Nissan Versa Note. Manual - part 883

REAR WIPER MOTOR CIRCUIT

WW-51

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

3.

 CHECK REAR WIPER MOTOR OPEN CIRCUIT

Check continuity between BCM harness connector and rear wiper motor harness connector.

With Intelligent Key

Without Intelligent Key

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

 CHECK REAR WIPER MOTOR SHORT CIRCUIT

Check continuity between BCM harness connector and ground.

With Intelligent Key

Without Intelligent Key

Is the inspection result normal?

YES

>> Repair or replace harness.

NO

>> Replace BCM. Refer to 

BCS-70, "Removal and Installation"

 (with Intelligent Key) or 

BCS-127,

"Removal and Installation"

 (without Intelligent Key).

BCM

Rear wiper motor

Continuity

Connector

Terminal

Connector

Terminal

M100

54

D502

2

Yes

BCM

Rear wiper motor

Continuity

Connector

Terminal

Connector

Terminal

M20

68

D502

2

Yes

BCM

Ground

Continuity

Connector

Terminal

M100

54

No

BCM

Ground

Continuity

Connector

Terminal

M20

68

No

WW-52

< DTC/CIRCUIT DIAGNOSIS >

REAR WIPER AUTO STOP SIGNAL CIRCUIT

REAR WIPER AUTO STOP SIGNAL CIRCUIT

Component Function Check

INFOID:0000000009643037

1.

 CHECK REAR WIPER (AUTO STOP) OPERATION

CONSULT DATA MONITOR

1. Select WIPER of BCM data monitor item.

2. Operate the rear wiper.

3. Check that RR WIPER STOP changes to ON and OFF linked with the wiper operation.

Is the inspection result normal?

YES

>> Rear wiper auto stop signal circuit is normal.

NO

>> Refer to 

WW-52, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009643038

Regarding Wiring Diagram information, refer to 

WW-32, "Wiring Diagram"

.

1.

 CHECK REAR WIPER MOTOR AUTO STOP CIRCUITS FOR OPEN

1. Turn ignition switch OFF.

2. Disconnect BCM and rear wiper motor.

3. Check continuity between BCM harness connector terminal and rear wiper motor harness connector ter-

minal.

With Intelligent Key

Without Intelligent Key

Is inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness.

2.

 CHECK AUTO STOP CIRCUITS FOR SHORT TO GROUND

Check continuity between BCM harness connector terminal and ground.

With Intelligent Key

Without Intelligent Key

Monitor item

Condition

Monitor status

RR WIPER STOP

Rear wiper motor

Stop position

ON

Except stop position

OFF

BCM

Rear wiper motor

Continuity

Connector

Terminal

Connector

Terminal

M100

44

D502

3

Yes

BCM

Rear wiper motor

Continuity

Connector

Terminal

Connector

Terminal

M20

56

D502

3

Yes

BCM

Ground

Continuity

Connector

Terminal

M100

44

No

BCM

Ground

Continuity

Connector

Terminal

M20

56

No

REAR WIPER AUTO STOP SIGNAL CIRCUIT

WW-53

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

Is inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-70, "Removal and Installation"

 (with Intelligent Key) or 

BCS-127,

"Removal and Installation"

 (with Intelligent Key).

NO

>> Repair or replace harness.

WW-54

< SYMPTOM DIAGNOSIS >

WIPER AND WASHER SYSTEM SYMPTOMS

SYMPTOM DIAGNOSIS

WIPER AND WASHER SYSTEM SYMPTOMS

Symptom Table

INFOID:0000000009643039

CAUTION:

Perform the self-diagnosis with CONSULT before performing the diagnosis by symptom. Perform the

diagnosis by DTC if DTC is detected.