Nissan Rogue. Manual - part 841

LAN

BCM BRANCH LINE CIRCUIT

LAN-63

< DTC/CIRCUIT DIAGNOSIS >

[CAN]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

BCM BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000011277542

1.

CHECK CONNECTOR

1. Turn the ignition switch OFF.

2. Disconnect the battery cable from the negative terminal.

3. Check the terminals and connectors of the BCM for damage, bend and loose connection (unit side and

connector side).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS FOR OPEN CIRCUIT

1. Disconnect the connector of BCM.

2. Check the resistance between the BCM harness connector terminals.

Is the measurement value within the specification?

YES

>> GO TO 3.

NO

>> Repair the BCM branch line.

3.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the BCM. Refer to the following.

• With intelligent key system: 

BCS-68, "Diagnosis Procedure"

.

• Without intelligent key system: 

BCS-128, "Diagnosis Procedure"

.

Is the inspection result normal?

YES (Present error)>>Replace the BCM. Refer to the following.

• With intelligent key system: 

BCS-75, "Removal and Installation"

.

• Without intelligent key system: 

BCS-135, "Removal and Installation"

.

YES (Past error)>>Error was detected in the BCM branch line.

NO

>> Repair the power supply and the ground circuit.

BCM harness connector

Resistance (

Ω)

Connector No.

Terminal No.

B16

60

80

Approx. 108 – 132

LAN-64

< DTC/CIRCUIT DIAGNOSIS >

[CAN]

AV BRANCH LINE CIRCUIT

AV BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000011277543

1.

CHECK CONNECTOR

1. Turn the ignition switch OFF.

2. Disconnect the battery cable from the negative terminal.

3. Check the following terminals and connectors for damage, bend and loose connection (unit side and con-

nector side).

-

AV control unit

-

BCM

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

1. Disconnect the connector of BCM.

2. Check the continuity between the BCM harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Check the harness and repair the root cause (CAN communication circuit 2 side). Refer to 

LAN-

71, "Diagnosis Procedure"

.

3.

CHECK HARNESS FOR OPEN CIRCUIT

1. Disconnect the connector of AV control unit.

2. Check the resistance between the AV control unit harness connector terminals.

-

Models with BOSE audio system

-

Models without BOSE audio system

Is the measurement value within the specification?

YES

>> GO TO 4.

NO

>> Repair the AV control unit branch line.

4.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the AV control unit. Refer to the following.

• Navigation with BOSE: 

AV-330, "AV CONTROL UNIT : Diagnosis Procedure"

• Navigation without BOSE: 

AV-172, "AV CONTROL UNIT : Diagnosis Procedure"

Is the inspection result normal?

YES (Present error)>>Replace the AV control unit. Refer to following.

• Navigation with BOSE: 

AV-369, "Removal and Installation"

• Navigation without BOSE: 

AV-200, "Removal and Installation"

YES (Past error)>>Error was detected in the AV control unit branch line.

NO

>> Repair the power supply and the ground circuit.

BCM harness connector

Continuity

Connector No.

Terminal No.

M18

6

8

Existed

5

9

Existed

AV control unit harness connector

Resistance (

Ω)

Connector No.

Terminal No.

M108

8

17

Approx. 54 – 66

AV control unit harness connector

Resistance (

Ω)

Connector No.

Terminal No.

M101

8

17

Approx. 54 – 66

LAN

AVM BRANCH LINE CIRCUIT

LAN-65

< DTC/CIRCUIT DIAGNOSIS >

[CAN]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

AVM BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000011277544

1.

CHECK CONNECTOR

1. Turn the ignition switch OFF.

2. Disconnect the battery cable from the negative terminal.

3. Check the following terminals and connectors for damage, bend and loose connection (unit side and con-

nector side).

-

Around view monitor control unit

-

BCM

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

1. Disconnect the connector of BCM.

2. Check the continuity between the BCM harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Check the harness and repair the root cause (CAN communication circuit 2 side). Refer to 

LAN-

71, "Diagnosis Procedure"

.

3.

CHECK HARNESS FOR OPEN CIRCUIT

1. Disconnect the connector of around view monitor control unit.

2. Check the resistance between the around view monitor control unit harness connector terminals.

-

With lane departure prevention system

-

Without lane departure prevention system

Is the measurement value within the specification?

YES

>> GO TO 4.

NO

>> Repair the around view monitor control unit branch line.

4.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the around view monitor control unit. Refer to the following.

• Navigation with BOSE: 

AV-331, "AROUND VIEW MONITOR CONTROL UNIT : Diagnosis Procedure"

• Navigation without BOSE: 

AV-172, "AROUND VIEW MONITOR CONTROL UNIT : Diagnosis Procedure"

Is the inspection result normal?

YES (Present error)>>Replace the around view monitor control unit. Refer to the following.

• Navigation with BOSE: 

AV-380, "Removal and Installation"

• Navigation without BOSE: 

AV-208, "Removal and Installation"

YES (Past error)>>Error was detected in the around view monitor control unit branch line.

NO

>> Repair the power supply and the ground circuit.

BCM harness connector

Continuity

Connector No.

Terminal No.

M18

6

8

Existed

5

9

Existed

Around view monitor control unit harness connector

Resistance (

Ω)

Connector No.

Terminal No.

M113

27

28

Approx. 54 – 66

Around view monitor control unit harness connector

Resistance (

Ω)

Connector No.

Terminal No.

M103

12

10

Approx. 54 – 66

LAN-66

< DTC/CIRCUIT DIAGNOSIS >

[CAN]

HVAC BRANCH LINE CIRCUIT

HVAC BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000011277545

1.

CHECK CONNECTOR

1. Turn the ignition switch OFF.

2. Disconnect the battery cable from the negative terminal.

3. Check the following terminals and connectors for damage, bend and loose connection (unit side and con-

nector side).

-

A/C auto amp. (With auto A/C)

-

Harness connector M127 (With auto A/C)

-

Harness connector M125 (With auto A/C)

-

Front air control (Without auto A/C)

-

BCM

Is the inspection result normal?

YES

>> GO TO 2. (With auto A/C)

YES

>> GO TO 3. (Without auto A/C)

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

1. Disconnect the connector of BCM.

2. Check the continuity between the BCM harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Check the harness and repair the root cause (CAN communication circuit 2 side). Refer to 

LAN-

71, "Diagnosis Procedure"

.

3.

CHECK HARNESS FOR OPEN CIRCUIT

1. Connect the connector of BCM (With auto A/C).

2. Disconnect the connector of A/C auto amp. (With auto A/C) or front air control (Without auto A/C).

3. Check the resistance between the A/C auto amp. (With auto A/C) or front air control (Without auto A/C)

harness connector terminals.

-

With auto A/C

-

Without auto A/C

Is the measurement value within the specification?

YES

>> GO TO 4.

NO

>> Repair the A/C auto amp. (With auto A/C) or front air control (Without auto A/C) branch line.

4.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the A/C auto amp. (With auto A/C) or front air control (With-

out auto A/C). Refer to the following.

• Automatic air conditioning: 

HAC-56, "Diagnosis Procedure"

.

BCM harness connector

Continuity

Connector No.

Terminal No.

M18

6

8

Existed

5

9

Existed

A/C auto amp. harness connector

Resistance (

Ω)

Connector No.

Terminal No.

M54

11

31

Approx. 54 – 66

Front air control harness connector

Resistance (

Ω)

Connector No.

Terminal No.

M50

7

23

Approx. 54 – 66