Nissan Cube. Manual - part 108

BRC-82

< DTC/CIRCUIT DIAGNOSIS >

[VDC/TCS/ABS]

VDC OFF SWITCH

Component Inspection

INFOID:0000000009950007

1.

CHECK VDC OFF SWITCH

1.

Turn the ignition switch OFF.

2.

Disconnect VDC OFF switch harness connector.

3.

Check the continuity between VDC OFF switch harness connector.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace VDC OFF switch. Refer to 

BRC-117, "Removal and Installation"

.

Special Repair Requirement

INFOID:0000000009950008

1.

ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION

Always perform the neutral position adjustment for the steering angle sensor, when replacing the ABS actua-
tor and electric unit (control unit) or steering angle sensor and removing steering angle sensor. Refer to 

BRC-

9, "Special Repair Requirement"

>> END

VDC OFF switch

Condition

Continuity

Terminal

1 

−

 2

When VDC OFF switch is hold pressed.

Existed

When releasing VDC OFF switch.

Not existed

ABS WARNING LAMP

BRC-83

< DTC/CIRCUIT DIAGNOSIS >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

ABS WARNING LAMP

Description

INFOID:0000000009950009

×

: ON –: OFF

Component Function Check

INFOID:0000000009950010

1.

CHECK ABS WARNING LAMP OPERATION

Check that the lamp illuminates for approximately 1 second after the ignition switch is turned ON.

CAUTION:

Never start the engine.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Proceed to diagnosis procedure. Refer to 

BRC-83, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009950011

1.

PERFORM SELF-DIAGNOSIS

Perform self-diagnosis for “ABS” with CONSULT.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check item displayed by self-diagnosis.

2.

CHECK COMBINATION METER

Check if the indication and operation of combination meter are normal. Refer to 

MWI-29, "Diagnosis Descrip-

tion"

.

Is the inspection result normal?

YES

>> Replace ABS actuator and electric unit (control unit). Refer to 

BRC-113, "Exploded View"

.

NO

>> Repair or replace error-detected parts.

Special Repair Requirement

INFOID:0000000009950012

1.

ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION

Always perform the neutral position adjustment for the steering angle sensor, when replacing the ABS actua-
tor and electric unit (control unit) or steering angle sensor and removing steering angle sensor. Refer to 

BRC-

9, "Special Repair Requirement"

>> END

Condition

ABS warning lamp

Ignition switch OFF

–

For 1 second after turning ignition switch ON

×

1 second later after turning ignition switch ON

–

ABS function is malfunctioning.

×

EBD function is malfunctioning.

×

BRC-84

< DTC/CIRCUIT DIAGNOSIS >

[VDC/TCS/ABS]

BRAKE WARNING LAMP

BRAKE WARNING LAMP

Description

INFOID:0000000009950013

×

: ON –: OFF

NOTE:

• 1: Brake warning lamp will turn ON in case of parking brake operation (when switch is ON) or of brake fluid level switch operation

(when brake fluid is insufficient).

• 2: After starting the engine, brake warning lamp is turned off.

Component Function Check

INFOID:0000000009950014

1.

BRAKE WARNING LAMP OPERATION CHECK 1

Check that the lamp illuminates for approximately 1 second after the ignition switch is turned ON.

CAUTION:

Never start the engine.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Proceed to diagnosis procedure. Refer to 

BRC-84, "Diagnosis Procedure"

.

2.

BRAKE WARNING LAMP OPERATION CHECK 2

Check that the brake warning lamp in the combination meter turns ON/OFF correctly when operating the park-
ing brake pedal.
NOTE:
Brake warning lamp will turn ON in case of parking brake operation (when switch is ON) or of brake fluid level
switch operation (when brake fluid is insufficient).

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Check parking brake switch. Refer to 

BRC-79, "Component Inspection"

.

Diagnosis Procedure

INFOID:0000000009950015

1.

PERFORM SELF-DIAGNOSIS

Perform self-diagnosis for “ABS” with CONSULT.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check item displayed by self-diagnosis.

2.

CHECK COMBINATION METER

Check if the indication and operation of combination meter are normal. Refer to 

MWI-29, "Diagnosis Descrip-

tion"

.

Is the inspection result normal?

YES

>> Replace ABS actuator and electric unit (control unit). Refer to 

BRC-113, "Exploded View"

.

NO

>> Repair or replace error-detected parts.

Special Repair Requirement

INFOID:0000000009950016

1.

ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION

Condition

Brake warning lamp (Note 1)

Ignition switch OFF

–

For 1 second after turning ignition switch ON

×

 (Note 2)

1 second later after turning ignition switch ON

×

 (Note 2)

ABS function is malfunctioning.

–

EBD function is malfunctioning.

×

BRAKE WARNING LAMP

BRC-85

< DTC/CIRCUIT DIAGNOSIS >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

Always perform the neutral position adjustment for the steering angle sensor, when replacing the ABS actua-
tor and electric unit (control unit) or steering angle sensor and removing steering angle sensor. Refer to 

BRC-

9, "Special Repair Requirement"

>> END