Nissan Rogue. Manual - part 376

DLK-346

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

HORN FUNCTION

HORN FUNCTION

Component Function Check

INFOID:0000000011279120

1.

CHECK FUNCTION 1

1. Perform “SIREN” in “Active Test” of “THEFT ALM” of “BCM” using CONSULT.

2. Check the horn operation.

Is the operation normal?

YES

>> Inspection End.

NO

>> Go to 

HRN-3, "Wiring Diagram"

.

Component Inspection

INFOID:0000000011279121

1.

CHECK ANTI-THEFT HORN RELAY

1. Turn ignition switch OFF.

2. Disconnect anti-theft horn relay.

3. Check voltage between anti-theft horn relay E101 terminal 2 and ground under the following conditions:

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace anti-theft horn relay.

Test item

Description

HORN

ON

 Horn

Sounds (for 0.5 sec)

(+)

(

−)

Condition

Voltage (V)

(Approx.)

 Anti-theft horn relay

Terminal

2

Ground

12 V direct current supply between terminals 1 and 2

12

No current supply

0

2015 Rogue NAM

WARNING CHIME FUNCTION

DLK-347

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

WARNING CHIME FUNCTION

Description

INFOID:0000000011279122

Performs operation method guide and warning with buzzer.

Component Function Check

INFOID:0000000011279123

1.

CHECK FUNCTION

 With CONSULT

1. Check the operation with “BUZZER” in the “Active Test”.

2. Touch “IGN KEY WARN ALM”, “SEAT BELT WARN TEST”or “LIGHT WARN ALM”on screen.
Is the inspection result normal?

YES

>> Warning buzzer into combination meter is OK.

NO

>> Refer to 

DLK-347, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000011279124

1.

CHECK METER BUZZER CIRCUIT

Operate the hazard lights by turning ON the hazard warning switch.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace combination meter. Refer to 

MWI-84, "Removal and Installation"

.

2.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> Inspection End.

2015 Rogue NAM

DLK-348

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

HAZARD FUNCTION

HAZARD FUNCTION

Description

INFOID:0000000011279125

Perform answer-back for each operation with number of blinks.

Component Function Check

INFOID:0000000011279126

1.

CHECK FUNCTION

Check hazard warning lamp “FLASHER” in “Active Test”.
Is the inspection result normal?

YES

>> Hazard warning lamp circuit is OK.

NO

>> Refer to 

DLK-348, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000011279127

1.

CHECK HAZARD SWITCH CIRCUIT

Operate the hazard lights by turning ON the hazard warning switch.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace hazard warning switch circuit. Refer to 

EXL-125, "Removal and Installation"

.

2.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> Inspection End.

2015 Rogue NAM

THIS PAGE INTENTIONALLY LEFT BLANK

DLK-349

 >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

.

2015 Rogue NAM