Nissan Versa Note. Manual - part 727

 

  Index      Nissan     Nissan Versa Note (2014 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  725  726  727  728   ..

 

 

Nissan Versa Note. Manual - part 727

 

 

COLLISION DIAGNOSIS

SR-5

< BASIC INSPECTION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

BASIC INSPECTION

COLLISION DIAGNOSIS

For Frontal Collision

INFOID:0000000009478687

FOR FRONTAL COLLISION: When SRS is activated in a collision

CAUTION:

Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.

WORK PROCEDURE

1. Before performing any of the following steps, ensure that all vehicle body and structural repairs have been

completed. 

2. Replace the diagnosis sensor unit.

3. Remove the front air bag modules, crash zone sensor assembly, bracket and seat belt pre-tensioner

assemblies.

4. Check the SRS components using the table below:

Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc.)

5. Install new front air bag modules, crash zone sensor assembly, bracket and seat belt pre-tensioner

assemblies.

6. Perform self-diagnosis using CONSULT or air bag warning lamp. Refer to 

SRC-14, "Description"

 for

details.

Ensure entire SRS operates properly. 

7. After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to

SRC-14, "Description"

.

SRS INSPECTION (FOR FRONTAL COLLISION)

Part

Inspection

Driver air bag module

If the driver air bag has deployed:
REPLACE
Install with new fasteners.

Front passenger air bag module 
(if equipped)

If the front passenger air bag has deployed:
REPLACE
Install with new fasteners.

Crash zone sensor

If any of the front air bags or seat belt pre-tensioners* have been activated:
REPLACE the crash zone sensor and bracket with new fasteners.
*: Confirm seat belt pre-tensioner activation using CONSULT only.

Seat belt pre-tensioner assem-
blies
(All applicable locations: buckle, 
retractor, lap outer)

If either the driver or passenger seat belt pre-tensioner* has been activated:
REPLACE all seat belt pre-tensioner assemblies with new fasteners.
*: Confirm seat belt pre-tensioner activation using CONSULT only.

Diagnosis sensor unit

If any of the SRS components have been activated:
REPLACE the diagnosis sensor unit.
Install with new fasteners.

Steering wheel

1.

Visually check steering wheel for deformities.

2.

Check harness (built into steering wheel) and connectors for damage, and terminals for defor-
mities.

3.

Install driver air bag module into the steering wheel to check fit and alignment with the wheel.

4.

Check steering wheel for excessive free play.

5.

If no damage is found, reinstall.

6.

If damaged — REPLACE.

Spiral cable

If the driver front air bag has deployed:
REPLACE the spiral cable.

SR-6

< BASIC INSPECTION >

COLLISION DIAGNOSIS

FOR FRONTAL COLLISION: When SRS is not activated in a collision

CAUTION:

Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.

WORK PROCEDURE

1. Before performing any of the following steps, ensure that all vehicle body and structural repairs have been

completed. 

2. Check the SRS components using the table below:

Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc.)

3. Perform self-diagnosis using CONSULT or air bag warning lamp. Refer to 

SRC-14, "Description"

 for

details.

Ensure entire SRS operates properly. 

4. After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to

SRC-14, "Description"

.

SRS INSPECTION (FOR FRONTAL COLLISION)

Occupant classification system 
(Passenger seat)

1.

Remove passenger seat assembly.

2.

Check control unit case for dents, cracks of deformities.

3.

Check connectors for damage and terminals for deformities.

4.

Check seat frame and cushion pan for dents or deformities.

5.

If no damage is found, reinstall seat with new fasteners.

6.

If damaged — REPLACE seat cushion assembly with new fasteners.

7.

Perform zero point reset function after front passenger seat is installed in the vehicle and all 
bolts are tightened to specification. Refer to 

SRC-38, "ZERO POINT RESET : Special Repair 

Requirement"

.

Harness and connectors

1.

Check connectors for poor connection, damage, and terminals for deformities.

2.

Check harness for binding, chafing, cuts, or deformities.

3.

If no damage is found, reinstall the harness and connectors.

4.

If damaged — REPLACE the damaged harness. Do not attempt to repair, splice or modify any 
SRS harness.

Instrument panel assembly

If the passenger front air bag has deployed: 
REPLACE the instrument panel assembly. (integrated type)

Part

Inspection

Part

Inspection

Driver air bag module

If the driver air bag has NOT been activated:
1.

