Nissan Rogue. Manual - part 177

BRAKE WARNING LAMP

BRC-119

< DTC/CIRCUIT DIAGNOSIS >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

3. Check that data monitor displays “On” for 1 second after ignition switch is turned ON and then changes to

“Off”.

CAUTION:

Never start the engine.

Is the inspection result normal?

YES

>> Replace the combination meter. Refer to 

MWI-84, "Removal and Installation"

.

NO

>> Replace the ABS actuator and electric unit (control unit). Refer to 

BRC-134, "Removal and Instal-

lation"

.

BRC-120

< DTC/CIRCUIT DIAGNOSIS >

[VDC/TCS/ABS]

VDC WARNING LAMP

VDC WARNING LAMP

Component Function Check

INFOID:0000000011280653

1.

CHECK VDC WARNING LAMP FUNCTION

Check that VDC warning lamp in combination meter turns ON for 1 second after ignition switch is turned ON.

CAUTION:

Never start the engine.
Is the inspection result normal?

YES

>> Inspection End.

NO

>> Proceed to 

BRC-120, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000011280654

1.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-

CUIT
Perform the trouble diagnosis for ABS actuator and electric unit (control unit) power supply and ground circuit.

Refer to 

BRC-120, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace error-detected parts.

2.

PERFORM THE SELF DIAGNOSTIC

With CONSULT

1. Turn the ignition switch OFF 

→ ON.

CAUTION:

• Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

• Start the engine.

2. Repeat step 1 two or more times.

3. Perform “Self Diagnostic Result” of “ABS”.
Is any DTC detected?

YES

>> Check the DTC. Refer to 

BRC-53, "DTC Index"

.

NO

>> GO TO 3.

3.

CHECK VDC WARNING LAMP SIGNAL

With CONSULT

1. Select “ABS”, “Data Monitor” and “SLIP/VDC LAMP” according to this order.

2. Turn the ignition switch OFF.

3. Check that data monitor displays “On” for approx. 1 second after ignition switch is turned ON, and then

changes to “Off”.

CAUTION:

Never start the engine.

Is the inspection result normal?

YES

>> Replace the combination meter. Refer to 

MWI-84, "Removal and Installation"

.

NO

>> Replace the ABS actuator and electric unit (control unit). Refer to 

BRC-134, "Removal and Instal-

lation"

.

VDC OFF INDICATOR LAMP

BRC-121

< DTC/CIRCUIT DIAGNOSIS >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

VDC OFF INDICATOR LAMP

Component Function Check

INFOID:0000000011280655

1.

CHECK VDC OFF INDICATOR LAMP FUNCTION (1)

Check that VDC OFF indicator lamp in combination meter turns ON for 1 second after ignition switch is turned

ON.

CAUTION:

Never start the engine.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Proceed to 

BRC-121, "Diagnosis Procedure"

.

2.

CHECK VDC OFF INDICATOR LAMP FUNCTION (2)

Check that VDC OFF indicator lamp in combination meter turns ON/OFF when VDC OFF switch is operated.
Is the inspection result normal?

YES

>> Inspection End.

NO

>> Check the VDC OFF switch system. Refer to 

BRC-115, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000011280656

1.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-

CUIT

Perform the trouble diagnosis for ABS actuator and electric unit (control unit) power supply and ground circuit.

Refer to 

BRC-121, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace error-detected parts.

2.

CHECK VDC OFF INDICATOR LAMP SIGNAL

With CONSULT

1. Select “ABS”, “Data Monitor” and “OFF LAMP” according to this order.

2. Turn the ignition switch OFF.

3. Check that data monitor displays “On” for 1 second after ignition switch is turned ON, and then changes to

“Off”.

CAUTION:

Never start the engine.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace the ABS actuator and electric unit (control unit). Refer to 

BRC-134, "Removal and Instal-

lation"

.

3.

CHECK VDC OFF INDICATOR LAMP SIGNAL

With CONSULT

1. Select “ABS”, “Data Monitor” and “OFF LAMP” according to this order.

2. Check that data monitor displays “On” or “Off” each time when VDC OFF switch is operated.
Is the inspection result normal?

YES

>> Replace the combination meter. Refer to 

MWI-84, "Removal and Installation"

.

NO

>> Check the VDC OFF switch system. Refer to 

BRC-115, "Diagnosis Procedure"

.

BRC-122

< SYMPTOM DIAGNOSIS >

[VDC/TCS/ABS]

EXCESSIVE OPERATION FREQUENCY

SYMPTOM DIAGNOSIS

EXCESSIVE OPERATION FREQUENCY

Description

INFOID:0000000011280657

VDC function, TCS function, ABS function, EBD function, Brake limited slip differential (BLSD) function, Brake

assist function, hill start assist function or Brake force distribution function operates in excessive operation fre-

quency.

Diagnosis Procedure

INFOID:0000000011280658

1.

CHECK BRAKING FORCE

Check brake force using a brake tester.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check brake system.

2.

CHECK FRONT AND REAR AXLE

Check that there is no excessive looseness in front and rear axle.

• 2WD: Refer to 

FAX-7, "Inspection"

 (front) or 

RAX-6, "Inspection"

 (rear).

• AWD: Refer to 

FAX-45, "Inspection"

 (front) or 

RAX-14, "Inspection"

 (rear).

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace error-detected parts.

3.

CHECK WHEEL SENSOR

Check wheel sensor.

• Check installation and damage of wheel sensor.

• Check connection of wheel sensor harness connector.

• Check terminal of wheel sensor harness connector.
Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair installation or replace wheel sensor.

• Front wheel sensor: Refer to 

BRC-130, "FRONT WHEEL SENSOR : Removal and Installation"

.

• Rear wheel sensor: Refer to 

BRC-132, "REAR WHEEL SENSOR : Removal and Installation"

.

4.

CHECK SENSOR ROTOR

Check that there is no looseness, damage or foreign material on sensor rotor.
Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair installation or replace sensor rotor.

• Front sensor rotor: Refer to 

BRC-133, "FRONT SENSOR ROTOR : Removal and Installation -

Front Sensor Rotor"

.

• Rear sensor rotor: Refer to 

BRC-133, "REAR SENSOR ROTOR : Removal and Installation -

Rear Sensor Rotor"

.

5.

CHECK WARNING LAMP TURNS OFF

Check that ABS warning lamp, brake warning lamp and VDC warning lamp turn OFF approx. 1 second after

key switch is turned ON and stay in OFF status during driving.

CAUTION:

Brake warning lamp turns ON when parking brake is operated (parking brake switch is ON) or brake

fluid is less than the specified level (brake fluid level switch is ON).
Is the inspection result normal?

YES

>> Normal

NO

>> GO TO 6.

6.

PERFORM THE SELF DIAGNOSTIC