Nissan Rogue. Manual - part 334

DLK-178

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

BACK DOOR REQUEST SWITCH

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK BACK DOOR REQUEST SWITCH

Refer to 

DLK-178, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace back door opener switch. Refer to 

DLK-285, "Removal and Installation"

.

5.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> Inspection End.

Component Inspection

INFOID:0000000011278898

1.

CHECK BACK DOOR REQUEST SWITCH

1. Turn ignition switch OFF.

2. Disconnect back door opener switch assembly connector.

3. Check continuity between back door opener switch assembly terminals.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace back door opener switch assembly. Refer to 

DLK-285, "Removal and Installation"

.

Back door opener switch 

Ground

Continuity 

Connector

Terminal

D509

3

Yes

 Back door opener switch assembly

Condition

Continuity 

Terminal

3

4

Back door request switch

Pressed

Yes

Released

No

2015 Rogue NAM

BACK DOOR OPENER SWITCH

DLK-179

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

BACK DOOR OPENER SWITCH

Component Function Check

INFOID:0000000011278899

1.

CHECK FUNCTION

1. Select “TRUNK” of “BCM” using CONSULT.

2. Select “TR/BD OPEN SW” in “Data Monitor”.

3. Check that the function operates normally according to the following conditions:

Is the inspection result normal?

YES

>> Back door opener switch is OK.

NO

>> Refer to 

DLK-179, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000011278900

Regarding Wiring Diagram information, refer to 

DLK-90, "Wiring Diagram"

.

1.

CHECK BACK DOOR OPEN INPUT SIGNAL

1. Turn ignition switch OFF.

2. Disconnect back door opener switch connector.

3. Check signal between back door opener switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK BACK DOOR OPENER SWITCH CIRCUIT

1. Disconnect BCM connector.

2. Check continuity between BCM harness connector and back door opener switch harness connector.

3. Check continuity between BCM harness connector and ground.

Monitor item

Condition

Status

TR/BD OPEN SW

Back door opener switch

Pressed

ON

Released

OFF

(+)

(–)

Signal

(Reference value)

Back door opener switch 

Connector

Terminal 

D507

1

Ground

JPMIA0012GB

BCM

Back door opener switch 

Continuity 

Connector

Terminal

Connector

Terminal

B16

56

D507

1

Yes

BCM

Ground

Continuity 

Connector

Terminal

B16

56

No

2015 Rogue NAM

DLK-180

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

BACK DOOR OPENER SWITCH

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-75, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK BACK DOOR OPENER SWITCH GROUND CIRCUIT

Check continuity between back door opener switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK BACK DOOR OPENER SWITCH

Refer to 

DLK-180, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace back door opener switch. Refer to 

DLK-285, "Removal and Installation"

.

5.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> Inspection End.

Component Inspection

INFOID:0000000011278901

1.

CHECK BACK DOOR OPENER SWITCH

1. Turn ignition switch OFF.

2. Disconnect back door opener switch connector.

3. Check continuity between back door opener switch terminals.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace back door opener switch. Refer to 

DLK-285, "Removal and Installation"

.

Back door opener switch 

Ground

Continuity 

Connector

Terminal

D507

2

Yes

Back door opener switch assembly

Condition

Continuity 

Terminal 

1

2

Back door opener 
switch

Pressed

Yes

Released

No

2015 Rogue NAM

INTELLIGENT KEY WARNING BUZZER

DLK-181

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

INTELLIGENT KEY WARNING BUZZER

Component Function Check

INFOID:0000000011278902

1.

CHECK FUNCTION

1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2. Select “OUTSIDE BUZZER” in “Active Test”.

3. Touch “On” or “Off” to check that it works normally.
Is the inspection result normal?

YES

>> Intelligent Key warning buzzer is OK.

NO

>> Refer to 

DLK-181, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000011278903

Regarding Wiring Diagram information, refer to 

DLK-73, "Wiring Diagram"

.

1.

CHECK INTELLIGENT KEY WARNING BUZZER CIRCUIT

1. Disconnect BCM connector.

2. Check continuity between BCM harness connector and Intelligent Key warning buzzer harness connector.

3. Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness.

2.

CHECK INTELLIGENT KEY WARNING BUZZER

Refer to 

DLK-181, "Component Inspection"

.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-75, "Removal and Installation"

.

NO

>> Replace Intelligent Key warning buzzer. Refer to 

DLK-280, "Removal and Installation"

.

Component Inspection

INFOID:0000000011278904

1.

CHECK INTELLIGENT KEY WARNING BUZZER

1. Turn ignition switch OFF.

2. Disconnect Intelligent Key warning buzzer connector.

3. Connect battery power supply directly to Intelligent Key warning buzzer terminals and check the opera-

tion.

Is the inspection result normal?

BCM

Intelligent Key warning buzzer

Continuity 

Connector

Terminal

Connector

Terminal

E29

132

E24

1

Yes

BCM

Ground

Continuity 

Connector

Terminal

E29

132

No

Intelligent Key warning buzzer

Operation

Terminal

(+)

(

−)

1

3

Buzzer sounds

2015 Rogue NAM