Remove driver air bag module. Check harness cover and connectors for damage, terminals 
for deformities, and harness for binding.

2.

Install driver air bag module into the steering wheel to check fit and alignment with the wheel.

3.

If no damage is found, reinstall with new fasteners.

4.

If damaged — REPLACE. Install driver air bag modules with new fasteners.

Front passenger air bag module 
(if equipped)

If the front passenger air bag has NOT been activated:
1.

Remove front passenger air bag module. Check harness cover and connectors for damage, 
terminals for deformities, and harness for binding.

2.

Install front passenger air bag module into the instrument panel to check fit with the instrument 
panel.

3.

If no damage is found, reinstall with new fasteners.

4.

If damaged — REPLACE. Install front passenger air bag modules with new fasteners.

Crash zone sensor

If the front air bags or seat belt pre-tensioners have NOT been activated:
1.

Remove the crash zone sensor. Check harness connectors for damage, terminals for defor-
mities, and harness for binding.

2.

Check for visible signs of damage (dents, cracks, deformation) of the crash zone sensor and 
bracket.

3.

Install the crash zone sensor to check fit.

4.

If no damage is found, reinstall with new fasteners.

5.

If damaged — REPLACE the crash zone sensor and bracket with new fasteners. 

COLLISION DIAGNOSIS

SR-7

< BASIC INSPECTION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

For Side and Rollover Collision

INFOID:0000000009478688

FOR SIDE AND ROLLOVER COLLISION: When SRS is activated in a collision

CAUTION:

Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.

WORK PROCEDURE

1. Before performing any of the following steps, ensure that all vehicle body and structural repairs have been

completed. 

2. Replace the following components:

-

Front seat back assembly (on the side on which side air bag is activated).

-

Door finisher (on the side on which door-mounted curtain air bag is activated).

-

Pop-up roll bar assemblies and pop-up roll bar covers.

-

Side air bag (satellite) sensor LH/RH (on the side on which side air bag is activated).

Seat belt pre-tensioner assem-
blies
(All applicable locations: buckle, 
retractor, lap outer)

If the pre-tensioners have NOT been activated:
1.

Remove seat belt pre-tensioners.
Check harness cover and connectors for damage, terminals for deformities, and harness for 
binding.

2.

Check belts for damage and anchors for loose mounting.

3.

Check retractor for smooth operation.

4.

Check seat belt adjuster for damage.

5.

Check for deformities of the center pillar inner.

6.

If no damage is found, reinstall seat belt pre-tensioner assembly with new fasteners.

7.

If damaged —REPLACE. Install the seat belt pre-tensioner assembly with new fasteners. 

Diagnosis sensor unit

If none of the SRS components have been activated:
1.

Check case for dents, cracks or deformities.

2.

Check connectors for damage, and terminals for deformities.

3.

If no damage is found, reinstall with new fasteners.

4.

If damaged — REPLACE. Install diagnosis sensor unit with new fasteners.

Steering wheel

1.

Visually check steering wheel for deformities.

2.

Check harness (built into steering wheel) and connectors for damage, and terminals for defor-
mities.

3.

Install driver air bag module into the steering wheel to check fit and alignment with the wheel.

4.

Check steering wheel for excessive free play.

5.

If no damage is found, reinstall.

6.

If damaged — REPLACE.

Spiral cable

If the driver front air bag has not deployed:
1.

Visually check spiral cable and combination switch for damage.

2.

Check connectors and protective tape for damage.

3.

Check steering wheel for noise, binding or heavy operation.

4.

If no damage is found, reinstall.

5.

If damaged — REPLACE.

Occupant classification system 
(Passenger seat)

1.

Remove passenger seat assembly.

2.

Check control unit case for dents, cracks of deformities.

3.

Check connectors for damage and terminals for deformities.

4.

Check seat frame and cushion pan for dents or deformities.

5.

If no damage is found, reinstall seat with new fasteners.

6.

If damaged — REPLACE seat cushion assembly with new fasteners.

7.

Perform zero point reset function after front passenger seat is installed in the vehicle and all 
bolts are tightened to specification. Refer to 

SRC-38, "ZERO POINT RESET : Special Repair 

Requirement"

.

