Nissan Frontier D40. Manual - part 1074

 

  Index      Nissan     Nissan Frontier D40 (2010 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1072  1073  1074  1075   ..

 

 

Nissan Frontier D40. Manual - part 1074

 

 

TM-194

< COMPONENT DIAGNOSIS >

[5AT: RE5R05A]

P1730 INTERLOCK

P1730 INTERLOCK

Description

INFOID:0000000005274100

Fail-safe function to detect interlock conditions.

On Board Diagnosis Logic

INFOID:0000000005274101

• This is an OBD-II self-diagnostic item.
• Diagnostic trouble code “P1730” with CONSULT-III or 12th judgment flicker without CONSULT-III is detected

when TCM does not receive the proper voltage signal from the sensor and switch.

• TCM monitors and compares gear position and conditions of each ATF pressure switch when gear is steady.

Possible Cause

INFOID:0000000005274102

• Harness or connectors

(The solenoid and switch circuit is open or shorted.)

• Low coast brake solenoid valve
• ATF pressure switch 2

DTC Confirmation Procedure

INFOID:0000000005274103

NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.

 WITH CONSULT-III

1.

Turn ignition switch “ON”. (Do not start engine.)

2.

Select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.

3.

Start engine.

4.

Drive vehicle and maintain the following conditions for at least 2 consecutive seconds.
SLCT LVR POSI: “D” position 

5.

If DTC is detected, go to 

TM-194, "Diagnosis Procedure"

.

 WITH GST

Follow the procedure “WITH CONSULT-III”.

Judgement of Interlock

INFOID:0000000005274104

When interlock is judged to be malfunctioning, the vehicle should be fixed in 2GR, and should be set in a con-
dition in which it can travel.
When one of the following fastening patterns is detected, the fail-safe function in correspondence with the indi-
vidual pattern should be performed.
NOTE:
When the vehicle is driven in 2GR, a input speed sensor malfunction is displayed, but this is not a
input speed sensor malfunction.
When interlock is detected at the 3GR or more, it is locked at the 2GR.

Diagnosis Procedure

INFOID:0000000005274105

1.

SELF-DIAGNOSIS

With CONSULT-III

1.

Drive vehicle.

2.

Stop vehicle and turn ignition switch OFF.

3.

Turn ignition switch ON.

4.

Select “SELF-DIAG RESULTS” mode for “TRANSMISSION” with CONSULT-III.

Without CONSULT-III

1.

Drive vehicle.

2.

Stop vehicle and turn ignition switch OFF.

3.

Turn ignition switch ON.

P1730 INTERLOCK

TM-195

< COMPONENT DIAGNOSIS >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

4.

Perform self-diagnosis. Refer to 

TM-156, "Diagnosis Procedure without CONSULT-III"

.

 OK or NG

OK

>> GO TO 2.

NG

>> Check low coast brake solenoid valve circuit and function. Refer to 

TM-206

TM-208

.

2.

CHECK DTC

Perform “DTC Confirmation Procedure”.
• Refer to 

TM-194, "DTC Confirmation Procedure"

.

OK or NG

OK

>> INSPECTION END

NG

>> GO TO 3.

3.

CHECK TCM POWER SUPPLY AND GROUND CIRCUIT

Check TCM power supply and ground circuit. Refer to 

TM-210, "Diagnosis Procedure"

.

OK or NG

OK

>> GO TO 4.

NG

>> Repair or replace damaged parts.

4.

DETECT MALFUNCTIONING ITEM

Check the following.
• The A/T assembly harness connector pin terminals for damage or loose connection with harness connector.

OK or NG

OK

>> Replace the control valve with TCM. Refer to 

TM-280, "Removal and Installation"

.

NG

>> Repair or replace damaged parts.

TM-196

< COMPONENT DIAGNOSIS >

[5AT: RE5R05A]

P1731 1ST ENGINE BRAKING

P1731 1ST ENGINE BRAKING

Description

INFOID:0000000005274106

Fail-safe function to prevent sudden decrease in speed by engine brake other than at “1” position.

CONSULT-III Reference Value in Data Monitor Mode

INFOID:0000000005274107

On Board Diagnosis Logic

INFOID:0000000005274108

• This is not an OBD-II self-diagnostic item.
• Diagnostic trouble code “P1731” with CONSULT-III or 13th judgment flicker without CONSULT-III is detected

under the following conditions.

- When TCM does not receive the proper voltage signal from the sensor.
- When TCM monitors each ATF pressure switch and solenoid monitor value, and detects as irregular when

engine brake of 1GR acts other than at “1” position.

Possible Cause

INFOID:0000000005274109

• Harness or connectors

(The sensor circuit is open or shorted.)

• Low coast brake solenoid valve
• ATF pressure switch 2

DTC Confirmation Procedure

INFOID:0000000005274110

NOTE:
If “DTC Confirmation Procedure” has been previously preformed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.

 WITH CONSULT-III

1.

Turn ignition switch “ON”. (Do not start engine.)

2.

Select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.

3.

Start engine.

4.

Drive vehicle and maintain the following conditions for at least 2 consecutive seconds.
ENGINE SPEED: 1,200 rpm
SLCT LVR POSI: “1” position 
GEAR: 1st 

5.

If DTC is detected, go to 

TM-196, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000005274111

1.

CHECK INPUT SIGNALS

With CONSULT-III

1.

Start the engine.

2.

Select “SELECTION FROM MENU” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.

3.

Drive vehicle in the “1” position (1GR), and confirm the ON/OFF actuation of “ATF PRES SW 2” and “ON
OFF SOL”.

OK or NG

OK

>> GO TO 4.

NG

>> GO TO 2.

Item name

Condition 

Display value

ON OFF SOL

Low coast brake engaged. Refer to 

TM-128

.

ON

Low coast brake disengaged. Refer to 

TM-128

.

OFF

ATF PRES SW 2

Low coast brake engaged. Refer to 

TM-128

.

ON

Low coast brake disengaged. Refer to 

TM-128

.

OFF

P1731 1ST ENGINE BRAKING

TM-197

< COMPONENT DIAGNOSIS >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

2.

CHECK TCM POWER SUPPLY AND GROUND CIRCUIT

Check TCM power supply and ground circuit. Refer to 

TM-210, "Diagnosis Procedure"

.

OK or NG

OK

>> GO TO 3.

NG

>> Repair or replace damaged parts.

3.

DETECT MALFUNCTIONING ITEM

Check the following.
• The A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG

OK

>> Replace the control valve with TCM. Refer to 

TM-280, "Removal and Installation"

.

NG

>> Repair or replace damaged parts.

4.

CHECK DTC

Perform “DTC Confirmation Procedure”.
• Refer to 

TM-196, "DTC Confirmation Procedure"

.

OK or NG

OK

>> INSPECTION END

NG

>> GO TO 2.

 

 

 

 

 

 

 

Content   ..  1072  1073  1074  1075   ..