Content .. 345 346 347 348 ..

Nissan Quest E52. Manual - part 347

DLK-102

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (SLIDING DOOR CONTROL UNIT LH)

ACTIVE TEST

SELF-DIAG REULT

Refer to

DLK-115, "LH : DTC Index"

KEYLESS SIG

[REV

→

MOVE

→

OFF] status of auto open/close operation is displayed according to Intel-

ligent Key button operation
• REV: When Intelligent Key signal is received (button short press)
• MOVE: When Intelligent Key signal is received (button long press)
• OFF: When Intelligent Key button is not operated

IGN SW

[ON position (ON)/other than ON position (OFF)] of ignition switch, which is judged from
ignition switch ON signal, is displayed

ENCODER A LH

Encoder status, which is judged from encoder pulse signal, is displayed

ENCODER B LH

Encoder status, which is judged from encoder pulse signal, is displayed

CHILD LOCK SW

[Lock (OFF)/unlock (ON)] status of child lock, which is judged from child lock status signal,
is displayed

FULL LATC SW L

[Full close (OFF)/other than full close (ON)] status of sliding door LH, which is judged from
full latch switch signal, is displayed

NEUTRAL SW

[Neutral position (OFF)/other than neutral position (ON)] status of sliding door closure mo-
tor, which is judged from neutral switch signal, is displayed

Monitor item

Description

Test Item

Description

CLUTCH

Clutch operation of sliding door LH can be checked according to screen operation of CONSULT
• HOLD: Clutch ON (sliding door LH cannot be operated manually)
• RELEASE: Clutch OFF (sliding door LH can be operated manually)
NOTE:
Be careful to perform active test after turning automatic door main switch to the OFF position and
setting sliding door to the halfway stop position

DIAGNOSIS SYSTEM (SLIDING DOOR CONTROL UNIT RH)

DLK-103

< SYSTEM DESCRIPTION >

DLK

DIAGNOSIS SYSTEM (SLIDING DOOR CONTROL UNIT RH)

CONSULT Function

INFOID:0000000009649017

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with sliding door control unit RH.

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

Diagnosis mode

Function description

Self Diagnostic Result

Displays the diagnosis results judged by sliding door control unit RH

CAN Diag Support Monitor

Monitors the reception status of CAN communication viewed from sliding door control
unit RH

Data Monitor

The sliding door control unit RH input/output signals are displayed

Active Test

The signal used to activate each device are forcibly supplied from sliding door control
unit RH

Ecu Identification

The sliding door control unit RH part number is displayed

Monitor item

Description

SPEED METER

Vehicle speed signal from combination meter is displayed

ABS SPEED

Vehicle speed signal from ABS actuator and electric unit (control unit) is displayed

MAIN SW

[ON/OFF] status of automatic door main switch, which is judged from automatic door main
switch signal, is displayed

KNOB LCK SW R

[Lock (OFF)/unlock (ON)] status of sliding door RH, which is judged from sliding door lock/
unlock status signal, is displayed

ONE-TOUCH SW

[Operation (ON)/non-operation (OFF)] status of sliding door one-touch open/close switch
RH, which is judged from sliding door one-touch open/close switch signal, is displayed

F LID SW

[ON/OFF] status of fuel filler lid status switch, which is judged from fuel filler lid open/close
status signal, is displayed

B PILLER SW

[Operation (ON)/non-operation (OFF)] status of sliding door open/close switch (rear RH),
which is judged from sliding door open/close switch (rear RH) signal, is displayed

DRIVER SW

[Operation (ON)/non-operation (OFF)] status of sliding door open/close switch (front RH),
which is judged from sliding door open/close switch (front RH) signal, is displayed

ACC On SW

[ON, ACC status (ON)/other than ON, ACC (OFF)] status of ignition switch, which is
judged from ACC signal, is displayed

DOR HAND SW R

[Operation (ON)/non-operation (OFF)] status of sliding door handle RH, which is judged
from sliding door handle switch signal, is displayed

TOUCH SEN RH

[Pinching detection (ON)/non-detection (OFF)] status of sliding door touch sensor RH,
which is judged from sliding door touch sensor signal, is displayed

RR-RH DOOR SW

[Open (ON)/close (OFF)] status of sliding door RH, which is judged from sliding door
switch signal, is displayed

HAF LATC SW R

[Half latch, fully close (OFF)/open (ON)] status of half latch switch, which is judged from
half latch switch signal, is displayed

P RANGE SW

[P position (ON)/other than P position (OFF)] status of selector lever, which is judged from
shift position signal, is displayed

BRAKE SW

[Depressed (ON)/non-depressed (OFF)] status of brake pedal, which is judged from stop
lamp switch signal, is displayed

P BRAKE SW

[Operation (ON)/non-operation (OFF)] status of parking brake, which is judged from park
brake switch signal, is displayed

DLK-104

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (SLIDING DOOR CONTROL UNIT RH)

ACTIVE TEST

SELF-DIAG REULT

Refer to

DLK-121, "RH : DTC Index"

KEYLESS SIG

[REV

→

MOVE

→

OFF] status of auto open/close operation is displayed according to Intel-

IGN SW

[ON position (ON)/other than ON position (OFF)] of ignition switch, which is judged from
ignition switch ON signal, is displayed

ENCODER A RH

Encoder status, which is judged from encoder pulse signal, is displayed

ENCODER B RH

Encoder status, which is judged from encoder pulse signal, is displayed

CHILD LOCK SW

[Lock (OFF)/unlock (ON)] status of child lock, which is judged from child lock status signal,
is displayed

FUL LATC SW R

[Full close (OFF)/other than full close (ON)] status of sliding door RH, which is judged from
full latch switch signal, is displayed

NEUTRAL SW

[Neutral position (OFF)/other than neutral position (ON)] status of sliding door closure mo-
tor, which is judged from neutral switch signal, is displayed

Monitor item

Description

Test Item

Description

CLUTCH

Clutch operation of sliding door RH can be checked according to screen operation of CONSULT
• HOLD: Clutch ON (sliding door RH cannot be operated manually)
• RELEASE: Clutch OFF (sliding door RH can be operated manually)
NOTE:
Be careful to perform active test after turning automatic door main switch to the OFF position and
setting sliding door to the halfway stop position

BCM

DLK-105

< ECU DIAGNOSIS INFORMATION >

DLK

ECU DIAGNOSIS INFORMATION

BCM

List of ECU Reference

INFOID:0000000009649018

ECU

Reference

BCM

BCS-40, "Reference Value"

BCS-62, "Fail-safe"

BCS-62, "DTC Inspection Priority Chart"

BCS-63, "DTC Index"

Content .. 345 346 347 348 ..