Nissan Versa Note. Manual - part 118

BRC-36

< ECU DIAGNOSIS INFORMATION >

[VDC/TCS/ABS]

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

RR RH OUT SOL

Operation status of all solenoid valves 

Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT) or actuator 
relay is inactive (in fail-safe mode)

On

When the actuator (solenoid valve) is not 
active and actuator relay is active (igni-
tion switch ON)

Off

RR LH IN SOL

Operation status of all solenoid valves 

Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT) or actuator 
relay is inactive (in fail-safe mode)

On

When the actuator (solenoid valve) is not 
active and actuator relay is active (igni-
tion switch ON)

Off

RR LH OUT SOL

Operation status of all solenoid valves 

Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT) or actuator 
relay is inactive (in fail-safe mode)

On

When the actuator (solenoid valve) is not 
active and actuator relay is active (igni-
tion switch ON)

Off

EBD WARN LAMP

EBD warning lamp
(Note 2)

When EBD warning lamp is ON

On

When EBD warning lamp is OFF

Off

STOP LAMP SW

Brake pedal operation

When brake pedal is depressed

On

When brake pedal is not depressed

Off

MOTOR RELAY

Motor and motor relay operation

When the motor relay and motor are op-
erating

On

When the motor relay and motor are not 
operating

Off

ACTUATOR RLY

Actuator relay operation

When the actuator relay is operating

On

When the actuator relay is not operating

Off

ABS WARN LAMP

ABS warning lamp
(Note 2)

When ABS warning lamp is ON

On

When ABS warning lamp is OFF

Off

OFF LAMP

VDC OFF indicator lamp
(Note 2)

When VDC OFF indicator lamp is ON

On

When VDC OFF indicator lamp is OFF

Off

OFF SW

VDC OFF switch

When VDC OFF switch is in ON

On

When VDC OFF switch is in OFF

Off

SLIP/VDC LAMP

SLIP indicator lamp
(Note 2)

When SLIP indicator lamp is ON

On

When SLIP indicator lamp is OFF

Off

BATTERY VOLT

Battery voltage supplied to the ABS actuator 
and electric unit (control unit)

Ignition switch ON

10 – 16 V

 GEAR

Manual mode gear position determined by 
TCM

1st gear
2nd gear
3rd gear
4th gear
5th gear

1
2
3
4
5

SLCT LVR POSI

Selector lever position.

Vehicle stopped

N/P

ENGINE SPEED

With engine running

When engine running

RPM

YAW RATE SEN

Yaw rate detected by yaw rate/side G sensor

When vehicle stop

Approx. 0 d/s

When vehicle turning

-75 to 75 d/s

R POSI SIG

Transmission range switch signal ON/OFF 
condition

CVT shift position = R position

On

CVT shift position = other than R position

Off

 Monitor item

Display content

Data monitor

Condition

Reference value in 

normal operation

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

BRC-37

< ECU DIAGNOSIS INFORMATION >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

N POSI SIG

Transmission range switch signal ON/OFF 
condition

CVT shift position = N position

On

CVT shift position = other than N position

Off

P POSI SIG

Transmission range switch signal ON/OFF 
condition

CVT shift position = P position

On

CVT shift position = other than P position

Off

CV1

ABS actuator cut valve 1

When the cut valve is active

On

When the cut valve is inactive

Off

CV2

ABS actuator cut valve 2

When the cut valve is active

On

When the cut valve is inactive

Off

SV1

ABS actuator suction valve

When the suction valve is active

On

When the suction valve is inactive

Off

SV2

ABS actuator suction valve 2

When the suction valve is active

On

When the suction valve is inactive

Off

ACCEL POS SIG 

Throttle actuator opening/closing is dis-
played (linked with accelerator pedal)

Accelerator pedal not depressed (ignition 
switch is ON)

0 %

Depress accelerator pedal (ignition 
switch is ON)

0 - 100 %

SIDE G-SENSOR

Transverse G detected by side G sensor

Vehicle stopped

Approx. 0 m/s

2

Vehicle turning right

Negative value 

(m/s

2

)

Vehicle turning left

Positive value

(m/s

2

)

STR ANGLE SIG

Steering angle detected by steering angle 
sensor

Straight-ahead

Approx. 0

°

Steering wheel turned

–720 to 720

°

PRESS SENSOR

Brake fluid pressure detected by pressure 
sensor

With ignition switch turned ON and brake 
pedal released

Approx. 0 bar

With ignition switch turned ON and brake 
pedal depressed

–40 to 300 bar

EBD SIGNAL

EBD operation

EBD is active

On

EBD is inactive

Off

ABS SIGNAL

ABS operation

ABS is active

On

ABS is inactive

Off

TCS SIGNAL

TCS operation

TCS is active

On

TCS is inactive

Off

VDC SIGNAL

VDC operation

VDC is active

On

VDC is inactive

Off

EBD FAIL SIG

EBD fail-safe signal

In EBD fail-safe

On

EBD is normal

Off

ABS FAIL SIG

ABS fail-safe signal

In ABS fail-safe

On

ABS is normal

Off

TCS FAIL SIG

TCS fail-safe signal

In TCS fail-safe

On

TCS is normal

Off

VDC FAIL SIG

VDC fail-safe signal

In VDC fail-safe

On

VDC is normal

Off

 Monitor item

Display content

Data monitor

Condition

Reference value in 

normal operation

BRC-38

< ECU DIAGNOSIS INFORMATION >

[VDC/TCS/ABS]

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

Note 1: Confirm tire pressure is normal.
Note 2: On and off timing for warning lamps and indicator lamps.
• Refer to 

BRC-21, "VDC/TCS/ABS : VDC Function"

.