Harness and connectors

1.

Check connectors for poor connection, damage, and terminals for deformities.

2.

Check harness for binding, chafing, cuts, or deformities.

3.

If no damage is found, reinstall the harness and connectors.

4.

If damaged ——REPLACE the damaged harness. Do not attempt to repair, splice or modify 
any SRS harness.

Instrument panel assembly

If the passenger front air bag has NOT deployed:
1.

Visually check instrument panel for damage.

2.

If no damage is found, reinstall the instrument panel assembly.

3.

If damaged—REPLACE the instrument panel assembly.

Part

Inspection

SR-8

< BASIC INSPECTION >

COLLISION DIAGNOSIS

-

Diagnosis sensor unit.

-

Seat belt pre-tensioner assemblies.

3. Check the SRS components and the related parts using the following table.

Replace any SRS components and the related parts showing visible signs of damage (dents, cracks,

deformation, etc.).

4. Perform self-diagnosis using CONSULT and “AIR BAG” warning lamp. Refer to 

SRC-14, "Description"

 for

details. Make sure entire SRS operates properly.

5. After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to

SRC-14, "Description"

.

SRS INSPECTION (FOR SIDE AND ROLLOVER COLLISION)

Part

Inspection

Side curtain air bag module LH

If the side curtain air bag LH has deployed:
REPLACE the side curtain air bag module LH.
Install with new fasteners.

Side curtain air bag module RH

If the side curtain air bag RH has deployed:
REPLACE the side curtain air bag module RH.
Install with new fasteners.

Front side air bag module LH

If the front side air bag LH has deployed: 
REPLACE front seatback assembly LH.

Front side air bag module RH

If the front side air bag RH has deployed:
REPLACE front seatback assembly RH.

Side air bag (satellite) sensor (LH 
or RH) 

If any of the SRS components have deployed:
REPLACE the side air bag (satellite) sensor on the collision side with new fasteners.

Door (satellite) sensor (LH or RH)  If any of the SRS components have deployed:

REPLACE the door (satellite) sensor on the collision side with new fasteners.

Diagnosis sensor unit

If any of the SRS components have deployed:
REPLACE the diagnosis sensor unit with new fasteners.

Seat belt pre-tensioner assem-
blies
(All applicable locations: buckle, 
retractor, lap outer)

If either the driver or passenger seat belt pre-tensioner* has been activated:
REPLACE all seat belt pre-tensioner assemblies with new fasteners.
*: Confirm seat belt pre-tensioner activation using CONSULT only.

Center inner pillar

1.

Check the center inner pillar on the collision side for damage (dents, cracks, deformation).

2.

If damaged —REPAIR the center inner pillar.

Seat (if equipped with front side 
air bag)

If either the front LH or front RH side air bag modules has been deployed:
REPLACE front seatback assembly on the deployed side.

Trim/headlining

1.

Check for visible signs of damage (dents, cracks, deformation) of the interior trim on the colli-
sion side.

2.

If damaged — REPLACE the damaged trim parts.

Door-mounted curtain air bag 
module LH

If the door-mounted curtain air bag module LH has been deployed: 
REPLACE the door finisher LH and door-mounted curtain air bag module.
Install with new fasteners.

Door-mounted curtain air bag 
module RH

If the door-mounted curtain air bag module RH has been deployed: 
REPLACE the door finisher RH and door-mounted curtain air bag module.
Install with new fasteners.

Occupant classification system 
(Passenger seat)

1.

Remove passenger seat assembly.

2.

Check control unit case for dents, cracks of deformities.

3.

Check connectors for damage and terminals for deformities.

4.

Check seat frame and cushion pan for dents or deformities.

5.

If no damage is found, reinstall seat with new fasteners.

6.

If damaged — REPLACE seat cushion assembly with new fasteners.

7.

Perform zero point reset function after front passenger seat is installed in the vehicle and all 
bolts are tightened to specification. Refer to 

SRC-38, "ZERO POINT RESET : Special Repair 

Requirement"

.

Pop-up roll bar assemblies

If the pop-up roll bar has deployed:
REPLACE pop-up roll bar assemblies and pop-up roll bar covers.
Install with new fasteners.

 

 

 

 

 

 

 

Content   ..  725  726  727  728   ..