Nissan Rogue. Manual - part 371

DLK-326

< BASIC INSPECTION >

[WITHOUT INTELLIGENT KEY SYSTEM]

INSPECTION AND ADJUSTMENT

INSPECTION AND ADJUSTMENT

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description

INFOID:0000000011279086

Perform the system initialization when replacing BCM, replacing keyfob or registering an additional keyfob.

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement

INFOID:0000000011279087

Refer to the CONSULT Immobilizer mode and follow the on-screen instructions.

2015 Rogue NAM

U1000 CAN COMM CIRCUIT

DLK-327

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

DTC/CIRCUIT DIAGNOSIS

U1000 CAN COMM CIRCUIT

Description

INFOID:0000000011378205

Refer to 

LAN-8, "System Description"

.

DTC Logic

INFOID:0000000011378206

DTC DETECTION LOGIC

NOTE:

U1000 can be set if a module harness was disconnected and reconnected, perhaps during a repair. Confirm

that there are actual CAN diagnostic symptoms and a present DTC by performing the Self Diagnostic Result

procedure.

Diagnosis Procedure

INFOID:0000000011378207

1.

 PERFORM SELF DIAGNOSTIC

1. Turn ignition switch ON and wait for 2 second or more.

2. Check “Self Diagnostic Result”.
Is “CAN COMM CIRCUIT” displayed?

YES

>> Perform CAN Diagnosis as described in DIAGNOSIS section of CONSULT Operation Manual.

NO

>> Refer to 

GI-44, "Intermittent Incident"

.

CONSULT Display

DTC Detection Condition

Possible cause

CAN COMM CIRCUIT
[U1000]

When any listed module cannot communicate with CAN 
communication signal continuously for 2 seconds or 
more with ignition switch ON.

In CAN communication system, any item (or items) 
of the following listed below is malfunctioning:
• Transmission
• Receiving (ECM)
• Receiving (VDC/TCS/ABS)
• Receiving (METER/M&A)
• Receiving (TCM)
• Receiving (IPDM E/R)

2015 Rogue NAM

DLK-328

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

U1010 CONTROL UNIT (CAN)

U1010 CONTROL UNIT (CAN)

DTC Logic

INFOID:0000000011378208

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000011378209

1.

 REPLACE BCM

When DTC U1010 is detected, replace BCM.

>> Replace BCM. Refer to 

BCS-135, "Removal and Installation"

.

CONSULT Display

DTC Detection Condition

Possible Cause

CAN COMM CIRCUIT
[U1010]

BCM detected internal CAN communication circuit mal-
function.

BCM

2015 Rogue NAM

POWER SUPPLY AND GROUND CIRCUIT

DLK-329

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

POWER SUPPLY AND GROUND CIRCUIT

BCM
BCM : Diagnosis Procedure

INFOID:0000000011378210

Regarding Wiring Diagram information, refer to 

BCS-110, "Wiring Diagram"

.

1.

 CHECK FUSE

Check that the following fuse is not blown.

Is the fuse blown?

YES

>> Replace the blown fuse after repairing the affected circuit.

NO

>> GO TO 2.

2.

 CHECK POWER SUPPLY CIRCUIT

1. Disconnect BCM connector M20.

2. Check voltage between BCM connector M20 and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness or connectors.

3.

 CHECK GROUND CIRCUIT

Check continuity between BCM connector M20 and ground.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Repair or replace harness or connectors.

Terminal No.

Signal name

Fuse No.

161

BCM power supply

7 (10A)

BCM

Ground

Voltage

(Approx.)

Connector

Terminal

M20

161

—

Battery voltage

BCM

Ground

Continuity

Connector

Terminal

M20

170

—

Yes

171

2015 Rogue NAM