• Refer to 

BRC-23, "VDC/TCS/ABS : TCS Function"

.

• Refer to 

BRC-25, "VDC/TCS/ABS : ABS Function"

.

• Refer to 

BRC-26, "VDC/TCS/ABS : EBD Function"

.

Fail-safe

INFOID:0000000009364897

VDC AND TCS FUNCTIONS

VDC warning lamp in combination meter turns ON when a malfunction occurs in system [ABS actuator and

electric unit (control unit)]. The control is suspended for VDC and TCS functions. However, ABS and EBD

functions operate normally.

ABS FUNCTION

ABS warning lamp and SLIP indicator lamp in combination meter turn ON when a malfunction occurs in sys-

tem [ABS actuator and electric unit (control unit)]. The control is suspended for VDC, TCS and ABS functions.

However, EBD functions operate normally.

EBD FUNCTION

ABS warning lamp, brake warning lamp and SLIP indicator lamp in combination meter turn ON when a mal-

function occurs in system [ABS actuator and electric unit (control unit)]. The control is suspended for VDC,

TCS, ABS and EBD functions.

CRANKING SIG

Crank operation

Crank is active

On

Crank is inactive

Off

FLUID LEV SW

Brake fluid level switch

When brake fluid level switch ON

On

When brake fluid level switch OFF 

Off

 Monitor item

Display content

Data monitor

Condition

Reference value in 

normal operation

ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

BRC-39

< ECU DIAGNOSIS INFORMATION >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

DTC

Malfunction detected condition

Fail-safe condition

C1101

When an open circuit is detected in rear RH wheel sensor circuit.

The following functions are sus-
pended:
• VDC
• ABS
• EBD (only when both rear wheels 

are malfunctioning)

C1102

When an open circuit is detected in rear LH wheel sensor circuit.

C1103

When an open circuit is detected in front RH wheel sensor circuit.

C1104

When an open circuit is detected in front LH wheel sensor circuit.

C1105

• When a short circuit is detected in rear RH wheel sensor circuit.
• When power supply voltage of rear RH wheel sensor is in following state.
- Rear RH wheel sensor power supply voltage: 7.2 V 

≥ Rear RH wheel sensor pow-

er supply voltage

• When distance between rear RH wheel sensor and rear RH wheel sensor rotor is 

large.

• When installation of rear RH wheel sensor or rear RH wheel sensor rotor is not 

normal.

C1106

• When a short circuit is detected in rear LH wheel sensor circuit.
• When power supply voltage of rear LH wheel sensor is in following state.
- Rear LH wheel sensor power supply voltage: 7.2 V 

≥ Rear LH wheel sensor power 

supply voltage

• When distance between rear LH wheel sensor and rear LH wheel sensor rotor is 

large.

• When installation of rear LH wheel sensor or rear LH wheel sensor rotor is not nor-

mal.

C1107

• When a short circuit is detected in front RH wheel sensor circuit.
• When power supply voltage of front RH wheel sensor is in following state.
- Front RH wheel sensor power supply voltage: 7.2 V 

≥ Front RH wheel sensor 

power supply voltage

• When distance between front RH wheel sensor and front RH wheel sensor rotor 

is large.

• When installation of front RH wheel sensor or front RH wheel sensor rotor is not 

normal.

C1108

• When a short circuit is detected in front LH wheel sensor circuit.
• When power supply voltage of front LH wheel sensor is in following state.
- Front LH wheel sensor power supply voltage: 7.2 V 

≥ Front LH wheel sensor pow-

er supply voltage

• When distance between front LH wheel sensor and front LH wheel sensor rotor is 

large.

• When installation of front LH wheel sensor or front LH wheel sensor rotor is not 

normal.

C1109

• When ignition power supply voltage is in following state.
- Ignition power supply voltage: 10 V 

≥ Ignition power supply voltage.

- Ignition power supply voltage: 16 V 

≤ Ignition power supply voltage.

The following functions are sus-
pended:
• VDC
• TCS
• ABS
• EBD

C1110

When there is an internal malfunction in the ABS actuator and electric unit (control 
unit).

C1111

When a malfunction is detected in motor or motor relay.

The following functions are sus-
pended:
• VDC
• TCS
• ABS

C1115

When difference in wheel speed between any wheel and others is detected when 
the vehicle is driven, because of installation of tires other than specified.

The following functions are sus-
pended:
• VDC
• TCS
• ABS
• EBD

C1116

When stop lamp switch signal is not input when brake pedal operates.

The following functions are sus-
pended:
• VDC
• TCS