Nissan Rogue. Manual - part 887

LAN

TCM BRANCH LINE CIRCUIT

LAN-247

< DTC/CIRCUIT DIAGNOSIS >

[CAN SYSTEM (TYPE 8)]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

TCM BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000011506831

1.

CHECK CONNECTOR

1. Turn the ignition switch OFF.

2. Disconnect the battery cable from the negative terminal.

3. Check the following terminals and connectors for damage, bend and loose connection (unit side and con-

nector side).

-

TCM

-

IPDM E/R

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

1. Disconnect the following harness connectors.

-

TCM

-

IPDM E/R

2. Check the continuity between the TCM harness connector and the IPDM E/R harness connector.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair the branch line between the TCM and IPDM E/R.

3.

CHECK IPDM E/R (OPEN CIRCUIT)

Check the continuity between the IPDM E/R terminals.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace the IPDM E/R.

4.

CHECK HARNESS FOR OPEN CIRCUIT

Check the resistance between the IPDM E/R harness connector terminals.

Is the measurement value within the specification?

YES

>> GO TO 5.

NO

>> Repair the IPDM E/R branch line.

5.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the TCM. Refer to 

TM-175, "Diagnosis Procedure"

.

Is the inspection result normal?

YES (Present error)>>Replace the TCM. Refer to 

TM-202, "Removal and Installation"

.

TCM harness connector

IPDM E/R harness connector

Continuity

Connector No.

Terminal No.

Connector No.

Terminal No.

F75

33

F42

87

Existed

23

88

Existed

IPDM E/R terminals

Continuity

Terminal No.

Terminal No.

87

39

Existed

88

40

Existed

IPDM E/R harness connector

Resistance (

Ω)

Connector No.

Terminal No.

E120

39

40

Approx. 54 – 66

LAN-248

< DTC/CIRCUIT DIAGNOSIS >

[CAN SYSTEM (TYPE 8)]

TCM BRANCH LINE CIRCUIT

YES (Past error)>>Error was detected in the TCM branch line.

NO

>> Repair the power supply and the ground circuit.

LAN

DLC BRANCH LINE CIRCUIT

LAN-249

< DTC/CIRCUIT DIAGNOSIS >

[CAN SYSTEM (TYPE 8)]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

DLC BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000011506832

1.

CHECK CONNECTOR

1. Turn the ignition switch OFF.

2. Disconnect the battery cable from the negative terminal.

3. Check the terminals and connectors of the data link connector for damage, bend and loose connection

(connector side and harness side).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS FOR OPEN CIRCUIT

Check the resistance between the data link connector terminals.

Is the measurement value within the specification?

YES (Present error)>>Check CAN system type decision again.

YES (Past error)>>Error was detected in the data link connector branch line circuit.

NO

>> Repair the data link connector branch line.

Data link connector

Resistance (

Ω)

Connector No.

Terminal No.

M22

6

14

Approx. 54 – 66

LAN-250

< DTC/CIRCUIT DIAGNOSIS >

[CAN SYSTEM (TYPE 8)]

M&A BRANCH LINE CIRCUIT

M&A BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000011506833

1.

CHECK CONNECTOR

1. Turn the ignition switch OFF.

2. Disconnect the battery cable from the negative terminal.

3. Check the terminals and connectors of the combination meter for damage, bend and loose connection

(unit side and connector side).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS FOR OPEN CIRCUIT

1. Disconnect the connector of combination meter.

2. Check the resistance between the combination meter harness connector terminals.

Is the measurement value within the specification?

YES

>> GO TO 3.

NO

>> Repair the combination meter branch line.

3.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the combination meter. Refer to  

MWI-60, "COMBINATION

METER : Diagnosis Procedure"

.

Is the inspection result normal?

YES (Present error)>>Replace the combination meter. Refer to  

MWI-84, "Removal and Installation"

.

YES (Past error)>>Error was detected in the combination meter branch line.

NO

>> Repair the power supply and the ground circuit.

Combination meter harness connector

Resistance (

Ω)

Connector No.

Terminal No.

M77

41

42

Approx. 54 – 66