Nissan Versa Note. Manual - part 710

B210E STARTER RELAY

SEC-119

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

NO (WITH CVT)>>GO TO 4.

3.

CHECK STARTER CONTROL RELAY CONTROL CIRCUIT CONTINUITY

1. Disconnect IPDM E/R connector E44 and clutch interlock switch connector E34.

2. Check continuity between IPDM E/R connector E44 and clutch interlock switch connector E34.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-70, "Removal and Installation"

.

NO

>> Repair or replace harness or connectors.

4.

CHECK STARTER CONTROL RELAY CONTROL CIRCUIT CONTINUITY

1. Disconnect IPDM E/R connector F42 and transmission range switch connector F52.

2. Check continuity between IPDM E/R connector F42 and transmission range switch connector F52.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-70, "Removal and Installation"

.

NO

>> Repair or replace harness or connectors.

IPDM E/R

Clutch interlock switch

Continuity

Connector

Terminal

Connector

Terminal

E44

13

E34

2

Yes

IPDM E/R

Transmission range switch

Continuity

Connector

Terminal

Connector

Terminal

F42

40

F52

10

Yes

SEC-120

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH

B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH

DTC Logic

INFOID:0000000009705932

DTC DETECTION LOGIC

NOTE:

If DTC B210F is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to 

BCS-

60, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Shift selector lever to the P position.

2. Turn ignition switch ON and wait 1 second or more.

3. Shift selector lever to the N position and wait 1 second or more.

4. Shift selector lever to the position other than P and N, and wait 1 second or more.

5. Check DTC in Self Diagnostic Result mode of IPDM E/R using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-120, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure 

INFOID:0000000009705933

Regarding Wiring Diagram information, refer to 

SEC-40, "Wiring Diagram"

.

1.

CHECK DTC OF BCM

Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?

YES

>> Perform the trouble diagnosis related to the detected DTC. Refer to 

BCS-48, "DTC Index"

.

NO

>> GO TO 2.

2.

CHECK IPDM E/R SIGNAL CIRCUIT OPEN AND SHORT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector.

3. Disconnect transmission range switch connector.

4. Check continuity between IPDM E/R harness connector and transmission range switch harness connec-

tor.

5. Check continuity between IPDM E/R harness connector and ground.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B210F

INTRLCK/PNP SW ON

IPDM E/R detects a difference between the 
following signals
• P/N position signal from transmission 

range switch and P/N position signal 
(CAN) from BCM 

• Harness or connectors

(The CAN communication line is open 
or shorted.)

• Harness or connectors

(Transmission range switch circuit is 
open or shorted.)

• Transmission range switch
• IPDM  E/R
• BCM

IPDM E/R

Transmission range switch

Continuity

Connector

Terminal

Connector

Terminal

F42

40

F52

10

Yes

B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH

SEC-121

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-31, "Removal and Installation"

.

NO

>> Repair or replace harness.

(+)

(–)

Continuity

IPDM E/R

Connector

Terminal

F42

40

Ground

No

SEC-122

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH

B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH

DTC Logic

INFOID:0000000009705934

DTC DETECTION LOGIC

NOTE:

If DTC B2110 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to 

BCS-

60, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Shift selector lever to the P position.

2. Turn ignition switch ON and wait 1 second or more.

3. Shift selector lever to the N position and wait 1 second or more.

4. Shift selector lever to the position other than P and N, and wait 1 second or more.

5. Check DTC in Self Diagnostic Result mode of IPDM E/R using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-122, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure 

INFOID:0000000009705935

Regarding Wiring Diagram information, refer to 

SEC-40, "Wiring Diagram"

.

1.

CHECK DTC OF BCM

Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?

YES

>> Perform the trouble diagnosis related to the detected DTC. Refer to 

BCS-48, "DTC Index"

.

NO

>> GO TO 2.

2.

CHECK IPDM E/R SIGNAL CIRCUIT OPEN AND SHORT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector.

3. Disconnect transmission range switch connector.

4. Check continuity between IPDM E/R harness connector and transmission range switch harness connec-

tor.

5. Check continuity between IPDM E/R harness connector and ground.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B210F

INTRLCK/PNP SW OFF

IPDM E/R detects a difference between the 
following signals
• P/N position signal from transmission 

range switch and P/N position signal 
(CAN) from BCM 

• Harness or connectors

(The CAN communication line is open 
or shorted.)

• Harness or connectors

(Transmission range switch circuit is 
open or shorted.)

• Transmission range switch
• IPDM E/R
• BCM

IPDM E/R

Transmission range switch

Continuity

Connector

Terminal

Connector

Terminal

F42

40

F52

10

Yes