Nissan Cube. Manual - part 112

BRC-98

< ECU DIAGNOSIS INFORMATION >

[VDC/TCS/ABS]

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

DTC Index

INFOID:0000000009950029

DTC

Items (CONSULT screen terms)

Reference

C1101

RR RH SENSOR-1

BRC-28, "DTC Logic"

C1102

RR LH SENSOR-1

C1103

FR RH SENSOR-1

C1104

FR LH SENSOR-1

C1105

RR RH SENSOR-2

BRC-31, "DTC Logic"

C1106

RR LH SENSOR-2

C1107

FR RH SENSOR-2

C1108

FR LH SENSOR-2

C1109

BATTERY VOLTAGE [ABNORMAL]

BRC-36, "DTC Logic"

C1110

CONTROLLER FAILURE

BRC-38, "DTC Logic"

C1111

PUMP MOTOR

BRC-39, "DTC Logic"

C1115

ABS SENSOR [ABNORMAL SIGNAL]

BRC-41, "DTC Logic"

C1116

STOP LAMP SW

BRC-46, "DTC Logic"

C1120

FR LH IN ABS SOL

BRC-51, "DTC Logic"

C1121

FR LH OUT ABS SOL

BRC-53, "DTC Logic"

C1122

FR RH IN ABS SOL

BRC-51, "DTC Logic"

C1123

FR RH OUT ABS SOL

BRC-53, "DTC Logic"

C1124

RR LH IN ABS SOL

BRC-51, "DTC Logic"

C1125

RR LH OUT ABS SOL

BRC-53, "DTC Logic"

C1126

RR RH IN ABS SOL

BRC-51, "DTC Logic"

C1127

RR RH OUT ABS SOL

BRC-53, "DTC Logic"

C1130

ENGINE SIGNAL 1

BRC-55, "DTC Logic"

C1140

ACTUATOR RLY

BRC-57, "DTC Logic"

C1142

PRESS SEN CIRCUIT

BRC-59, "DTC Logic"

C1143

ST ANG SEN CIRCUIT

BRC-61, "DTC Logic"

C1144

ST ANG SEN SIGNAL

BRC-63, "DTC Logic"

C1145

YAW RATE SENSOR

BRC-64, "DTC Logic"

C1146

SIDE G-SEN CIRCUIT

C1153

EMERGENCY BRAKE

BRC-38, "DTC Logic"

C1155

BR FLUID LEVEL LOW

BRC-67, "DTC Logic"

C1164

CV 1

BRC-70, "DTC Logic"

C1165

CV 2

C1166

SV 1

BRC-72, "DTC Logic"

C1167

SV 2

C1170

VARIANT CORDING

BRC-38, "DTC Logic"

U1000

CAN COMM CIRCUIT

BRC-74, "DTC Logic"

U1002

SYSTEM COMM

BRC-75, "DTC Logic"

EXCESSIVE ABS FUNCTION OPERATION FREQUENCY

BRC-99

< SYMPTOM DIAGNOSIS >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

SYMPTOM DIAGNOSIS

EXCESSIVE ABS FUNCTION OPERATION FREQUENCY

Diagnosis Procedure

INFOID:0000000009950030

1.

CHECK START

Check front and rear brake force distribution using a brake tester. Refer to 

BR-43, "General Specifications"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check brake system.

2.

CHECK FRONT AND REAR AXLE

Make sure that there is no excessive play in the front and rear axles.
• Front: refer to 

FAX-7, "Inspection"

.

• Rear: refer to 

RAX-5, "Inspection"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace error-detected parts.

3.

CHECK WHEEL SENSOR AND SENSOR ROTOR

Check the following.
• Wheel sensor installation for damage.
• Wheel sensor harness connector connection.
• Wheel sensor harness inspection.
• Sensor rotor installation for damage. 

Is the inspection result normal?

YES

>> GO TO 4.

NO

>>

Replace wheel sensor or sensor rotor.

• Front wheel sensor: refer to 

BRC-110, "FRONT WHEEL SENSOR : Exploded View"

.

• Rear wheel sensor: refer to 

BRC-111, "REAR WHEEL SENSOR : Exploded View"

.

• Front sensor rotor: refer to 

BRC-112, "FRONT SENSOR ROTOR : Removal and Installation"

.

• Rear sensor rotor: refer to 

BRC-112, "REAR SENSOR ROTOR : Removal and Installation"

.

4.

CHECK ABS WARNING LAMP DISPLAY

Make sure that the ABS warning lamp is turned OFF for approximately 1 second after the ignition switch is
turned ON or when driving. 

Is the inspection result normal?

YES

>> Normal

NO

>> Perform self-diagnosis for “ABS” with CONSULT.

BRC-100

< SYMPTOM DIAGNOSIS >

[VDC/TCS/ABS]

UNEXPECTED PEDAL REACTION

UNEXPECTED PEDAL REACTION

Diagnosis Procedure

INFOID:0000000009950031

1.

CHECK BRAKE PEDAL STROKE

Check brake pedal stroke. Refer to 

BR-7, "Inspection and Adjustment"

.

Is the stroke too large?

YES

>> • Bleed air from brake tube and hose. Refer to 

BR-11, "Bleeding Brake System"

.

• Check brake fluid leakage. Refer to 

BR-10, "Inspection"

.

• Check brake pedal, brake booster, and master cylinder for mount play, looseness, etc.
- Brake pedal: refer to 

BR-18, "Inspection and Adjustment"

.

- Brake master cylinder: refer to 

BR-27, "Inspection"

.

- Brake booster: refer to 

BR-29, "Inspection and Adjustment"

.

- Front disc brake: refer to 

BR-38, "BRAKE CALIPER ASSEMBLY : Inspection"

.

- Rear drum brake: refer to 

BR-41, "Inspection and Adjustment"

.

NO

>> GO TO 2.

2.

CHECK FUNCTION

1.

Turn the ignition switch OFF.

2.

Disconnect ABS actuator and electric unit (control unit) harness connector to deactivate ABS. Check if
braking force is normal in this condition. Connect harness connector after inspection.

Is the inspection result normal?

YES

>> Normal

NO

>> Check brake system.

THE BRAKING DISTANCE IS LONG

BRC-101

< SYMPTOM DIAGNOSIS >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

THE BRAKING DISTANCE IS LONG

Diagnosis Procedure

INFOID:0000000009950032

CAUTION:

The stopping distance on slippery road surfaces might be longer when the ABS is operating than
when the ABS is not operating.

1.

CHECK FUNCTION

1.

Turn the ignition switch OFF

2.

Disconnect ABS actuator and electric unit (control unit) harness connector to deactivate ABS. In this con-
dition, check stopping distance. After inspection, connect harness connector.

Is the inspection result normal?

YES

>> Normal

NO

>> Check brake system.