Nissan Rogue. Manual - part 889

LAN

4WD BRANCH LINE CIRCUIT

LAN-255

< DTC/CIRCUIT DIAGNOSIS >

[CAN SYSTEM (TYPE 8)]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

4WD BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000011506838

1.

CHECK CONNECTOR

1. Turn the ignition switch OFF.

2. Disconnect the battery cable from the negative terminal.

3. Check the terminals and connectors of the AWD control unit for damage, bend and loose connection (unit

side and connector side).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS FOR OPEN CIRCUIT

1. Disconnect the connector of AWD control unit.

2. Check the resistance between the AWD control unit harness connector terminals.

Is the measurement value within the specification?

YES

>> GO TO 3.

NO

>> Repair the AWD control unit branch line.

3.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the AWD control unit. Refer to 

DLN-58, "Diagnosis Proce-

dure"

.

Is the inspection result normal?

YES (Present error)>>Replace the AWD control unit. Refer to 

DLN-68, "Removal and Installation"

.

YES (Past error)>>Error was detected in the AWD control unit branch line.

NG

>> Repair the power supply and the ground circuit.

AWD control unit harness connector

Resistance (

Ω)

Connector No.

Terminal No.

B75

8

16

Approx. 54 – 66

LAN-256

< DTC/CIRCUIT DIAGNOSIS >

[CAN SYSTEM (TYPE 8)]

PWBD BRANCH LINE CIRCUIT

PWBD BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000011506839

1.

CHECK CONNECTOR

1. Turn the ignition switch OFF.

2. Disconnect the battery cable from the negative terminal.

3. Check the terminals and connectors of the automatic back door control module for damage, bend and

loose connection (unit side and connector side).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS FOR OPEN CIRCUIT

1. Disconnect the connector of automatic back door control module.

2. Check the resistance between the automatic back door control module harness connector terminals.

Is the measurement value within the specification?

YES

>> GO TO 3.

NO

>> Repair the automatic back door control module branch line.

3.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the automatic back door control module. Refer to 

DLK-148,

"AUTOMATIC BACK DOOR CONTROL UNIT : Diagnosis Procedure"

.

Is the inspection result normal?

YES (Present error)>>Replace the automatic back door control module. Refer to 

DLK-283, "Removal and

Installation"

.

YES (Past error)>>Error was detected in the automatic back door control module branch line.

NG

>> Repair the power supply and the ground circuit.

Automatic back door control module harness connector

Resistance (

Ω)

Connector No.

Terminal No.

B55

24

12

Approx. 54 – 66

LAN

BCM BRANCH LINE CIRCUIT

LAN-257

< DTC/CIRCUIT DIAGNOSIS >

[CAN SYSTEM (TYPE 8)]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

BCM BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000011506840

1.

CHECK CONNECTOR

1. Turn the ignition switch OFF.

2. Disconnect the battery cable from the negative terminal.

3. Check the terminals and connectors of the BCM for damage, bend and loose connection (unit side and

connector side).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS FOR OPEN CIRCUIT

1. Disconnect the connector of BCM.

2. Check the resistance between the BCM harness connector terminals.

Is the measurement value within the specification?

YES

>> GO TO 3.

NO

>> Repair the BCM branch line.

3.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the BCM. Refer to the following.

• With intelligent key system: 

BCS-68, "Diagnosis Procedure"

.

• Without intelligent key system: 

BCS-128, "Diagnosis Procedure"

.

Is the inspection result normal?

YES (Present error)>>Replace the BCM. Refer to the following.

• With intelligent key system: 

BCS-75, "Removal and Installation"

.

• Without intelligent key system: 

BCS-135, "Removal and Installation"

.

YES (Past error)>>Error was detected in the BCM branch line.

NO

>> Repair the power supply and the ground circuit.

BCM harness connector

Resistance (

Ω)

Connector No.

Terminal No.

B16

60

80

Approx. 108 – 132

LAN-258

< DTC/CIRCUIT DIAGNOSIS >

[CAN SYSTEM (TYPE 8)]

AV BRANCH LINE CIRCUIT

AV BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000011506841

1.

CHECK CONNECTOR

1. Turn the ignition switch OFF.

2. Disconnect the battery cable from the negative terminal.

3. Check the following terminals and connectors for damage, bend and loose connection (unit side and con-

nector side).

-

AV control unit

-

BCM

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

1. Disconnect the connector of BCM.

2. Check the continuity between the BCM harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Check the harness and repair the root cause (CAN communication circuit 2 side). Refer to 

LAN-

265, "Diagnosis Procedure"

.

3.

CHECK HARNESS FOR OPEN CIRCUIT

1. Disconnect the connector of AV control unit.

2. Check the resistance between the AV control unit harness connector terminals.

-

Models with BOSE audio system

-

Models without BOSE audio system

Is the measurement value within the specification?

YES

>> GO TO 4.

NO

>> Repair the AV control unit branch line.

4.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the AV control unit. Refer to the following.

• Navigation with BOSE: 

AV-330, "AV CONTROL UNIT : Diagnosis Procedure"

• Navigation without BOSE: 

AV-172, "AV CONTROL UNIT : Diagnosis Procedure"

Is the inspection result normal?

YES (Present error)>>Replace the AV control unit. Refer to following.

• Navigation with BOSE: 

AV-369, "Removal and Installation"

• Navigation without BOSE: 

AV-200, "Removal and Installation"

YES (Past error)>>Error was detected in the AV control unit branch line.

NO

>> Repair the power supply and the ground circuit.

BCM harness connector

Continuity

Connector No.

Terminal No.

M18

6

8

Existed

5

9

Existed

AV control unit harness connector

Resistance (

Ω)

Connector No.

Terminal No.

M108

8

17

Approx. 54 – 66

AV control unit harness connector

Resistance (

Ω)

Connector No.

Terminal No.

M101

8

17

Approx. 54 – 66