Nissan Rogue. Manual - part 947

PCS-34

< BASIC INSPECTION >

[IPDM E/R]

CONFIGURATION (IPDM E/R)

HLL (HEAD LIGHT LEVELING) (IF EQUIPPED)

SETTING ITEM

NOTE

Items

Setting value

SEAT

3-ROW SEAT 

⇔ 2-ROW SEAT

• 3-ROW SEAT: With 3rd row seating
• 2-ROW SEAT: Without 3rd row seating

PCS

U1000 CAN COMM CIRCUIT

PCS-35

< DTC/CIRCUIT DIAGNOSIS >

[IPDM E/R]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

DTC/CIRCUIT DIAGNOSIS

U1000 CAN COMM CIRCUIT

Description

INFOID:0000000011277086

Refer to 

LAN-8, "System Description"

.

DTC Logic

INFOID:0000000011277087

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000011277088

1.

 PERFORM SELF DIAGNOSTIC RESULT

1. Turn ignition switch ON and wait for 2 second or more.

2. Check “Self Diagnostic Result” of “IPDM E/R”.
Is “CAN COMM CIRCUIT” displayed?

YES

>> Refer to 

LAN-17, "Trouble Diagnosis Flow Chart"

.

NO

>> Refer to 

GI-44, "Intermittent Incident"

.

CONSULT Display

DTC Detection Condition

Possible Cause

CAN COMM CIRCUIT
[U1000]

When IPDM E/R cannot communicate with CAN com-
munication signal continuously for 2 seconds or more.

In CAN communication system, any item (or items) of 
the following listed below is malfunctioning:
• Transmission
• Receiving (ECM)
• Receiving (BCM)
• Receiving (Combination meter)

PCS-36

< DTC/CIRCUIT DIAGNOSIS >

[IPDM E/R]

B120E IPDM E/R

B120E IPDM E/R

DTC Logic

INFOID:0000000011277089

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION

1. Turn ignition switch ON.

2. Turn ignition switch OFF and wait 1 second or more.

3. Turn ignition switch ON.

4. Perform “Self Diagnostic Result” of “IPDM E/R” using CONSULT.
Is DTC B120E displayed?

YES

>> Refer to 

PCS-37, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011277090

1.

 PERFORM SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “IPDM E/R” using CONSULT.
Is display history of DTC B120E CRNT?

YES

>> Replace IPDM E/R. Refer to 

PCS-40, "Removal and Installation"

.

NO

>> Refer to 

GI-44, "Intermittent Incident"

.

CONSULT Display

DTC Detection Condition

Possible Cause

USM ECU Not configured
[B120E]

The IPDM E/R detects 0V for greater than 2 sec-
onds. ECU internal failure.

IPDM E/R

PCS

B20DD IGNITION RELAY ON CIRCUIT

PCS-37

< DTC/CIRCUIT DIAGNOSIS >

[IPDM E/R]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

B20DD IGNITION RELAY ON CIRCUIT

DTC Logic

INFOID:0000000011277091

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION

1. Turn ignition switch ON.

2. Turn ignition switch OFF and wait 1 second or more.

3. Turn ignition switch ON.

4. Perform “Self Diagnostic Result” of “IPDM E/R” using CONSULT.
Is DTC B20DD displayed?

YES

>> Refer to 

PCS-37, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011277092

1.

 PERFORM SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “IPDM E/R” using CONSULT.
Is display history of DTC B20DD CRNT?

YES

>> Replace IPDM E/R. Refer to 

PCS-40, "Removal and Installation"

.

NO

>> Refer to 

GI-44, "Intermittent Incident"

.

CONSULT Display

DTC Detection Condition

Possible Cause

IGN RELAY ON
[B20DD]

The ignition relay ON is detected for 1 second at 
ignition switch OFF (CPU monitors the status at 
the contact and excitation coil circuits of the igni-
tion relay inside it).

IPDM E/R