Nissan Rogue. Manual - part 1077

B2602 SHIFT POSITION

SEC-87

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B2602 SHIFT POSITION

DTC Logic

INFOID:0000000011278493

DTC DETECTION LOGIC

NOTE:

• If DTC B2602 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-64, "DTC Logic"

.

• If DTC B2602 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-65, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Start engine.

2. Drive vehicle at a speed of 4 km/h (2.5 MPH) or more for 10 seconds or more.

3. Check DTC in “Self Diagnostic Result” of “BCM” using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-87, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011278494

Regarding Wiring Diagram information, refer to 

SEC-28, "Wiring Diagram"

.

1.

CHECK CVT SHIFT SELECTOR SWITCH FUNCTION

1. Turn ignition switch ON.

2. Select “DETE/CANCEL SW” and “VEH SPEED 1” in “Data Monitor” with CONSULT.

3. Check “DETE/CANCEL SW” and “VEH SPEED 1” indication under the following conditions:

Is the inspection result normal?

YES

>> Refer to 

GI-44, "Intermittent Incident"

.

NO-1 >> If “DETE/CANCEL SW” is incorrect. GO TO 4.

NO-2 >> If “VEH SPEED 1” is incorrect. GO TO 2. 

2.

CHECK DTC OF COMBINATION METER

Check DTC in “Self Diagnostic Result” of “METER/M&A” using CONSULT.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B2602

SHIFT POSITION

BCM detects the following status for 10 seconds.
• Selector lever is in the P (Park) position
• Vehicle speed is 4 km/h (2.5 MPH) or more
• Ignition switch is in the ON position

• Harness or connectors

(CAN communication line is open or 
shorted.)

• Harness or connectors

[CVT shift selector (park position 
switch) circuit is open or shorted.]

• CVT shift selector (park position 

switch)

• Combination meter
• BCM

Monitor item

Condition

Indication

DETE/CANCEL SW

CVT Shift selector

In any position other than P (Park)

OFF

 P (Park)

ON

VEH SPEED 1

Vehicle not moving

0

Vehicle moving

Varies

2015 Rogue NAM

SEC-88

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2602 SHIFT POSITION

Is DTC detected?

YES

>> Perform the trouble diagnosis related to the detected DTC. Refer to 

MWI-31, "DTC Index"

.

NO

>> GO TO 3.

3.

CHECK DTC OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

Check DTC in “Self Diagnostic Result” of “ABS” using CONSULT.
Is DTC detected?

YES

>> Perform the trouble diagnosis related to the detected DTC. Refer to 

BRC-53, "DTC Index"

.

NO

>> GO TO 6.

4.

CHECK CVT SHIFT SELECTOR CIRCUIT

1. Disconnect BCM connector and CVT shift selector connector.

2. Check continuity between CVT shift selector (park position switch) harness connector and BCM harness

connector.

3. Check continuity between CVT shift selector (park position switch) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace harness.

5.

CHECK CVT SHIFT SELECTOR CIRCUIT

1. Disconnect BCM connector and CVT shift selector connector.

2. Check continuity between CVT shift selector (park position switch) harness connector and BCM harness

connector.

3. Check continuity between CVT shift selector (park position switch) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness.

6.

CHECK CVT SHIFT SELECTOR (PARK POSITION SWITCH)

Refer to 

SEC-89, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Replace CVT shift selector. Refer to 

TM-193, "Removal and Installation"

.

7.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> Inspection End.

CVT shift selector (park position switch)

BCM

Continuity

Connector

Terminal

Connector

Terminal

M107

13

M19

94

Yes

CVT shift selector (park position switch)

Ground

Continuity

Connector

Terminal

M107

13

No

CVT shift selector (park position switch)

BCM

Continuity

Connector

Terminal

Connector

Terminal

M107

12

M18

17

Yes

CVT shift selector (park position switch)

Ground

Continuity

Connector

Terminal

M107

12

No

2015 Rogue NAM

B2602 SHIFT POSITION

SEC-89

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

Component Inspection

INFOID:0000000011278495

1.

CHECK CVT SHIFT SELECTOR (PARK POSITION SWITCH)

1. Turn ignition switch OFF.

2. Disconnect CVT shift selector connector.

3. Check continuity between CVT shift selector (park position switch) terminals.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace CVT shift selector. Refer to 

TM-193, "Removal and Installation"

.

CVT shift selector (park position switch)

Condition

Continuity

Terminal

12

13

Selector lever

P (Park) position

No

Other than above

Yes

2015 Rogue NAM

SEC-90

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2604 SHIFT POSITION

B2604 SHIFT POSITION

DTC Logic

INFOID:0000000011278496

DTC DETECTION LOGIC

NOTE:

• If DTC B2604 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-64, "DTC Logic"

.

• If DTC B2604 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-65, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Shift the selector lever to the P position.

2. Turn ignition switch ON and wait 5 seconds or more.

3. Shift the selector lever to the N position and wait 5 seconds or more.

4. Shift the selector lever to any position other than P and N, and wait 5 seconds or more.

5. Check DTC in “Self Diagnostic Result” of “BCM” using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-90, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011278497

Regarding Wiring Diagram information, refer to 

SEC-41, "Wiring Diagram"

.

1.

CHECK DTC OF TCM

Check DTC in “Self Diagnostic Result” of “TCM” using CONSULT.
Is DTC detected?

YES

>> Perform the trouble diagnosis related to the detected DTC. Refer to 

TM-63, "DTC Index"

.

NO

>> GO TO 2.

2.

CHECK FUSE

1. Turn power switch OFF.

2. Check that the following fuse in IPDM E/R is not blown.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace the blown fuse after repairing the cause of blowing.

3.

CHECK TRANSMISSION RANGE SWITCH POWER SUPPLY

1. Disconnect transmission range switch connector.

2. Turn ignition switch ON.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B2604

SHIFT PN DIAG CAN

The following states are detected for 5 seconds 
while ignition switch is ON:
• P/N position signal is sent from transmission 

range switch but shift position signal input 
(CAN) from TCM is other than P and N.

• P/N position signal is not sent from transmis-

sion range switch but shift position signal input 
(CAN) from TCM is P or N.

• Harness or connectors

(The CAN communication line is 
open or shorted.)

• Harness or connectors 

(Transmission range switch circuit 
is open or shorted.)

• TCM
• BCM

Signal name

Fuse No.

Ignition power supply

46 (10 A)

2015 Rogue NAM