Nissan Versa Note. Manual - part 591

MWI

B2205 VEHICLE SPEED

MWI-39

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

B2205 VEHICLE SPEED

Description

INFOID:0000000009654114

The ABS actuator and electric unit (control unit) provides a vehicle speed signal to the combination meter via

CAN communication lines.

DTC Logic

INFOID:0000000009654115

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000009654116

1.

CHECK COMBINATION METER INPUT SIGNAL

1. Start engine and select METER/M&A on CONSULT.

2. Using SPEED METER on DATA MONITOR, compare the value of DATA MONITOR with speedometer

pointer of combination meter. Speedometer and DATA MONITOR indications should be close.

Is the inspection result normal?

YES

>> Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to 

BRC-30, "CONSULT

Function (ABS)"

.

NO

>> Replace combination meter. Refer to 

MWI-54, "Removal and Installation"

.

DTC

Display Item

Malfunction detected condition

Possible malfunction 

B2205

VEHICLE SPEED CIRC
[B2205]

Malfunction is detected when an erroneous 
speed signal is received for 2 seconds or more.

• Combination meter
• ABS actuator and electric unit (control unit)

MWI-40

< DTC/CIRCUIT DIAGNOSIS >

B2267 ENGINE SPEED

B2267 ENGINE SPEED

Description

INFOID:0000000009654117

The engine speed signal is transmitted from ECM to the combination meter via CAN communication.

DTC Logic

INFOID:0000000009654118

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000009654119

1.

PERFORM SELF-DIAGNOSIS OF ECM

Perform Self Diagnostic Result of ECM, and repair or replace malfunctioning parts.

>> Refer to  

EC-60, "CONSULT Function"

.

DTC

Display Item

Malfunction detected condition

Possible malfunction

B2267

TACHO METER
[B2267]

ECM continuously transmits abnormal engine 
speed signals for 2 seconds or more 

• Crankshaft position sensor (POS)
• ECM

MWI

B2268 WATER TEMP

MWI-41

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

B2268 WATER TEMP

Description

INFOID:0000000009654120

The engine coolant temperature signal is transmitted from ECM to the combination meter via CAN communi-

cation.

DTC Logic

INFOID:0000000009654121

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000009654122

1.

PERFORM SELF-DIAGNOSIS OF ECM

Perform Self Diagnostic Result of ECM, and repair or replace malfunctioning parts.

>> Refer to 

EC-60, "CONSULT Function"

.

DTC

Display Item

Malfunction detected condition

Possible malfunction

B2268

WATER TEMP METER
[B2268]

ECM continuously transmits abnormal engine coolant 
temperature signals for 60 seconds or more 

• Engine coolant temperature sensor
• ECM

MWI-42

< DTC/CIRCUIT DIAGNOSIS >

POWER SUPPLY AND GROUND CIRCUIT

POWER SUPPLY AND GROUND CIRCUIT

COMBINATION METER
COMBINATION METER : Diagnosis Procedure

INFOID:0000000009654123

Regarding Wiring Diagram information, refer to 

MWI-23, "Wiring Diagram"

.

1.

CHECK FUSE

Check that the following fuses are not blown.

Is the fuse blown?

YES

>> GO TO 2.

NO

>> Replace the blown fuse after repairing the affected circuit.

2.

POWER SUPPLY CIRCUIT CHECK

1. Disconnect combination meter connector.

2. Check voltage between combination meter harness connector M24,  terminals 27, 28, 15 and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness or connector.

3.

GROUND  CIRCUIT CHECK

1. Turn ignition switch OFF.

2. Disconnect combination meter connector.

3. Check continuity between combination meter harness connector M24, terminals 21, 22, 23 and ground.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Repair or replace harness or connector.

BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM)
BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM) : Diagnosis 

Power source

Fuse No.

Battery

8

Ignition switch ON or START 

3

Ignition switch ACC or ON 

18

Terminals

Ignition switch position

(+)

(–)

OFF

ACC

ON

START

Connector

Terminal

M24

27

Ground

Battery voltage

Battery voltage

Battery voltage

Battery voltage

28

0V

0V

Battery voltage

Battery voltage

15

0V

Battery voltage

Battery voltage

0V

Terminals

Continuity

(+)

(–)

Connector

Terminal

M24

21

Ground

Yes

22

23