Nissan Quest E52. Manual - part 13

DIAGNOSIS AND REPAIR WORK FLOW

ADP-45

< BASIC INSPECTION >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

YES

>> INSPECTION END

Symptom is detected.>> GO TO 5.
DTC is detected.>> GO TO 6.

ADP-46

< BASIC INSPECTION >

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMI-
NAL

Description

INFOID:0000000009649615

Each function is reset to the following condition when the battery terminal is disconnected.

*

: Default value is 40 mm.

NOTE:
Notice that disconnecting the battery when detected DTC are present will erase the DTC memory.

Work Procedure

INFOID:0000000009649616

1.

SYSTEM INITIALIZATION

Perform system initialization. Refer to 

ADP-48, "Work Procedure"

.

>> GO TO 2.

2.

MEMORY STORAGE

Perform memory storage. Refer to 

ADP-49, "Work Procedure"

.

>> GO TO 3.

3.

INTELLIGENT KEY INTERLOCK STORAGE

Perform Intelligent Key interlock storage. Refer to 

ADP-50, "Work Procedure"

.

>> GO TO 4.

4.

SYSTEM SETTING

Perform system setting. Refer to 

ADP-51, "Work Procedure"

.

>> END

Function

Condition

Procedure

Memory (Seat, mirror)

Erased

Perform storing

Entry/exit assist

ON

Perform initialization

Set slide amount

*

Intelligent Key interlock

Erased

Perform initialization

Perform storing

ADDITIONAL SERVICE WHEN REMOVING DRIVER SEAT CONTROL UNIT

ADP-47

< BASIC INSPECTION >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

ADDITIONAL SERVICE WHEN REMOVING DRIVER SEAT CONTROL
UNIT

Description

INFOID:0000000009649617

Each function is reset to the following condition when the driver seat control unit is replaced.

*

: Default value is 40 mm.

NOTE:
Notice that disconnecting the battery when detected DTC are present will erase the DTC memory.

Work Procedure

INFOID:0000000009649618

1.

SYSTEM INITIALIZATION

Perform system initialization. Refer to 

ADP-48, "Work Procedure"

.

>> GO TO 2.

2.

MEMORY STORAGE

Perform memory storage. Refer to 

ADP-49, "Work Procedure"

.

>> GO TO 3.

3.

INTELLIGENT KEY INTERLOCK STORAGE

Perform Intelligent Key interlock storage. Refer to 

ADP-50, "Work Procedure"

.

>> GO TO 4.

4.

SYSTEM SETTING

Perform system setting. Refer to 

ADP-51, "Work Procedure"

.

>> END

Function

Condition

Procedure

Memory (Seat, mirror)

Erased

Perform storing

Entry/exit assist

ON

Perform initialization

Set slide amount

*

Intelligent Key interlock

Erased

Perform initialization

Perform storing

ADP-48

< BASIC INSPECTION >

SYSTEM INITIALIZATION

SYSTEM INITIALIZATION

Description

INFOID:0000000009649619

Always perform the initialization when the battery terminal is disconnected or the driver seat control unit is
replaced.
The entry/exit assist function will not operate normally if no initialization is performed. 

Work Procedure

INFOID:0000000009649620

1.

STEP 1

There are two initialization methods.

Which method do you use?

With door switch>>GO TO 2.
With vehicle speed>>GO TO 3.

2.

 STEP 2-A (WITH DOOR SWITCH)

1.

Turn ignition switch from ACC to OFF position. 

2.

Front door switch (driver side) is ON (open) 

→

 OFF (close) 

→

 ON (open).

>> END

3.

 STEP 2-B (WITH VEHICLE SPEED)

Drive the vehicle at more than 25 km/h (16 MPH). 

>> END