Nissan Quest E52. Manual - part 408

 

  Index      Nissan     Nissan Quest E52 (2011-2014 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

  

 

Content   ..  406  407  408  409   ..

 

 

Nissan Quest E52. Manual - part 408

 

 

DLK-346

< DTC/CIRCUIT DIAGNOSIS >

SLIDING DOOR OPEN/CLOSE SWITCH

REAR RH : Component Inspection

INFOID:0000000009649294

1.

CHECK SLIDING DOOR OPEN/CLOSE SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect sliding door open/close switch (rear RH) connector.

3.

Check continuity between sliding door open/close switch (rear RH) terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace sliding door open/close switch (rear RH).

Sliding door open/close switch (rear RH)

Condition

Continuity

Terminal

1

2

Sliding door open/close switch 
(rear RH)

Pressed

Existed

Released

Not existed

SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH

DLK-347

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH

SLIDING DOOR LH

SLIDING DOOR LH : Component Function Check

INFOID:0000000009649295

1.

CHECK FUNCTION

1.

Select “AUTO SLDE DOOR” using CONSULT.

2.

Select “ONE-TOUCH SW” in “DATA MONITOR” mode.

3.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Sliding door one-touch open/close switch is OK.

NO

>> Refer to 

DLK-347, "SLIDING DOOR LH : Diagnosis Procedure"

.

SLIDING DOOR LH : Diagnosis Procedure

INFOID:0000000009649296

1.

CHECK SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect sliding door one-touch open/close switch LH connector.

3.

Check voltage between sliding door one-touch open/close switch LH harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH CIRCUIT

1.

Disconnect sliding door control unit LH connector.

2.

Check continuity between sliding door control unit LH harness connector and sliding door one-touch open/
close switch LH harness connector.

3.

Check continuity between sliding door control unit LH harness connector and ground.

Is the inspection result normal?

YES

>> Replace sliding door control unit LH. Refer to 

DLK-500, "LH : Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH GROUND CIRCUIT

1.

Disconnect sliding door control unit LH connector.

2.

Check continuity between sliding door control unit LH harness connector and sliding door one-touch open/
close switch LH harness connector.

Monitor item

Condition

Status

ONE-TOUCH SW

Sliding door one-touch open/
close switch LH

Pressed

ON

Released

OFF

(+)

(–)

Voltage

Sliding door one-touch open/close switch LH

Connector

Terminal

D125

1

Ground

8 – 16 V

Sliding door control unit LH

Sliding door one-touch open/close switch LH

Continuity 

Connector

Terminal

Connector

Terminal

B45

14

D125

1

Existed

Sliding door control unit LH

Ground

Continuity 

Connector

Terminal

B45

14

Not existed

DLK-348

< DTC/CIRCUIT DIAGNOSIS >

SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH

3.

Check continuity between sliding door control unit LH harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH CIRCUIT 2

1.

Connect sliding door control unit LH connector and sliding door one-touch open/close switch LH connec-
tor.

2.

Check voltage between sliding door one-touch open/close switch LH harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace sliding door control unit LH. Refer to 

DLK-500, "LH : Removal and Installation"

.

5.

CHECK SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH

Refer to 

DLK-348, "SLIDING DOOR LH : Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Replace sliding door one-touch open/close switch LH.

6.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-42, "Intermittent Incident"

.

>> INSPECTION END

SLIDING DOOR LH : Component Inspection

INFOID:0000000009649297

1.

CHECK SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect sliding door one-touch open/close switch LH connector.

3.

Check continuity between sliding door one-touch open/close switch LH terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace sliding door one-touch open/close switch LH.

SLIDING DOOR RH

Sliding door control unit LH

Sliding door one-touch open/close switch LH

Continuity 

Connector

Terminal

Connector

Terminal

B45

23

D125

2

Existed

Sliding door control unit LH

Ground

Continuity 

Connector

Terminal

B45

23

Not existed

(+)

(–)

Voltage

Sliding door control unit LH

Connector

Terminal

B45

23

Ground

0 V

Sliding door one-touch open/close switch 

LH

Condition

Continuity

Terminal

1

2

Sliding door one-touch open/
close switch LH

Pressed

Existed

Released

Not existed

SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH

DLK-349

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

SLIDING DOOR RH : Component Function Check

INFOID:0000000009649298

1.

CHECK FUNCTION

1.

Select “AUTO SLDE DOOR RIGHT” using CONSULT.

2.

Select “ONE-TOUCH SW” in “DATA MONITOR” mode.

3.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Sliding door one-touch open/close switch is OK.

NO

>> Refer to 

DLK-347, "SLIDING DOOR LH : Diagnosis Procedure"

.

SLIDING DOOR RH : Diagnosis Procedure

INFOID:0000000009649299

1.

CHECK SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect sliding door one-touch open/close switch RH connector.

3.

Check voltage between sliding door one-touch open/close switch RH harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH CIRCUIT

1.

Disconnect sliding door control unit RH connector.

2.

Check continuity between sliding door control unit RH harness connector and sliding door one-touch
open/close switch RH harness connector.

3.

Check continuity between sliding door control unit RH harness connector and ground.

Is the inspection result normal?

YES

>> Replace sliding door control unit RH. Refer to 

DLK-500, "RH : Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH GROUND CIRCUIT

1.

Disconnect sliding door control unit RH connector.

2.

Check continuity between sliding door control unit RH harness connector and sliding door one-touch
open/close switch RH harness connector.

Monitor item

Condition

Status

ONE-TOUCH SW

Sliding door one-touch open/
close switch RH

Pressed

ON

Released

OFF

(+)

(–)

Voltage

Sliding door one-touch open/close switch RH

Connector

Terminal

D126

1

Ground

8 – 16 V

Sliding door control unit RH

Sliding door one-touch open/close switch RH

Continuity 

Connector

Terminal

Connector

Terminal

B247

14

D126

1

Existed

Sliding door control unit RH

Ground

Continuity 

Connector

Terminal

B247

14

Not existed

 

 

 

 

 

 

 

Content   ..  406  407  408  409   ..