Nissan Rogue. Manual - part 1202

TM-180

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

O/D OFF INDICATOR LAMP

O/D OFF INDICATOR LAMP

Component Function Check

INFOID:0000000011279399

1.

CHECK O/D OFF INDICATOR LAMP FUNCTION

Check O/D OFF indicator lamp turns ON for approx. 2 seconds when ignition switch turns ON.
Is the inspection results normal?

YES

>> INSPECTION END

NO

>> Go to 

TM-180, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000011279400

1.

CHECK DTC (TCM)

With CONSULT

1. Turn ignition switch ON.

2. Check “Self Diagnostic Results” in “TRANSMISSION”.
Is any DTC detected?

YES

>> Check DTC detected item. Refer to 

TM-63, "DTC Index"

.

NO

>> GO TO 2.

2.

CHECK DTC (COMBINATION METER)

With CONSULT

Check “Self Diagnostic Results” in “METER/M&A”.
Is any DTC detected?

YES

>> Check DTC detected item. Refer to 

MWI-31, "DTC Index"

.

NO

>> GO TO 3.

3.

CHECK COMBINATION METER INPUT/OUTPUT SIGNAL

With CONSULT

1. Shift the selector lever to “D” position.

2. Select “Data Monitor” in “METER/M&A”.

3. Select “O/D OFF IND”.

4. Check that “O/D OFF IND” turns ON/OFF when overdrive control switch is operated. Refer to 

MWI-25,

"Reference Value"

.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-84, "Removal and Installation"

.

NO

>> GO TO 4.

4.

CHECK TCM INPUT/OUTPUT SIGNAL

With CONSULT

1. Select “Data Monitor” in “TRANSMISSION”.

2. Select “SPORT MODE SW”.

3. Check that “SPORT MODE SW” turns ON/OFF when overdrive control switch is operated. Refer to 

TM-

52, "Reference Value"

.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-84, "Removal and Installation"

.

NO

>> Check overdrive control switch circuit. Refer to 

TM-177, "Diagnosis Procedure"

.

SHIFT POSITION INDICATOR CIRCUIT

TM-181

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

SHIFT POSITION INDICATOR CIRCUIT

Component Parts Function Inspection

INFOID:0000000011279401

1.

CHECK SHIFT POSITION INDICATOR

1. Start the engine.

2. Shift selector lever.

3. Check that the selector lever position and the shift position indicator on the combination meter are identi-

cal.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Go to 

TM-181, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000011279402

1.

CHECK TCM INPUT/OUTPUT SIGNAL 

With CONSULT

1. Start the engine.

2. Select “Data Monitor” in “TRANSMISSION”.

3. Select “RANGE”. 

4. Shift selector lever.

5. Check that selector lever position, “RANGE” on CONSULT screen, and shift position indicator display on

combination meter are identical.

Is the check result normal?

YES

>> INSPECTION END

NO-1 (“RANGE” is changed but is not displayed on shift position indicator.>>Check “Self Diagnostic Result”

in “TRANSMISSION”.

NO-2 (“RANGE” and shift position indicator are different.)>>Check “Self Diagnostic Result” in “TRANSMIS-

SION”.

NO-3 (Specific “RANGE” is not displayed on shift position indicator.)>>Check “Self Diagnostic Result” in

“METER/M&A”.

TM-182

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

SHIFT LOCK SYSTEM

SHIFT LOCK SYSTEM

Component Function Check

INFOID:0000000011279403

1.

CHECK SHIFT LOCK OPERATION (PART 1)

1. Turn ignition ON.

2. Shift the selector lever to “P” position.

3. Attempt to shift the selector lever to any other than position with the brake pedal released.
Can the selector lever be shifted to any other position?

YES

>> Go to 

TM-182, "Diagnosis Procedure"

.

NO

>> GO TO 2.

2.

CHECK SHIFT LOCK OPERATION (PART 2)

Attempt to shift the selector lever to any other than position with the brake pedal depressed.
Can the selector lever be shifted to any other position?

YES

>> Inspection End.

NO

>> Go to 

TM-182, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000011279404

Regarding Wiring Diagram information, refer to 

TM-75, "Wiring Diagram"

.

1.

CHECK STOP LAMP SWITCH

1. Ignition switch ON.

2. Check voltage between stop lamp switch connector E38 terminal 4 and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 3.

2.

CHECK GROUND CIRCUIT

1. Ignition switch OFF.

2. Disconnect CVT shift selector connector.

3. Check continuity between CVT shift selector connector M107 terminal 4 and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

3.

CHECK STOP LAMP SWITCH POWER CIRCUIT

Check voltage between stop lamp switch connector E38 terminal 3 and ground.

Stop lamp switch

Ground

Brake pedal

Voltage

Connector

Terminal

E38

4

Ground

Applied

Battery voltage

Released

0V

CVT shift selector

Ground

Continuity

Connector

Terminal

M107

4

Ground

Yes

SHIFT LOCK SYSTEM

TM-183

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the inspection result normal?

YES

>> Replace stop lamp switch. Refer to 

BR-20, "Exploded View"

.

NO

>> Repair or replace harness.

4.

CHECK CVT SHIFT SELECTOR POWER CIRCUIT

Check voltage between CVT shift selector connector M107 terminal 3 and ground.

Is the inspection result normal?

YES

>> Replace CVT shift selector. Refer to 

TM-193, "Removal and Installation"

.

NO

>> Repair or replace harness or connector.

Component Inspection (CVT Shift Selector Assembly)

INFOID:0000000011279405

1.

CHECK CVT SHIFT SELECTOR ASSEMBLY (PART 1)

Check continuity between CVT shift selector connector terminals.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace CVT shift selector assembly. Refer to 

TM-193, "Removal and Installation"

.

2.

CHECK CVT SHIFT SELECTOR ASSEMBLY (PART 2)

Apply voltage to terminals of CVT shift selector and check that shift lock solenoid is activated.

CAUTION:

• Connect the fuse between the terminals when applying the voltage.

• Never cause shorting between terminals.

Is the inspection result normal?

YES

>> Inspection End

NO

>> Replace CVT shift selector assembly. Refer to 

TM-193, "Removal and Installation"

.

Component Inspection (Stop Lamp Switch)

INFOID:0000000011279406

1.

CHECK STOP LAMP SWITCH

Check continuity between the stop lamp switch connector terminals.

Stop lamp switch

Ground

Voltage

Connector

Terminal

E38

3

Ground

Battery voltage

CVT shift selector

Ground

Brake pedal

Voltage

Connector

Terminal

M107

3

Ground

Applied

Battery voltage

CVT shift selector

Condition

Continuity

Terminal

3 – 4

Shift the selector lever to “P” position.

Yes

Other than the above.

No

+ (fuse)

-

Condition

Status

Shift lock solenoid

Terminal

3

4

• Selector lever: “P” position
• Apply 12 V between terminals 3 and 4.

Shift lock solenoid operates