Nissan Rogue. Manual - part 80

AV-312

< DTC/CIRCUIT DIAGNOSIS >

[NAVIGATION WITH BOSE]

U1232 STEERING ANGLE SENSOR

U1232 STEERING ANGLE SENSOR

DTC Logic

INFOID:0000000011276974

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000011276975

1.

ADJUST PREDICTIVE COURSE LINE CENTER POSITION ADJUSTMENT OF STEERING ANGLE SEN-

SOR
When U1232 is detected, the predictive course line center position of steering angle sensor needs to be

adjusted.

>> Adjust the predictive course line center position of steering angle sensor. Refer to 

AV-284, "PRE-

DICTED COURSE LINE CENTER POSITION ADJUSTMENT : Work Procedure"

.

CONSULT Display

DTC Detection Condition

Possible Cause

ST ANG SEN CALIB
 [U1232]

Predictive course line center position adjustment 
of steering angle sensor is incomplete.

Adjust predictive course line center position ad-
justment of steering angle sensor.

AV

U1244 GPS ANTENNA

AV-313

< DTC/CIRCUIT DIAGNOSIS >

[NAVIGATION WITH BOSE]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

U1244 GPS ANTENNA

DTC Logic

INFOID:0000000011276976

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000011276977

Regarding Wiring Diagram information, refer to 

AV-253, "Wiring Diagram"

.

1.

GPS ANTENNA INSPECTION

Visually inspect the GPS antenna and antenna feeder. Refer to 

AV-384, "Removal and Installation"

.

Is inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace malfunctioning components.

2.

CHECK AV CONTROL UNIT VOLTAGE 

1. Disconnect AV control unit connector M141.

2. Turn ignition switch ON.

3. Check voltage between AV control unit connector M141 and ground.

Is inspection result normal?

YES

>> Replace GPS antenna. Refer to 

AV-384, "Removal and Installation"

.

NO

>> Replace AV control unit. Refer to 

AV-369, "Removal and Installation"

.

CONSULT Display

DTC Detection Condition

Possible Cause

GPS ANTENNA CONN
[U1244]

Open or short to ground is detected in GPS an-
tenna connection.

• GPS antenna disconnection.
• Open or short to ground in GPS antenna signal 

circuit.

AV control unit 

Ground

Voltage

Connector

Terminal

M141

58

—

5.0 V

AV-314

< DTC/CIRCUIT DIAGNOSIS >

[NAVIGATION WITH BOSE]

U1258 SATELLITE RADIO ANTENNA

U1258 SATELLITE RADIO ANTENNA

DTC Logic

INFOID:0000000011276978

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000011276979

Regarding Wiring Diagram information, refer to 

AV-253, "Wiring Diagram"

.

1.

SATELLITE ANTENNA INSPECTION

Visually inspect the satellite antenna and antenna feeder. Refer to 

AV-386, "Feeder Layout"

.

Is inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace malfunctioning components.

2.

CHECK AV CONTROL UNIT VOLTAGE 

1. Turn ignition switch ON.

2. Check voltage between AV control unit connector M142 and ground.

Is inspection result normal?

YES

>> Replace satellite radio antenna 

AV-385, "Removal and Installation"

.

NO

>> Replace AV control unit. Refer to 

AV-369, "Removal and Installation"

.

CONSULT Display

DTC Detection Condition

Possible Cause

SXM ANTENNA CONN
[U1258]

Open or short to ground is detected in satellite 
antenna connection.

• Satellite antenna disconnection.
• Open or short to ground in satellite antenna 

signal circuit.

AV control unit

Ground

Voltage

Connector

Terminal

M142

56

—

5.0 V

AV

U1263 USB

AV-315

< DTC/CIRCUIT DIAGNOSIS >

[NAVIGATION WITH BOSE]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

U1263 USB

DTC Logic

INFOID:0000000011276980

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM SELF DIAGNOSTIC RESULT

1. If there is a device connected to the USB interface, disconnect it.

2. Turn ignition switch ON and wait for 2 seconds or more.

3. Perform “Self Diagnostic Result” for “MULTI AV”. 
Is DTC U1263 displayed?

YES

>> Refer to 

AV-315, "Diagnosis Procedure"

. 

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000011276981

1.

CHECK USB INTERFACE HARNESS

Visually inspect USB interface harness. Refer to 

AV-378, "Removal and Installation"

.

Is the inspection result normal?

YES

>> GO TO 2. 

NO

>> Replace USB interface harness. Refer to 

AV-378, "Removal and Installation"

.

2.

CHECK USB INTERFACE HARNESS

Check USB interface harness. Refer to 

AV-352, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> Replace AV control unit. Refer to 

AV-369, "Removal and Installation"

.

NO

>> Replace USB interface harness. Refer to 

AV-378, "Removal and Installation"

.

CONSULT Display

DTC Detection Condition

Possible Cause

USB OVERCURRENT
[U1263]

Overcurrent in USB harness is detected.

• Device connected to USB interface.
• Harness between the AV control unit and USB 

interface.