Nissan Versa Note. Manual - part 685

SYSTEM

SEC-19

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

switches to the ARMED phase when vehicle conditions are not changed for 30 seconds. Security indicator

lamp illuminates while being in this phase.

To reset the PRE-ARMED phase, refer to the switching condition of No. 10 in the table above.

ARMED Phase

The vehicle security system is set and BCM monitors all necessary inputs. If any door is opened without using

Intelligent Key, vehicle security system switches to the ALARM phase. Security indicator lamp blinks every 2.4

seconds.

To reset the ARMED phase, refer to the switching condition of No. 11 in the table above.

ALARM Phase

BCM transmits “Theft Warning Horn Request” signal and “High Beam Request” signal intermittently to IPDM

E/R via CAN communication. In this phase, horns and headlamps are activated intermittently for approxi-

mately 50 seconds to warn that the vehicle is accessed by unauthorized means. ON/OFF timing of horns and

headlamps are synchronized. After 50 seconds, the vehicle security system returns to the ARMED phase. At

this time, if BCM still detects unauthorized access to the vehicle, the system is switched to the ALARM phase

again. This RE-ALARM operation is carried out a maximum of 2 times.

To cancel the ALARM operation, refer to the switching condition of No. 12 in the table above.

NOTE:

If a battery terminal is disconnected during the ALARM phase, theft warning alarm stops. But when the battery

terminal is reconnected, theft warning alarm is activated again.

PANIC ALARM

• The panic alarm function activates horns and headlamps intermittently when the owner presses the PANIC

ALARM button of Intelligent Key outside the vehicle while the power supply position is OFF or LOCK.

• When BCM receives panic alarm signal from Intelligent Key, BCM transmits “Theft Warning Horn Request”

signal and “High Beam Request” signal intermittently to IPDM E/R via CAN communication. To prevent the

activation due to mis-operation of Intelligent Key by owner, the panic alarm function is activated when BCM

receives the signal for 0.4 - 0.6 seconds.

• Panic alarm operation is maintained for 25 seconds.

• Panic alarm operation is cancelled when BCM receives one of the following signals:

- LOCK button of Intelligent Key: ON

- UNLOCK button of Intelligent Key: ON

- PANIC ALARM button of Intelligent Key: Long pressed

- Any door request switch: ON

SEC-20

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

DIAGNOSIS SYSTEM (BCM)

COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)

INFOID:0000000009697556

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with BCM.

SYSTEM APPLICATION

BCM can perform the following functions.

Direct Diagnostic Mode

Description

ECU identification

The BCM part number is displayed.

Self Diagnostic Result

The BCM self diagnostic results are displayed.

Data Monitor

The BCM input/output data is displayed in real time.

Active Test

The BCM activates outputs to test components.

Work support

The settings for BCM functions can be changed.

Configuration

• The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing BCM.

CAN DIAG SUPPORT MNTR

The result of transmit/receive diagnosis of CAN communication is displayed.

System

Sub System

Direct Diagnostic Mode

ECU id

en

tif

ica

tion

Se

lf Di

ag

no

st

ic

 Res

u

lt

Dat

a

 M

on

ito

r

Acti

ve

 T

est

W

o

rk

 su

pp

ort

Co

nf

ig

ur

at

io

n

CAN DIAG SUP

P

OR

T MNTR

Door lock

DOOR LOCK

×

×

×

×

Rear window defogger

REAR DEFOGGER

×

×

Warning chime

BUZZER

×

×

Interior room lamp timer

INT LAMP

×

×

×

Exterior lamp

HEAD LAMP

×

×

×

Wiper and washer

WIPER

×

×

×

Turn signal and hazard warning lamps FLASHER

×

×

Air conditioner

AIR CONDITIONER

×

Intelligent Key system

INTELLIGENT KEY

×

×

×

×

Combination switch

COMB SW

×

BCM

BCM

×

×

×

×

×

Immobilizer

IMMU

×

×

×

Interior room lamp battery saver

BATTERY SAVER

×

×

×

Vehicle security system

THEFT ALM

×

×

×

RAP system

RETAINED PWR

×

×

Signal buffer system

SIGNAL BUFFER

×

TPMS

AIR PRESSURE MONITOR

×

×

×

×

Panic alarm system

PANIC ALARM

×

DIAGNOSIS SYSTEM (BCM)

SEC-21

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

INTELLIGENT KEY
INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)

INFOID:0000000009697557

SELF DIAGNOSTIC RESULT

Refer to 

BCS-48, "DTC Index"

.

DATA MONITOR

ACTIVE TEST

Monitor Item [Unit]

Main

Description

REQ SW -DR [On/Off]

×

Indicates condition of door request switch LH.

REQ SW -AS [On/Off]

×

Indicates condition of door request switch RH.

REQ SW -BD/TR [On/Off]

×

Indicates condition of back door request switch.

PUSH SW [On/Off]

Indicates condition of push-button ignition switch.

CLUTCH SW [On/Off]

×

Indicates condition of clutch interlock switch.

BRAKE SW 1 [On/Off]

×

Indicates condition of brake switch.

BRAKE SW 2 [On/Off]

Indicates condition of brake switch.

DETE/CANCL SW [On/Off]

×

Indicates condition of P (park) position.

SFT PN/N SW [On/Off]

×

Indicates condition of P (park) or N (neutral) position.

