Nissan Cube. Manual - part 963

TM-108

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F08B]

P0703 BRAKE SWITCH B

YES

>> INSPECTION END

NO

>> Replace stop lamp switch. Refer to 

BR-17, "Exploded View"

.

7.

DETECT MALFUNCTIONING ITEMS

Check the following.
• 10A fuse (No.9)
• Harness for short or open between battery and stop lamp switch (Refer to 

PG-6, "Wiring Diagram - BAT-

TERY POWER SUPPLY -"

.)

• Battery
Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Repair or replace damaged parts.

8.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-40, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-88, "Exploded View"

 (With intelligent key system), 

BCS-155,

"Exploded View"

 (Without intelligent key system).

NO

>> Repair or replace damaged parts.

Component Inspection (Stop Lamp Switch)

INFOID:0000000009948955

1.

CHECK STOP LAMP SWITCH

Check continuity between stop lamp switch connector terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace stop lamp switch. Refer to 

BR-17, "Exploded View"

.

Stop lamp switch connector

Condition

Continuity

Connector

Terminal

E115

1

2

Depressed brake pedal

Existed

Brake pedal not depressed

Not existed

3

4

Depressed brake pedal

Existed

Brake pedal not depressed

Not existed

P0705 TRANSMISSION RANGE SWITCH A

TM-109

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F08B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P0705 TRANSMISSION RANGE SWITCH A

Description

INFOID:0000000009948956

• Transmission range switch is installed to upper part of transaxle case.
• Transmission range switch detects the selector lever position and transmits selector lever position signal to

TCM.

DTC Logic

INFOID:0000000009948957

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

Immediately after performing any “DTC CONFIRMATION PROCEDURE”, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1.

Start the engine.

2.

Shift and hold selector lever to each position for 5 seconds or more.

3.

Select “Self Diagnostic Results” in “TRANSMISSION”.

With GST

Follow the procedure “With CONSULT”.

Is “P0705” detected?

YES

>> Go to 

TM-109, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009948958

1.

 CHECK TRANSMISSION RANGE SWITCH POWER CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect transmission range switch connector.

3.

Turn ignition switch ON.

4.

Check voltage between transmission range switch vehicle side harness connector terminal and ground.

Is the inspection result normal?

YES 

>> GO TO 2.

NO

>> GO TO 5.

2.

 CHECK HARNESS BETWEEN TCM AND TRANSMISSION RANGE SWITCH (PART 1)

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector.

DTC

Trouble diagnosis name

DTC is detected if...

Possible cause

P0705

Transmission Range Sensor A 
Circuit (PRNDL Input)

• Range signal is not transmitted to TCM
• 2 or more range signals are transmitted to 

TCM

• Harness or connectors

[Transmission range switch circuit is open 
or shorted.]

• Transmission range switch

Transmission range switch vehicle side harness connector

Ground

Condition

Voltage (Approx.)

Connector

Terminal

F21

3

Ignition switch: ON

Battery voltage

Ignition switch: OFF

0 V

TM-110

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F08B]

P0705 TRANSMISSION RANGE SWITCH A

3.

Check continuity between TCM vehicle side harness connector terminals and transmission range switch
vehicle side harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace damaged parts.

3.

CHECK HARNESS BETWEEN TCM AND TRANSMISSION RANGE SWITCH (PART 2)

Check continuity between TCM vehicle side harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace damaged parts.

4.

CHECK TRANSMISSION RANGE SWITCH

1.

Remove control cable from manual lever. Refer to 

TM-219, "Exploded View"

.

2.

Check transmission range switch. Refer to 

TM-111, "Component Inspection (Transmission Range

Switch)"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

NO

>> Transmission range switch is malfunctioning. Replace transaxle assembly. Refer to 

TM-235,

"Exploded View"

.

5.

CHECK HARNESS BETWEEN TRANSMISSION RANGE SWITCH AND IPDM E/R (PART 1)

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector.

3.

Check continuity between transmission range switch vehicle side harness connector terminals and IPDM
E/R vehicle side harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace damaged parts.

6.

CHECK HARNESS BETWEEN TRANSMISSION RANGE SWITCH AND IPDM E/R (PART 2)

Check continuity between transmission range switch vehicle side harness connector terminal and ground.

TCM vehicle side harness connector

Transmission range switch vehicle side harness 

connector

Continuity

Connector

Terminal

Connector

Terminal

E18

18

F21

4

Existed

22

5

E19

26

6

43

7

44

8

TCM vehicle side harness connector

Ground

Continuity

Connector

Terminal

E18

18

Not existed

22

E19

26

43

44

Transmission range switch vehicle side harness 

connector

IPDM E/R vehicle side harness connector

Continuity

Connector

Terminal

Connector

Terminal

F21

3

E15

58

Existed

P0705 TRANSMISSION RANGE SWITCH A

TM-111

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F08B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace damaged parts.

7.

DETECT MALFUNCTIONING ITEMS

Check the following.
• IPDM E/R
• 10A fuse (No.55, located in the IPDM E/R)
• Harness for short or open between IPDM E/R and ignition switch (Refer to 

PG-33, "Wiring Diagram - IGNI-

TION POWER SUPPLY -"

.)

• Ignition switch

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

NO

>> Repair or replace damaged parts.

Component Inspection (Transmission Range Switch)

INFOID:0000000009948959

1.

CHECK TRANSMISSION RANGE SWITCH

Check continuity of transmission range switch connector terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Transmission range switch is malfunctioning. Replace transaxle assembly. Refer to 

TM-235,

"Exploded View"

.

Transmission range switch vehicle side harness connector

Ground

Continuity

Connector

Terminal

F21

3

Not existed

Transmission range switch connector

Condition

Continuity

Connector

Terminal

F21

1

2

Manual lever: “P” and “N” positions

Existed

Other than the above

Not existed

3

4

Manual lever: “P” position

Existed

Other than the above

Not existed

3

5

Manual lever: “R” position

Existed

Other than the above

Not existed

3

6

Manual lever: “N” position

Existed

Other than the above

Not existed

3

7

Manual lever: “D” position

Existed

Other than the above

Not existed

3

8

Manual lever: “L” position

Existed

Other than the above

Not existed