Nissan Rogue. Manual - part 322

DLK-130

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2422 BACK DOOR STATE

Is the difference between the 2 monitor items 10 or more?

YES

>> GO TO 4.

NO

>> Replace automatic back door control module. Refer to 

DLK-283, "Removal and Installation"

.

4.

CHECK ENCODER POWER SUPPLY

1. Turn ignition switch OFF.

2. Disconnect spindle unit connector.

3. Check voltage between spindle unit harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> GO TO 5.

5.

CHECK ENCODER CIRCUIT

1. Disconnect automatic back door control module connector.

2. Check continuity between automatic back door control module harness connector and spindle unit har-

ness connector.

3. Check continuity between automatic back door control module harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic back door control module. Refer to 

DLK-283, "Removal and Installation"

.

NO

>> Repair or replace harness.

6.

CHECK ENCODER CIRCUIT 2

1. Disconnect automatic back door control module connector.

2. Check continuity between automatic back door control module harness connector and spindle unit har-

ness connector.

Monitor item

Status

SPINDLE SENSOR LH

0 – 65535

SPINDLE SENSOR RH

0 – 65535

(+)

(–)

Voltage

(Approx.)

Spindle unit

Connector

Terminal

LH

B95

4

Ground

Battery voltage

RH

B73

Automatic back door control module

Spindle unit

Continuity 

 Connector

Terminal

 Connector

Terminal

B55

19

LH

B95

4

Yes

20

RH

B73

Automatic back door control module

Ground

Continuity 

 Connector

Terminal

B55

19

No

20

2015 Rogue NAM

B2422 BACK DOOR STATE

DLK-131

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

3. Check continuity between automatic back door control module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace harness.

7.

CHECK ENCODER CIRCUIT 3

1. Connect automatic back door control module and spindle unit connector

2. Check continuity between automatic back door control module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Replace automatic back door control module. Refer to 

DLK-283, "Removal and Installation"

.

8.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Replace automatic back door control module. Refer to 

DLK-283, "Removal and Installation"

.

NO

>> Repair or replace the malfunctioning parts.

Automatic back door control module

Spindle unit

Continuity 

 Connector

Terminal

 Connector

Terminal

B55

6

LH

B95

3

Yes

7

5

8

RH

B73

3

9

5

Automatic back door control module

Ground

Continuity 

 Connector

Terminal

B55

6

No

7

8

9

Automatic back door control module

Ground

Voltage

(Approx.)

 Connector

Terminal

B55

21

0 V

2015 Rogue NAM

DLK-132

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2423 AUTOMATIC BACK DOOR MOTOR OPERATION TIME

B2423 AUTOMATIC BACK DOOR MOTOR OPERATION TIME

DTC Logic

INFOID:0000000011278842

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON. 

2. Operate automatic back door.

3. Check “Self Diagnostic Result” of “AUTO BACK DOOR” using CONSULT.
Is DTC detected?

YES

>> Refer to 

DLK-132, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011278843

Regarding Wiring Diagram information, refer to 

DLK-90, "Wiring Diagram"

.

1.

ERASE DTC

1. At least 180 seconds are passed after automatic back door operation is inhibited.

2. Erase DTC, and then repeat “PERFORM DTC CONFIRMATION PROCEDURE”.
Is DTC detected?

YES

>> GO TO 2.

NO

>> Inspection End.

2.

CHECK SPINDLE MOTOR CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect automatic back door control module and spindle unit connector.

3. Check continuity between automatic back door control module harness connector and spindle unit har-

ness connector.

4. Check continuity between automatic back door control module harness connector and ground.

DTC

CONSULT display de-

scription

DTC detecting condition

Possible cause

B2423

ABD MTR TIME OUT

When the automatic back door control module and 
spindle motor operate in the same direction for 180 
seconds or more continuously.

• Spindle motor
• Automatic back door control 

module

• Harness or connector

Automatic back door control module

Spindle unit

Continuity 

 Connector

Terminal

 Connector

Terminal

B56

27

LH

B95

1

Yes

34

7

29

RH

B73

1

36

7

2015 Rogue NAM

B2423 AUTOMATIC BACK DOOR MOTOR OPERATION TIME

DLK-133

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

Is the inspection result normal?

YES

>> Replace automatic back door control module. Refer to 

DLK-283, "Removal and Installation"

.

NO

>> Repair or replace harness.

Automatic back door control module

Ground

Continuity 

 Connector

Terminal

B56

27

No

29

34

36

2015 Rogue NAM