Nissan Quest E52. Manual - part 14

MEMORY STORING

ADP-49

< BASIC INSPECTION >

ADP

MEMORY STORING

Description

INFOID:0000000009649621

Always perform the memory storage when the battery terminal is disconnected or the driver seat control unit is
replaced. The memory function will not operate normally if no memory storage is performed.

Work Procedure

INFOID:0000000009649622

Two positions for the driver seat and outside mirror can be stored for memory operation by following proce-
dure.
NOTE:
If memory is stored in the same memory switch, the previous memory will be deleted.

STEP 1

Check the following conditions.
• Ignition switch: ON
• CVT shift selector: P position

>> GO TO 2.

STEP 2

Adjust driver seat and outside mirror position manually.

Push set switch.
NOTE:
• Memory indicator for which driver seat position is already retained in memory is illuminated for 5 sec-

onds.

• Memory indicator for which driver seat position is not retained in memory is illuminated for 0.5 second.

Push the memory switch (1 or 2) for at least 1 second within 5 seconds after pushing the set switch.
NOTE:
• To enter driver seat positions into blank memory, memory indicator will be turned on for 5 seconds.
• To modify driver seat positions, memory indicator will be turned OFF for 0.5 second, then turned ON for

5 seconds.

Confirm the operation of each part with memory operation.

>> END

ADP-50

< BASIC INSPECTION >

INTELLIGENT KEY INTERLOCK STORING

INTELLIGENT KEY INTERLOCK STORING

Description

INFOID:0000000009649623

Always perform the Intelligent Key interlock function storage when the battery terminal is disconnected or the
driver seat control unit is replaced. The Intelligent Key interlock function will not operate normally if no memory
storage is performed.

Work Procedure

INFOID:0000000009649624

Performing the following operation associates the registered driving position with Intelligent Key. When driver
door unlock operation is performed by Intelligent Key or driver door request switch, display of the registered
driving position and turnout operation can be performed.

STEP 1

Check the following conditions.
• Ignition switch: OFF
• Initialization: done
• Driving position: registered

>> GO TO 2.

STEP 2

Push set switch.
NOTE:
Memory indicator for which driver seat position is already retained in memory is illuminated for 5 seconds.

Push the Intelligent Key unlock button within 5 seconds after pushing memory switch (while the memory
indicator is turned ON).
NOTE:
From the time registration is performed, the applicable memory indicator blinks for 5 seconds.

Confirm the operation of each part with memory operation and Intelligent Key interlock operation.

>> END

SYSTEM SETTING

ADP-51

< BASIC INSPECTION >

ADP

SYSTEM SETTING

Description

INFOID:0000000009649625

The settings of the automatic driving positioner system can be changed, using CONSULT and the set switch.
Always check the settings before and after disconnecting the battery terminal or replacing driver seat control
unit.

SETTING CHANGE

: Applicable

Work Procedure

INFOID:0000000009649626

STEP 1

There are three way of setting method.

Which method do you choose?

With CONSULT>>GO TO 2.
With set switch>>GO TO 3.

STEP 2-A (WITH CONSULT)

Select “Work support”.

Select “EXIT SEAT SLIDE SETTING” then touch display to change between ON and OFF.

EXIT SEAT SLIDE SETTING: Entry/exit assist (seat)

Select “SEAT SLIDE VOLUME SET” and touch either of “40 mm”, “80 mm”, or “150 mm”.

Then touch “OK”.

>> END

STEP 2-B (WITH SET SWITCH)

Turn ignition switch OFF.

Push set switch and hold for more than 10 seconds, then confirm blinking of the memory switch indicator.

Entry/exit assist are ON: Memory switch indicator blink two times.

Entry/exit assist are OFF: Memory switch indicator blink once.

>> END

Item

Content

CONSULT

Set

switch

Factory

setting

Amount of seat sliding for
entry/exit assist

The amount of seat sliding for entry/exit assist can be
selected from 3 items.
[40 mm/80 mm/150 mm]

—

40 mm

Entry/exit assist
(seat)

Entry/exit assist (seat) can be selected:
ON (operated) – OFF (not operated)

ADP-52

< DTC/CIRCUIT DIAGNOSIS >

U1000 CAN COMM CIRCUIT

DTC/CIRCUIT DIAGNOSIS

U1000 CAN COMM CIRCUIT

Description

INFOID:0000000009649627

CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Modern
vehicle is equipped with many electronic control unit, and each control unit shares information and links with
other control units during operation (not independent). In CAN communication, control units are connected
with 2 communication lines (CAN H-line, CAN L-line) allowing a high rate of information transmission with less
wiring. Each control unit transmits/receives data but selectively reads required data only.

DTC Logic

INFOID:0000000009649628

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

STEP 1

Turn ignition switch ON and wait at least 3 seconds.

>> GO TO 2.

STEP 2

Check “Self diagnostic result” with CONSULT.

Is the DTC detected?

YES

>> Refer to