UNLK SEN -DR [On/Off]

×

Indicates condition of door unlock sensor.

PUSH SW -IPDM [On/Off]

Indicates condition of push-button ignition switch received from IPDM E/R on 
CAN communication line.

IGN RLY1 -F/B [On/Off]

Indicates condition of ignition relay 1 received from IPDM E/R on CAN commu-
nication line.

DETE SW -IPDM [On/Off]

Indicates condition of detent switch received from TCM on CAN communication 
line.

SFT PN -IPDM [On/Off]

Indicates condition of P (park) or N (neutral) position from TCM on CAN com-
munication line.

SFT P -MET [On/Off]

Indicates condition of P (park) position from TCM on CAN communication line.

SFT N -MET [On/Off]

Indicates condition of N (neutral) position from IPDM E/R on CAN communica-
tion line.

ENGINE STATE [Stop/Start/Crank/Run]

×

Indicates condition of engine state from ECM on CAN communication line.

VEH SPEED 1 [mph/km/h]

×

Indicates condition of vehicle speed signal received from ABS on CAN commu-
nication line.

VEH SPEED 2 [mph/km/h]

×

Indicates condition of vehicle speed signal received from combination meter on 
CAN communication line.

DOOR STAT -DR [LOCK/READY/UNLK]

×

Indicates condition of driver side door status.

DOOR STAT -AS [LOCK/READY/UNLK]

×

Indicates condition of passenger side door status.

ID OK FLAG [Set/Reset]

Indicates condition of Intelligent Key ID.

PRMT ENG STRT [Set/Reset]

Indicates condition of engine start possibility.

RKE OPE COUN1 [0-19]

×

When remote keyless entry receiver receives the signal transmitted while oper-
ating on Intelligent Key, the numerical value start changing.

RKE OPE COUN2 [0-19]

×

When remote keyless entry receiver receives the signal transmitted while oper-
ating on Intelligent Key, the numerical value start changing.

RKE-LOCK [On/Off]

Indicates condition of lock signal from Intelligent Key.

RKE-UNLOCK [On/Off]

Indicates condition of unlock signal from Intelligent Key.

RKE-PANIC [On/Off]

Indicates condition of panic signal from Intelligent Key.

RKE-MODE CHG [On/Off]

Indicates condition of mode change signal from Intelligent Key.

SEC-22

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

WORK SUPPORT

Test Item

Description

INSIDE BUZZER

This test is able to check combination meter warning chime operation [Take Out/Knob/Key/
Off].

LCD

This test is able to check combination meter display information [Off/LK WN/OUTKEY/NO 
KY/BATT/INSRT/SFT P/ROTAT/ID NG/B&P I/B&P N].

BATTERY SAVER

This test is able to check battery saver operation [On/Off].

ENGINE SW ILLUMI

This test is able to check push-button ignition switch START indicator operation [On/Off].

PUSH SWITCH INDICATOR

This test is able to check push-button ignition switch indicator operation [On/Off].

INT LAMP

This test is able to check interior room lamp operation [On/Off].

INDICATOR

This test is able to check combination meter warning lamp operation [KEY ON/KEY IND/Off].

FLASHER

This test is able to check hazard lamp operation [LH/RH/Off].

OUTSIDE BUZZER

This test is able to check Intelligent Key warning buzzer operation [On/Off].

HORN

This test is able to check horn operation [On].

P RANGE

This test is able to check CVT shift selector illumination operation [On/Off].

Support Item

Setting

Description

LOCK/UNLOCK BY I-KEY

On*

Door lock/unlock function from Intelligent Key ON. 

Off

Door lock/unlock function from Intelligent Key OFF. 

ANTI KEY LOCK IN FUNCTI

On*

Anti lock out setting ON.

Off

Anti lock out setting OFF.

ANS BACK I-KEY UNLOCK

Off

No buzzer reminder when doors are unlocked with request switch.

On*

Buzzer reminder when doors are unlocked with request switch.

ANS BACK I-KEY LOCK

Horn Chirp

Horn chirp reminder when doors are locked with request switch.

Buzzer*

Buzzer reminder when doors are locked with request switch.

Off

No reminder when doors are locked with request switch.

HORN WITH KEYLESS LOCK

Off

Horn chirp reminder when doors are locked with Intelligent Key.

On*

No horn chirp reminder when doors are locked with Intelligent Key.

HAZARD ANSWER BACK

Lock/Unlock*

Hazard warning lamp activation when doors are locked/unlocked 
with Intelligent Key or request switch.

Unlock Only

Hazard warning lamp activation when doors are unlocked with Intel-
ligent Key or request switch.

Lock Only

Hazard warning lamp activation when doors are locked with Intelli-
gent Key or request switch.

Off

No hazard warning lamp activation when doors are locked/unlocked 
with Intelligent Key or request switch.

INSIDE ANT DIAGNOSIS

—

This function allows inside key antenna self-diagnosis.

CONFIRM KEY FOB ID

—

Intelligent Key ID code can be checked.

SHORT CRANKING OUTPUT

Start

70 msec

Starter motor operation duration time setting.

100 msec

200 msec

End

—

PANIC ALARM SET

MODE 3

1.5 sec

Intelligent Key panic alarm button setting.

MODE 2

OFF

MODE 1*

0.5 sec

LO- BATT OF KEY FOB WARN

On*

Intelligent Key low battery warning ON. 

Off

Intelligent Key low battery warning OFF.