Nissan Quest E52. Manual - part 410

DLK-354

< DTC/CIRCUIT DIAGNOSIS >

SLIDING DOOR TOUCH SENSOR

3.

Check continuity between sliding door control unit RH harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK SLIDING DOOR TOUCH SENSOR GROUND CIRCUIT 2

1.

Connect sliding door control unit RH connector and sliding door touch sensor RH connector.

2.

Check voltage between sliding door control unit RH harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace sliding door control unit RH. Refer to 

DLK-500, "LH : Removal and Installation"

.

5.

CHECK SLIDING DOOR TOUCH SENSOR

Refer to 

DLK-354, "SLIDING DOOR RH : Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Replace sliding door touch sensor RH.

6.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-42, "Intermittent Incident"

.

>> INSPECTION END

SLIDING DOOR RH : Component Inspection

INFOID:0000000009649306

1.

CHECK SLIDING DOOR TOUCH SENSOR RH

1.

Turn ignition switch OFF.

2.

Disconnect sliding door touch sensor RH connector.

3.

Check resistance between sliding door touch sensor RH terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace sliding door touch sensor RH.

Sliding door control unit RH

Sliding door touch sensor RH

Continuity 

 Connector

Terminal

 Connector

Terminal

B247

23

D173

2

Existed

Sliding door control unit RH

Ground

Continuity 

 Connector

Terminal

B247

23

Not existed

(+)

(–)

Voltage

Sliding door control unit RH

 Connector

Terminal

B247

23

Ground

0 V

Sliding door touch sensor RH

 Condition

Resistance 

Terminal

1

2

Sliding door touch sen-
sor RH

Detect obstruction

120 

Ω

 or less

Other than above

1 k

Ω

 

±

 10%

CLUTCH

DLK-355

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

CLUTCH

SLIDING DOOR LH

SLIDING DOOR LH : Component Function Check

INFOID:0000000009649307

1.

CHECK FUNCTION

1.

Select “AUTO SLIDE DOOR” using CONSULT.

2.

Select “CLUTCH” in “ACTIVE TEST” mode.

3.

Touch “HOLD” and “RELEASE” to check that it works normally.

Is the inspection result normal?

YES

>> Clutch is OK.

NO

>> Refer to 

DLK-355, "SLIDING DOOR LH : Diagnosis Procedure"

.

SLIDING DOOR LH : Diagnosis Procedure

INFOID:0000000009649308

1.

CHECK CLUTCH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect automatic sliding door unit LH connector.

3.

Check voltage between automatic sliding door unit LH harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK CLUTCH CIRCUIT

1.

Disconnect sliding door control unit LH connector.

2.

Check continuity between sliding door control unit LH harness connector and automatic sliding door unit
LH harness connector.

3.

Check continuity between sliding door control unit LH harness connector and ground.

Is the inspection result normal?

YES

>> Replace sliding door control unit LH. Refer to 

DLK-500, "LH : Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK CLUTCH GROUND CIRCUIT

1.

Disconnect sliding door control unit LH connector.

2.

Check continuity between sliding door control unit LH harness connector and automatic sliding door unit
LH harness connector.

(+)

(–)

Condition

Voltage

Automatic sliding door unit LH

 Connector

Terminal

B33

2

Ground

Clutch

ON

9 – 16 V

OFF

0 V

Sliding door control unit LH

Automatic sliding door unit LH

Continuity 

 Connector

Terminal

 Connector

Terminal

B47

47

B33

2

Existed

Sliding door control unit LH

Ground

Continuity 

 Connector

Terminal

B47

47

Not existed

DLK-356

< DTC/CIRCUIT DIAGNOSIS >

CLUTCH

3.

Check continuity between sliding door control unit LH harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK CLUTCH CIRCUIT 2

1.

Connect sliding door control unit LH connector and automatic sliding door unit LH connector.

2.

Check voltage between sliding door control unit LH harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic sliding door unit LH.

NO

>> Replace sliding door control unit LH. Refer to 

DLK-500, "LH : Removal and Installation"

.

SLIDING DOOR RH

SLIDING DOOR RH : Component Function Check

INFOID:0000000009649309

1.

CHECK FUNCTION

1.

Select “AUTO SLIDE DOOR RIGHT” using CONSULT.

2.

Select “CLUTCH” in “ACTIVE TEST” mode.

3.

Touch “HOLD” and “RELEASE” to check that it works normally.

Is the inspection result normal?

YES

>> Clutch is OK.

NO

>> Refer to 

DLK-355, "SLIDING DOOR LH : Diagnosis Procedure"

.

SLIDING DOOR RH : Diagnosis Procedure

INFOID:0000000009649310

1.

CHECK CLUTCH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect automatic sliding door unit RH connector.

3.

Check voltage between automatic sliding door unit RH harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK CLUTCH CIRCUIT

Sliding door control unit LH

Automatic sliding door unit LH

Continuity 

 Connector

Terminal

 Connector

Terminal

B47

44

B33

1

Existed

Sliding door control unit LH

Ground

Continuity 

 Connector

Terminal

B47

44

Not existed

(+)

(–)

Voltage

Sliding door control unit LH

 Connector

Terminal

B47

44

Ground

0 V

(+)

(–)

Condition

Voltage

Automatic sliding door unit RH

 Connector

Terminal

B245

2

Ground

Clutch

ON

9 – 16 V

OFF

0 V

CLUTCH

DLK-357

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

1.

Disconnect sliding door control unit RH connector.

2.

Check continuity between sliding door control unit RH harness connector and automatic sliding door unit
RH harness connector.

3.

Check continuity between sliding door control unit RH harness connector and ground.

Is the inspection result normal?

YES

>> Replace sliding door control unit RH. Refer to 

DLK-500, "RH : Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK CLUTCH GROUND CIRCUIT

1.

Disconnect sliding door control unit RH connector.

2.

Check continuity between sliding door control unit RH harness connector and automatic sliding door unit
RH harness connector.

3.

Check continuity between sliding door control unit RH harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK CLUTCH CIRCUIT 2

1.

Connect sliding door control unit RH connector and automatic sliding door unit RH connector.

2.

Check voltage between sliding door control unit RH harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic sliding door unit RH.

NO

>> Replace sliding door control unit RH. Refer to 

DLK-500, "RH : Removal and Installation"

.

Sliding door control unit RH

Automatic sliding door unit RH

Continuity 

 Connector

Terminal

 Connector

Terminal

B249

47

B245

2

Existed

Sliding door control unit RH

Ground

Continuity 

 Connector

Terminal

B249

47

Not existed

Sliding door control unit RH

Automatic sliding door unit RH

Continuity 

 Connector

Terminal

 Connector

Terminal

B249

44

B245

1

Existed

Sliding door control unit RH

Ground

Continuity 

 Connector

Terminal

B249

44

Not existed

(+)

(–)

Voltage

Sliding door control unit RH

 Connector

Terminal

B249

44

Ground

0 V