879X

REAR VENTILATORS (if so equipped)

Open/close the ventilators by moving the

control to either direction.

This symbol indicates that the venti-

lators are open. Moving the side

control to this direction will open the

ventilators.

This symbol indicates that the venti-

lators are closed. Moving the side

control to this direction will close the

ventilators.

Adjust the air flow direction of the venti-

lators by moving the center knob (up/

down, left/right) until the desired position

is achieved.

WARNING

The heater and air conditioner

operate only when the engine is

running.

Never leave children or adults

who would normally require the

support of others alone in the

vehicle. Pets should not be left

alone either. They could unknow-

ingly activate switches or con-

trols and inadvertently become

involved in a serious accident

and injure themselves. On hot,

sunny days, temperatures in a

closed vehicle could quickly be-

come high enough to cause se-

vere or possibly fatal injuries to

people or animals.

Do not use the recirculation mode

for long periods as it may cause

the interior air to become stale

and the windows to fog up.

Do not adjust the heating and air

conditioning controls while driv-

ing so that full attention may be

given to vehicle operation.

The heater and air conditioner operate

when the engine is running. The air

blower will operate even if the engine is

turned off and the ignition switch is

placed in the ON position.

NOTE:

Odors from inside and outside the

vehicle can build up in the air condi-

tioner unit. Odor can enter the pas-

senger compartment through the

ventilators.

When parking, set the heater and air

conditioner controls to turn off air

recirculation to allow fresh air into

the passenger compartment. This

should help reduce odors inside the

vehicle.

HEATER AND AIR CONDITIONER

JVH0664X

A/C button/Fan speed control

dial

Air flow control buttons

MAX A/C button/Temperature control

dial

Front defroster

button

Rear defroster

button (See “Rear

window and outside mirror defroster

switch” (P.2-51).)

Air recirculation

button

MANUAL AIR CONDITIONER AND

HEATER
Controls

Turning system on/off:

To turn on the system, turn the fan speed

control

dial out of the OFF position.

Turn the dial counterclockwise to the OFF

position to turn off the system.

Fan speed control:

Turn the fan speed control

dial

clockwise to increase the fan speed.
Turn the fan speed control

dial

counterclockwise to decrease the fan

speed.

Temperature control:

Turn the temperature control dial to set

the desired temperature. Turn the dial

between the middle and the right posi-

tion to select the hot temperature. Turn

the dial between the middle and the left

position to select the cool temperature.

Air flow control:

Push one of the air flow control buttons

to select the air flow outlets.

— Air flows mainly from center and side

ventilators.

— Air flows mainly from center and side

ventilators and foot outlets.

— Air flows mainly from the foot outlet

and partly from the defroster.

— Air flows mainly from the defroster

and foot outlets.

Air intake control:

The air intake control mode will change

each time the air recirculation

button

is pushed.

When the indicator light is turned on,

the air recirculates inside the vehicle.

When the indicator light is turned off,

the air flow is drawn from outside the

vehicle.

Monitor, heater, air conditioner, audio and phone systems

4-27

4-28

Monitor, heater, air conditioner, audio and phone systems

A/C (Air Conditioner) operation:

Push the A/C button to turn on or off the

air conditioner. When the air conditioner

is on, the A/C indicator light on the button

illuminates.

MAX A/C (Quick Air Conditioning) op-
eration:

Push the MAX A/C button for maximum

cooling and dehumidifying.
When the MAX A/C mode is turned on, the

air flow mode indicator will turn off with

the air flow mode fixed at

At the same time, the indicator light on

the A/C button and the air recirculation

mode will turn on.
Push the MAX A/C button again to turn

off the MAX A/C mode. When the MAX A/C

mode is turned off, most of the settings

will return to the previous state, while the

indicator light on the A/C button will stay

on.

Heater operation

Heating:

This mode is used to direct heated air

from the foot outlets. Some air also flows

from the defroster outlets and the side

ventilator outlets.
1. Push the air recirculation

button

for normal heating. (The indicator light

will turn off.)

2. Push the

button. (The indicator

light will turn on.)

3. Turn the fan speed control

dial to

the desired position.

4. Turn the temperature control dial to

the desired position between the

middle and the hot (right) position.

Ventilation:

This mode directs outside air from the

side and center ventilators.
1. Push the air recirculation

button.

(The indicator light will turn off.)

2. Push the

button. (The indicator

light will turn on.)

3. Turn the fan speed control

dial to

the desired position.

4. Turn the temperature control dial to

the desired position.

Defrosting or defogging:

This mode directs the air to the defroster

outlets to defrost/defog the windows.
1. Push the front defroster

button.

(The indicator light will turn on.)

2. Turn the fan speed control

dial to

the desired position.

3. Turn the temperature control dial to

the desired position between the

middle and the hot (right) position.
To remove frost from the windshield

quickly, turn the temperature control

dial to the maximum hot (right) posi-

tion and the fan speed control

dial

to the maximum position.
When the front defroster mode is

selected, the air conditioner automa-

tically turns on if the outside tempera-

ture is more than 36°F (2°C). This

dehumidifies the air which helps defog

the windshield. The air recirculation

indicator automatically turns off, al-

lowing outside air to be drawn into

the passenger compartment to

further improve the defogging perfor-

mance. The recirculation mode can-

not be activated in the front defroster

mode.

Bi-level heating:

The bi-level mode directs warmed air to

Content .. 12 13 14 15 ..