Nissan Rogue. Manual - part 174

C1199 BRAKE BOOSTER

BRC-107

< DTC/CIRCUIT DIAGNOSIS >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

C1199 BRAKE BOOSTER

DTC Logic

INFOID:0000000011280635

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF DIAGNOSTIC RESULT

 With 

CONSULT.

1. Turn the ignition switch ON.

2. Perform “Self Diagnostic Result”.
Is DTC C1199 detected?

YES

>> Proceed to diagnosis procedure. Refer to 

BRC-107, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011280636

Regarding Wiring Diagram information, refer to 

BRC-55, "Wiring Diagram"

.

1.

CHECK BRAKE BOOSTER

1. Turn the ignition switch OFF.

2. Check brake booster. Refer to 

BR-10, "Inspection"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace brake booster. Refer to 

BR-31, "Removal and installation"

.

2.

CHECK VACUUM PIPING

Check vacuum piping. Refer to 

BR-33, "Exploded View"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace vacuum piping. Refer to 

BR-33, "Removal and Installation"

.

3.

CHECK VACUUM SENSOR CIRCUIT

1. Disconnect vacuum sensor harness connector.

2. Disconnect ABS actuator and electric unit (control unit) harness connector.

3. Check continuity between vacuum sensor harness connector and ABS actuator and electric unit (control

unit) harness connector.

4. Check continuity between vacuum sensor harness connector and ground.

DTC

Display Item

Malfunction detected condition

Possible causes

C1199

BRAKE BOOSTER

When brake booster vacuum is approx. 0 kPa (0 mm-
Hg) during engine running.

• Harness or connector
• Vacuum sensor (brake booster)
• Vacuum piping
• ABS actuator and electric unit 

(control unit)

Vacuum sensor

ABS actuator and electric unit (control unit)

Continuity

Connector

Terminal

Connector

Terminal

E167

1

E125

12

Yes

2

24

3

5

BRC-108

< DTC/CIRCUIT DIAGNOSIS >

[VDC/TCS/ABS]

C1199 BRAKE BOOSTER

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace malfunctioning components.

4.

CHECK TERMINAL

• Check vacuum sensor pin terminals for damage or loose connection with harness connector.

• Check ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with har-

ness connector.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace malfunctioning components.

5.

REPLACE VACUUM SENSOR

With CONSULT

1. Connect ABS actuator and electric unit (control unit) harness connector.

2. Replace vacuum sensor. Refer to 

BR-31, "Exploded View"

.

CAUTION:

Always replace brake booster because vacuum sensor cannot be disassembled.

3. Erase “Self Diagnostic Result” of “ABS”.

4. Turn the ignition switch OFF.

5. Start engine.

6. Perform “Self Diagnostic Result” of “ABS”.
Is DTC “C1199” detected?

YES

>> Replace ABS actuator and electric unit (control unit). Refer to 

BRC-134, "Removal and Installa-

tion"

.

NO

>> Inspection End.

Vacuum sensor

—

Continuity

Connector

Terminal

E167

1

Ground

No

2

3

C119A VACUUM SENSOR

BRC-109

< DTC/CIRCUIT DIAGNOSIS >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

C119A VACUUM SENSOR

DTC Logic

INFOID:0000000011280637

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF DIAGNOSTIC RESULT

 With 

CONSULT.

1. Turn the ignition switch ON.

2. Perform “Self Diagnostic Result”.
Is DTC C119A detected?

YES

>> Proceed to diagnosis procedure. Refer to 

BRC-109, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011280638

Regarding Wiring Diagram information, refer to 

BRC-55, "Wiring Diagram"

.

1.

CHECK VACUUM SENSOR POWER SUPPLY

1. Turn the ignition switch OFF.

2. Disconnect vacuum sensor harness connector.

3. Check voltage between vacuum sensor harness connector and ground.

4. Turn the ignition switch ON.

CAUTION:

Never start engine.

5. Check voltage between vacuum sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK VACUUM SENSOR POWER SUPPLY CIRCUIT

1. Turn the ignition switch OFF.

2. Disconnect ABS actuator and electric unit (control unit) harness connector.

3. Check continuity between vacuum sensor harness connector and ABS actuator and electric unit (control

unit) harness connector.

DTC

Display Item

Malfunction detected condition

Possible causes

C119A

VACUUM SEN VOLT

When a malfunction is detected in supply power volt-
age of vacuum sensor.

• Harness or connector
• Vacuum sensor (brake booster)
• ABS actuator and electric unit 

(control unit)

Vacuum sensor

—

Voltage

(Approx.)

Connector

Terminal

E167

3

Ground

0 V

Vacuum sensor

—

Voltage

(Approx.)

Connector

Terminal

E167

3

Ground

4.75 V – 5.25 V

BRC-110

< DTC/CIRCUIT DIAGNOSIS >

[VDC/TCS/ABS]

C119A VACUUM SENSOR

4. Check continuity between vacuum sensor harness connector and ground.

Is the inspection result normal?

YES

>> Perform diagnosis of ABS actuator and electric unit (control unit) power supply and ground circuit.

Refer to 

BRC-109, "Diagnosis Procedure"

.

NO

>> Repair or replace malfunctioning components.

3.

CHECK VACUUM SENSOR GROUND CIRCUIT

1. Turn the ignition switch OFF.

2. Check continuity between vacuum sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace malfunctioning components.

4.

CHECK TERMINAL

• Check vacuum sensor pin terminals for damage or loose connection with harness connector.

• Check ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with har-

ness connector.

Is the inspection result normal?

YES

>> Replace ABS actuator and electric unit (control unit). Refer to 

BRC-134, "Removal and Installa-

tion"

.

NO

>> Repair or replace malfunctioning components.

Vacuum sensor

ABS actuator and electric unit (control unit)

Continuity

Connector

Terminal

Connector

Terminal

E167

3

E125

5

Yes

Vacuum sensor

—

Continuity

Connector

Terminal

E167

3

Ground

No

Vacuum sensor

—

Continuity

Connector

Terminal

E167

2

Ground

Yes