Nissan Cube. Manual - part 844

DIAGNOSIS SYSTEM (BCM)

SEC-187

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

ACTIVE TEST

PANIC ALARM

PANIC ALARM : CONSULT Function (BCM - PANIC ALARM)

INFOID:0000000009950251

ACTIVE TEST

Test Item

Description

SECURITY ALARM SET

This mode is able to confirm and change security alarm ON-OFF setting.

THEFT ALM TRG

The switch which triggered vehicle security alarm is recorded. This mode is able to confirm and 
erase the record of vehicle security alarm. The trigger data can be erased by touching 
“CLEAR” on CONSULT screen.

Test Item

Description

THEFT IND

This test is able to check security indicator lamp operation. Security indicator lamp will be 
turned on when “ON” on CONSULT screen is touched.

VEHICLE SECURITY HORN

This test is able to check horn operation. Horn will be activated for 0.5 seconds after “ON” on 
CONSULT screen is touched.

HEADLAMP (HI)

This test is able to check headlamp (HI) operation. Headlamps (HI) will be activated for 0.5 
seconds after “ON” on CONSULT screen is touched.

FLASHER

This test is able to check hazard warning lamp operation. Hazard warning lamps will be acti-
vated after “LH” or “RH” on CONSULT screen is touched.

Test item

Description

VEHICLE SECURITY HORN

This test is able to check horn operation. Horn is activated for 0.5 seconds after “ON” 
on CONSULT screen touched.

HEAD LAMP (HI)

This test is able to check headlamp (HI) operation. Headlamps (HI) will be activated af-
ter “ON” on CONSULT screen touched.

SEC-188

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (IPDM E/R)

DIAGNOSIS SYSTEM (IPDM E/R)

CONSULT Function (IPDM E/R)

INFOID:0000000010251892

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with IPDM E/R.

SELF DIAGNOSTIC RESULT

Refer to 

PCS-62, "DTC Index"

.

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

Diagnosis mode

Description

Ecu Identification

Allows confirmation of IPDM E/R part number.

Self Diagnostic Result

Displays the diagnosis results judged by IPDM E/R.

Data Monitor

Displays the real-time input/output data from IPDM E/R input/output data.

Active Test

IPDM E/R can provide a drive signal to electronic components to check their operations.

CAN Diag Support Monitor

The results of transmit/receive diagnosis of CAN communication can be read.

Monitor Item

[Unit]

MAIN SIG-

NALS

Description

MOTOR FAN REQ
[1/2/3/4]

×

Displays the value of the cooling fan speed request signal received from ECM via 
CAN communication.

AC COMP REQ
[Off/On]

×

Displays the status of the A/C compressor request signal received from ECM via 
CAN communication.

TAIL&CLR REQ
[Off/On]

×

Displays the status of the position light request signal received from BCM via CAN 
communication.

HL LO REQ
[Off/On]

×

Displays the status of the low beam request signal received from BCM via CAN 
communication.

HL HI REQ
[Off/On]

×

Displays the status of the high beam request signal received from BCM via CAN 
communication.

FR FOG REQ
[Off/On]

×

Displays the status of the front fog light request signal received from BCM via 
CAN communication.

FR WIP REQ
[Stop/1LOW/Low/Hi]

×

Displays the status of the front wiper request signal received from BCM via CAN 
communication.

WIP AUTO STOP
[STOP P/ACT P]

×

Displays the status of the front wiper auto stop signal judged by IPDM E/R.

WIP PROT
[Off/BLOCK]

×

Displays the status of the front wiper fail-safe operation judged by IPDM E/R.

IGN RLY
[Off/On]

×

Displays the status of the ignition relay judged by IPDM E/R.

INTER/NP SW
[Off/On]

Displays the status of the shift position (CVT models) judged by IPDM E/R.

ST RLY-REQ
[Off/On]

Displays the status of the starter relay status signal received from BCM via CAN 
communication.

DTRL REQ
[Off/On]

NOTE:
The item is indicated, but not monitored.

OIL P SW
[Open/Close]

Displays the status of the oil pressure switch judged by IPDM E/R.

HOOD SW
[Off/On]

NOTE:
The item is indicated, but not monitored.

DIAGNOSIS SYSTEM (IPDM E/R)

SEC-189

< SYSTEM DESCRIPTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

ACTIVE TEST

THFT HRN REQ
[Off/On]

Displays the status of the theft warning horn request signal received from BCM 
via CAN communication.

HORN CHIRP
[Off/On]

Displays the status of the horn reminder signal received from BCM via CAN com-
munication.

Monitor Item

[Unit]

MAIN SIG-

NALS

Description

Test item

Operation

Description

HORN

On

Operates horn relay for 20 ms.

FRONT WIPER

Off

OFF

Lo

Operates the front wiper relay.

Hi

Operates the front wiper relay and front wiper high relay.

MOTOR FAN

1

OFF

2

Operates the cooling fan relay (LO operation).

3

Operates the cooling fan relay (HI operation).

4

EXTERNAL LAMPS

Off

OFF

TAIL

Operates the tail lamp relay.

Lo

Operates the headlamp low relay.

Hi

Operates the headlamp low relay and ON/OFF the headlamp high relay at 1 sec-
ond intervals.

Fog

Operates the front fog lamp relay.

SEC-190

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

P1610 LOCK MODE

DTC/CIRCUIT DIAGNOSIS

P1610 LOCK MODE

Description

INFOID:0000000009950253

ECM forcibly switches to the mode that inhibits engine start, when engine start operation is performed 5 times
or more while communication between ECM and BCM is not normal, and when engine start operation is per-
formed 5 times or more by unregistered ignition key.

DTC Logic

INFOID:0000000009950254

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON.

2.

Check “Self diagnosis result” with CONSULT.

Is DTC detected?

YES

>> Refer to 

SEC-190, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009950255

1.

CHECK ENGINE START FUNCTION

1.

Perform the check for DTC except DTC P1610.

2.

Use CONSULT to erase DTC after fixing.

3.

Turn ignition switch OFF.

4.

Turn ignition switch ON when registered ignition key is inserted into key cylinder and wait for 5 seconds.

5.

Turn the ignition switch OFF and wait 5 seconds.

6.

Repeat steps 4 and 5 twice (a total of 3 times).

7.

Check that engine can start when registered ignition key is inserted into key cylinder.

>> INSPECTION END

DTC No.

Trouble diagnosis 

name

DTC detecting condition

Possible cause

P1610

LOCK MODE

When ECM detects any of the following 2 states
• Ignition switch ON 5 times or more during communication between 

ECM and BCM is malfunctioning

• Ignition switch ON by unregistered ignition key 5 times or more

—