Nissan Quest E52. Manual - part 403

 

  Index      Nissan     Nissan Quest E52 (2011-2014 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

  

 

Content   ..  401  402  403  404   ..

 

 

Nissan Quest E52. Manual - part 403

 

 

DLK-326

< DTC/CIRCUIT DIAGNOSIS >

SLIDING DOOR HANDLE SWITCH

SLIDING DOOR HANDLE SWITCH

SLIDING DOOR LH

SLIDING DOOR LH : Component Function Check

INFOID:0000000009649262

1.

CHECK FUNCTION

1.

Select “AUTO SLDE DOOR” using CONSULT.

2.

Select “DOR HAND SW L” in “DATA MONITOR” mode.

3.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Sliding door handle switch is OK.

NO

>> Refer to 

DLK-326, "SLIDING DOOR LH : Diagnosis Procedure"

.

SLIDING DOOR LH : Diagnosis Procedure

INFOID:0000000009649263

1.

CHECK SLIDING DOOR HANDLE SWITCH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect remote control assembly LH connector.

3.

Check voltage between remote control assembly LH harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK SLIDING DOOR HANDLE SWITCH CIRCUIT

1.

Disconnect sliding door control unit LH connector.

2.

Check continuity between sliding door control unit LH harness connector and remote control assembly LH
harness connector.

3.

Check continuity between sliding door control unit LH harness connector and ground.

Is the inspection result normal?

YES

>> Replace sliding door control unit LH. Refer to 

DLK-500, "LH : Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK SLIDING DOOR HANDLE SWITCH GROUND CIRCUIT

1.

Disconnect sliding door control unit LH connector.

2.

Check continuity between sliding door control unit LH harness connector and remote control assembly LH
harness connector.

Monitor item

Condition

Status

DOR HAND SW L

Sliding door handle LH

Pull

ON

Release

OFF

(+)

(–)

Voltage

Remote control assembly LH

Connector

Terminal

D118

2

Ground

8 – 16 V

Sliding door control unit LH

Remote control assembly LH

Continuity 

Connector

Terminal

Connector

Terminal

B45

22

D118

2

Existed

Sliding door control unit LH

Ground

Continuity 

Connector

Terminal

B45

22

Not existed

SLIDING DOOR HANDLE SWITCH

DLK-327

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

3.

Check continuity between sliding door control unit LH harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK SLIDING DOOR HANDLE SWITCH CIRCUIT 2

1.

Connect sliding door control unit LH connector and remote control assembly LH connector.

2.

Check voltage between sliding door control unit LH harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace sliding door control unit LH. Refer to 

DLK-500, "LH : Removal and Installation"

.

5.

CHECK SLIDING DOOR HANDLE SWITCH

Refer to 

DLK-327, "SLIDING DOOR LH : Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Replace remote control assembly LH.

6.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-42, "Intermittent Incident"

.

>> INSPECTION END

SLIDING DOOR LH : Component Inspection

INFOID:0000000009649264

1.

CHECK SLIDING DOOR HANDLE SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect remote control assembly LH connector.

3.

Check continuity between remote control assembly LH terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace remote control assembly LH.

SLIDING DOOR RH

Sliding door control unit LH

Remote control assembly LH

Continuity 

Connector

Terminal

Connector

Terminal

B45

23

D118

1

Existed

Sliding door control unit LH

Ground

Continuity 

Connector

Terminal

B45

23

Not existed

(+)

(–)

Voltage

Sliding door control unit LH

Connector

Terminal

B45

23

Ground

0 V

Remote control assembly LH

Condition

Continuity

Terminal

2

1

Sliding door handle LH

Pull

Existed

Release

Not existed

DLK-328

< DTC/CIRCUIT DIAGNOSIS >

SLIDING DOOR HANDLE SWITCH

SLIDING DOOR RH : Component Function Check

INFOID:0000000009649265

1.

CHECK FUNCTION

1.

Select “AUTO SLDE DOOR RIGHT” using CONSULT.

2.

Select “DOR HAND SW R” in “DATA MONITOR” mode.

3.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Sliding door handle switch is OK.

NO

>> Refer to 

DLK-328, "SLIDING DOOR RH : Diagnosis Procedure"

.

SLIDING DOOR RH : Diagnosis Procedure

INFOID:0000000009649266

1.

CHECK SLIDING DOOR HANDLE SWITCH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect remote control assembly RH connector.

3.

Check voltage between remote control assembly RH harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK SLIDING DOOR HANDLE SWITCH CIRCUIT

1.

Disconnect sliding door control unit RH connector.

2.

Check continuity between sliding door control unit RH harness connector and remote control assembly
RH harness connector.

3.

Check continuity between sliding door control unit RH harness connector and ground.

Is the inspection result normal?

YES

>> Replace sliding door control unit RH. Refer to 

DLK-500, "RH : Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK SLIDING DOOR HANDLE SWITCH GROUND CIRCUIT

1.

Disconnect sliding door control unit RH connector.

2.

Check continuity between sliding door control unit RH harness connector and remote control assembly
RH harness connector.

Monitor item

Condition

Status

DOR HAND SW R

Sliding door handle RH

Pull

ON

Release

OFF

(+)

(–)

Voltage

Remote control assembly RH

Connector

Terminal

D127

2

Ground

8 – 16 V

Sliding door control unit RH

Remote control assembly RH

Continuity 

Connector

Terminal

Connector

Terminal

B247

22

D127

2

Existed

Sliding door control unit RH

Ground

Continuity 

Connector

Terminal

B247

22

Not existed

SLIDING DOOR HANDLE SWITCH

DLK-329

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

3.

Check continuity between sliding door control unit RH harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK SLIDING DOOR HANDLE SWITCH CIRCUIT 2

1.

Connect sliding door control unit RH connector and remote control assembly RH connector.

2.

Check voltage between sliding door control unit RH harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace sliding door control unit RH. Refer to 

DLK-500, "RH : Removal and Installation"

.

5.

CHECK SLIDING DOOR HANDLE SWITCH

Refer to 

DLK-329, "SLIDING DOOR RH : Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Replace remote control assembly RH.

6.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-42, "Intermittent Incident"

.

>> INSPECTION END

SLIDING DOOR RH : Component Inspection

INFOID:0000000009649267

1.

CHECK SLIDING DOOR HANDLE SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect remote control assembly RH connector.

3.

Check continuity between remote control assembly RH terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace remote control assembly RH.

Sliding door control unit RH

Remote control assembly RH

Continuity 

Connector

Terminal

Connector

Terminal

B247

23

D127

1

Existed

Sliding door control unit RH

Ground

Continuity 

Connector

Terminal

B247

23

Not existed

(+)

(–)

Voltage

Sliding door control unit RH

Connector

Terminal

B247

23

Ground

0 V

Remote control assembly RH

Condition

Continuity

Terminal

2

1

Sliding door handle RH

Pull

Existed

Release

Not existed

 

 

 

 

 

 

 

Content   ..  401  402  403  404   ..