Nissan Quest E52. Manual - part 417

 

  Index      Nissan     Nissan Quest E52 (2011-2014 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  415  416  417  418   ..

 

 

Nissan Quest E52. Manual - part 417

 

 

DLK-382

< SYMPTOM DIAGNOSIS >

P RANGE INTERLOCK DOOR LOCK/UNLOCK FUNCTION DOES NOT OPER-

ATE

P RANGE INTERLOCK DOOR LOCK/UNLOCK FUNCTION DOES NOT OP-
ERATE

Diagnosis Procedure

INFOID:0000000009649346

1.

CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT”

1.

Select “DOOR LOCK” of “BCM” using CONSULT.

2.

Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mode.

3.

Check “AUTOMATIC LOCK/UNLOCK SELECT” setting in “WORK SUPPORT”.
Refer to 

DLK-94, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Set “Unlock Only”, “Lock Only” or “Lock/Unlock” in “AUTOMATIC LOCK/UNLOCK SELECT”.

2.

CHECK “AUTOMATIC DOOR LOCK SELECT” SETTING IN “WORK SUPPORT”

1.

Select “DOOR LOCK” of “BCM” using CONSULT.

2.

Select “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT” mode.

3.

Check “AUTOMATIC DOOR LOCK SELECT” setting in “WORK SUPPORT”.
Refer to 

DLK-94, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Set “P RANGE” in “AUTOMATIC DOOR LOCK SELECT”.

3.

CHECK “AUTOMATIC DOOR UNLOCK SELECT” SETTING IN “WORK SUPPORT”

1.

Select “DOOR LOCK” of “BCM” using CONSULT.

2.

Select “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT” mode.

3.

Check “AUTOMATIC DOOR UNLOCK SELECT” setting in “WORK SUPPORT”.
Refer to 

DLK-94, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Set “MODE 2” or “MODE 4” in “AUTOMATIC DOOR UNLOCK SELECT”.

4.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-98, "Removal and Installation"

.

2.

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-42, "Intermittent Incident"

.

HAZARD AND HORN REMINDER DOES NOT OPERATE

DLK-383

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

HAZARD AND HORN REMINDER DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000009649347

1.

CHECK “HAZARD ANSWER BACK” SETTING IN “WORK SUPPORT”

1.

Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2.

Select “HAZARD ANSWER BACK” in “WORK SUPPORT” mode.

3.

Check the “HAZARD ANSWER BACK” setting in “WORK SUPPORT”.
Refer to 

DLK-95, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Set the “Lock Only”, “Unlock Only” or “Lock/Unlock” in “HAZARD ANSWER BACK”.

2.

CHECK “HORN WITH KEYLESS LOCK” SETTING IN “WORK SUPPORT”

1.

Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2.

Select “HORN WITH KEYLESS LOCK” in “WORK SUPPORT” mode.

3.

Check the “HORN WITH KEYLESS LOCK” in “WORK SUPPORT”.
Refer to 

DLK-95, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Set the “On” in “HORN WITH KEYLESS LOCK”.

3.

CHECK HAZARD FUNCTION

Check hazard function.
Refer to 

DLK-279, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

CHECK HORN FUNCTION

Check horn function.
Refer to 

SEC-120, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-98, "Removal and Installation"

.

2.

Confirm the operation after replacement. 

Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-42, "Intermittent Incident"

.

DLK-384

< SYMPTOM DIAGNOSIS >

HAZARD AND BUZZER REMINDER DOES NOT OPERATE

HAZARD AND BUZZER REMINDER DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000009649348

1.

CHECK “HAZARD ANSWER BACK” SETTING IN “WORK SUPPORT”

1.

Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2.

Select “HAZARD ANSWER BACK” in “WORK SUPPORT” mode.

3.

Check the “HAZARD ANSWER BACK” setting in “WORK SUPPORT”.
Refer to 

DLK-95, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Set the “Lock Only”, “Unlock Only” or “Lock/Unlock” in “HAZARD ANSWER BACK”.

2.

CHECK “ANS BACK I-KEY LOCK” SETTING IN “WORK SUPPORT”

1.

Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2.

Select “ANS BACK I-KEY LOCK” in “WORK SUPPORT” mode.

3.

Check the “ANS BACK I-KEY LOCK”setting in “WORK SUPPORT”.
Refer to 

DLK-95, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Set the “Horn Chirp” or “Buzzer” in “ANS BACK I-KEY LOCK”.

3.

CHECK “ANS BACK I-KEY UNLOCK” SETTING IN “WORK SUPPORT”

1.

Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2.

Select “ANS BACK I-KEY UNLOCK” in “WORK SUPPORT” mode.

3.

Check the “ANS BACK I-KEY UNLOCK” setting in “WORK SUPPORT”.
Refer to 

DLK-95, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Set the “On” in “ANS BACK I-KEY UNLOCK”.

4.

CHECK HAZARD FUNCTION

Check hazard function.
Refer to 

DLK-279, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

CHECK INTELLIGENT KEY WARNING BUZZER

Check Intelligent Key warning buzzer.
Refer to 

DLK-273, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace the malfunctioning parts.

6.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-98, "Removal and Installation"

.

2.

Confirm the operation after replacement. 

Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-42, "Intermittent Incident"

.

KEY REMINDER FUNCTION DOES NOT OPERATE

DLK-385

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

KEY REMINDER FUNCTION DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000009649349

1.

CHECK DTC WITH BCM

Check that DTC is not detected with BCM.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Refer to 

BCS-63, "DTC Index"

.

2.

CHECK “ANTI KEY LOCK IN FUNCTI” SETTING IN “WORK SUPPORT”

1.

Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2.

Select “ANTI KEY LOCK IN FUNCTI” in “WORK SUPPORT” mode.

3.

Check “ANTI KEY LOCK IN FUNCTI” setting in “WORK SUPPORT”.
Refer to 

DLK-95, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Set “On” in “ANTI KEY LOCK IN FUNCTI”.

3.

CHECK DOOR SWITCH

Check door switch
Refer to 

DLK-241, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

CHECK INSIDE KEY ANTENNA

Check inside key antenna.
• Instrument center: Refer to 

DLK-226, "DTC Logic"

.

• Console: Refer to 

DLK-228, "DTC Logic"

.

• Luggage room: Refer to 

DLK-230, "DTC Logic"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

CHECK UNLOCK SENSOR

Check unlock sensor.
Refer to 

DLK-259, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace the malfunctioning parts.

6.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-98, "Removal and Installation"

.

2.

Confirm the operation after replacement. 

Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-42, "Intermittent Incident"

.

 

 

 

 

 

 

 

Content   ..  415  416  417  418   ..