Nissan Cube. Manual - part 438

EXL-26

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)

*: Factory setting

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

Service item

Setting 

item

Setting

BATTERY SAVER SET

On*

With the exterior lamp battery saver function

Off

Without the exterior lamp battery saver function

ILL DELAY SET

MODE 1

NOTE:
This item is displayed, but cannot be used

MODE 2

MODE 3

MODE 4

MODE 5

MODE 6

MODE 7

MODE 8

AUTO LIGHT LOGIC SET

MODE 1

NOTE:
This item is displayed, but cannot be used

MODE 2

MODE 3

MODE 4

MODE 5

MODE 6

Monitor item

[Unit]

Description

IGN ON SW
[On/Off]

Indicated [On/Off] condition of ignition switch in ON position

ACC ON SW
[On/Off]

Indicates [On/Off] condition of ignition switch in ACC position

HI BEAM SW
[On/Off]

Each switch status that BCM judges from the combination switch reading function

HEAD LAMP SW 1
[On/Off]

HEAD LAMP SW 2
[On/Off]

TAIL LAMP SW
[On/Off]

AUTO LIGHT SW*
[On/Off]

PASSING SW
[On/Off]

FR FOG SW*
[On/Off]

DOOR SW-DR
[On/Off]

Indicated [On/Off] condition of front door switch (driver side)

DOOR SW-AS
[On/Off]

Indicated [On/Off] condition of front door switch (passenger side)

DOOR SW-RR
[On/Off]

Indicated [On/Off] condition of rear door switch RH

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)

EXL-27

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

*: This item is displayed, but cannot be monitored.

ACTIVE TEST

FLASHER

FLASHER : CONSULT Function (BCM - FLASHER)

INFOID:0000000009945131

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

DOOR SW- RL
[On/Off]

Indicated [On/Off] condition of rear door switch LH

BACK DOOR SW
[On/Off]

Indicated [On/Off] condition of back door switch

TURN SIGNAL R
[On/Off]

Each switch status that BCM judges from the combination switch reading function

TURN SIGNAL L
[On/Off]

KEY ON SW
[On/Off]

Indicated [On/Off] condition of key switch

KEYLESS LOCK
[On/Off]

Indicated [On/Off] condition of lock signal from key fob

PKB SW
[On/Off]

The parking brake switch status received from combination meter with CAN communica-
tion

ENGINE RUN
[On/Off]

The engine status received from ECM with CAN communication

VEHICLE SPEED
[km/h]

Display the vehicle speed signal received from combination meter by numerical value 
[Km/h]

OPTI SEN (DTCT)
[V]

NOTE:
This item is displayed, but cannot be monitored

OPTI SEN (FILT)
[V]

NOTE:
This item is displayed, but cannot be monitored

Monitor item

[Unit]

Description

Test item

Operation

Description

TAIL LAMP

On

Transmits the position light request signal to IPDM E/R with CAN commu-
nication to turn the tail lamp ON.

Off

Stops the tail lamp request signal transmission.

HEAD LAMP

Hi

Transmits the high beam request signal with CAN communication to turn 
the headlamp (HI).

Lo

Transmits the low beam request signal with CAN communication to turn the 
headlamp (LO).

Off

Stops the high & low beam request signal transmission.

FR FOG LAMP

On

NOTE:
This item is displayed, but cannot be tested

Off

ILL DIM SIGNAL

On

NOTE:
This item is displayed, but cannot be tested

Off

EXL-28

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)

ACTIVE TEST

Monitor item

[Unit]

Description

IGN ON SW
[On/Off]

Indicated [On/Off] condition of ignition switch in ON position

HAZARD SW
[On/Off]

The switch status input from the hazard switch

TURN SIGNAL R
[On/Off]

Each switch status that BCM detects from the combination switch reading function

TURN SIGNAL L
[On/Off]

Test item

Operation

Description

FLASHER

RH

Outputs the voltage to turn the right side turn signal lamps ON.

LH

Outputs the voltage to turn the left side turn signal lamps ON.

Off

Stops the voltage to turn the turn signal lamps OFF.

DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)

EXL-29

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)

Diagnosis Description

INFOID:0000000010249363

AUTO ACTIVE TEST

Description

In auto active test mode, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Oil pressure warning lamp
• Rear window defogger
• Front wiper (LO, HI)
• Parking lamps
• Side marker lamp
• License plate lamps
• Tail lamps
• Front fog lamps
• Headlamps (LO, HI)
• A/C compressor (magnet clutch)
• Cooling fan

Operation Procedure

1.

Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper
operation)
NOTE:
When auto active test is performed with hood opened, sprinkle water on windshield beforehand.

2.

Turn the ignition switch OFF.

3.

Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the
ignition switch OFF.

CAUTION:

Close passenger door.

4.

Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts.

5.

The oil pressure warning lamp starts blinking when the auto active test starts.

6.

After a series of the following operations is repeated 3 times, auto active test is completed.

NOTE:
When auto active test mode has to be cancelled halfway through test, turn the ignition switch OFF.

CAUTION:

• If auto active test mode cannot be actuated, check door switch system. Refer to 

DLK-55,

"Component Function Check"

.

• Do not start the engine.

Inspection in Auto Active Test Mode

When auto active test mode is actuated, the following 6 steps are repeated 3 times.

Operation 
sequence

Inspection location

Operation

A

Oil pressure warning lamp

Blinks continuously during operation of auto active test 

1

Rear window defogger

10 seconds

2

Front wiper

LO for 5 seconds 

→

 HI for 5 seconds

3

• Parking  lamps
• Side marker lamps
• License plate lamps
• Tail lamps
• Front fog lamps

10 seconds

4

Headlamps

LO for 10 seconds 

→

HI ON 

⇔

 OFF 5 times

5

A/C compressor (magnet clutch)

ON 

⇔

 OFF 5 times

6

Cooling fan

LO for 5 seconds 

→

 HI for 5 seconds