Nissan Altima HL32 Hybrid. Manual - part 406

EXL-24

< FUNCTION DIAGNOSIS >

COMBINATION SWITCH

Wiper intermittent dial posi-

tion

Intermittent oper-

ation delay inter-

val

INT VOLUME switch ON/OFF status  

INT VOLUME 1 switch

INT VOLUME 2 switch

INT VOLUME 3 switch

1

Short

↑
↓

Long

ON

ON

ON

2

ON

ON

OFF

3

ON

OFF

OFF

4

OFF

OFF

OFF

5

OFF

OFF

ON

6

OFF

ON

ON

7

OFF

ON

OFF

DIAGNOSIS SYSTEM (BCM)

EXL-25

< FUNCTION DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

DIAGNOSIS SYSTEM (BCM)

COMMON ITEM
COMMON ITEM : Diagnosis Description

INFOID:0000000004501352

BCM CONSULT-III FUNCTION

CONSULT-III performs the following functions via CAN communication with BCM.

SYSTEM APPLICATION

BCM can perform the following functions for each system.

NOTE:

It can perform the diagnosis modes except the following for all sub system selection items.

COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)

INFOID:0000000004501353

ECU IDENTIFICATION

Displays the BCM part No.

SELF-DIAG RESULT

Refer to 

BCS-81, "DTC Index"

.

Diagnosis mode

Function Description

WORK SUPPORT

Changes the setting for each system function.

SELF-DIAG RESULTS

Displays the diagnosis results judged by BCM.

CAN DIAG SUPPORT MNTR

Monitors the reception status of CAN communication viewed from BCM.

DATA MONITOR

The BCM input/output signals are displayed.

ACTIVE TEST

The signals used to activate each device are forcibly supplied from BCM.

ECU IDENTIFICATION

The BCM part number is displayed.

CONFIGURATION

• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.

System

Sub system selection item

Diagnosis mode

WORK SUPPORT

DATA MONITOR

ACTIVE TEST

Door lock

DOOR LOCK

×

×

×

Rear window defogger

REAR DEFOGGER

×

×

Warning chime

BUZZER

×

×

Interior room lamp timer

INT LAMP

×

×

×

Exterior lamp

HEAD LAMP

×

×

×

Wiper and washer

WIPER

×

×

×

Turn signal and hazard warning lamps FLASHER

×

×

×

Air conditioner

AIR CONDITONER

×

Intelligent Key system

INTELLIGENT KEY

×

×

×

Combination switch

COMB SW

×

BCM

BCM

×

Immobilizer

IMMU

×

×

Interior room lamp battery saver

BATTERY SAVER

×

×

×

Trunk open

TRUNK

×

Vehicle security system

THEFT ALM

×

×

×

RAP system

RETAINED PWR

×

Signal buffer system

SIGNAL BUFFER

×

×

TPMS

AIR PRESSURE MONITOR

×

×

×

EXL-26

< FUNCTION DIAGNOSIS >

DIAGNOSIS SYSTEM (BCM)

HEADLAMP
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)

INFOID:0000000004501355

WORK SUPPORT

1 : Initial setting
2 : With auto light system

DATA MONITOR

Work item

Setting item

Setting

BATTERY SAVER SET

ON

1

With the exterior lamp battery saver function

OFF

Without the exterior lamp battery saver function

ILL DELAY SET

2

MODE 1

1

45 sec.

Sets delay timer function timer operation time
(All doors closed)

MODE 2

Without the func-
tion

MODE 3

30 sec.

MODE 4

60 sec.

MODE 5

90 sec.

MODE 6

120 sec.

MODE 7

150 sec.

MODE 8

180 sec.

CUSTOM A/LIGHT 
SETTING

2

MODE 1

1

Normal

MODE 2

More sensitive setting than normal setting (Turns ON earlier than normal operation.)

MODE 3

More sensitive setting than MODE 2 (Turns ON earlier than MODE 2.)

MODE 4

Less sensitive setting than normal setting (Turns ON later than normal operation.)

Monitor item

[Unit]

Description

PUSH SW
[ON/OFF]

The switch status input from push-button ignition switch

ENGINE STATE
[STOP/STALL/CRANK/RUN]

The engine status received from ECM with CAN communication

VEH SPEED 1
[km/h]

The value of the vehicle speed received from combination meter with CAN commu-
nication

KEY SW-SLOT
[ON/OFF]

Key switch status input from key slot

DIAGNOSIS SYSTEM (BCM)

EXL-27

< FUNCTION DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

1: The item is indicated, not monitored
2: With auto light system

ACTIVE TEST

TURN SIGNAL R
[ON/OFF]

Each switch status that BCM judges from the combination switch reading function

TURN SIGNAL L
[ON/OFF]

TAIL LAMP SW
[ON/OFF]

HI BEAM SW
[ON/OFF]

HEAD LAMP SW1
[ON/OFF]

HEAD LAMP SW2
[ON/OFF]

PASSING SW
[ON/OFF]

AUTO LIGHT SW
[ON/OFF]

FR FOG SW
[ON/OFF]

DOOR SW-DR
[ON/OFF]

The switch status input from front door switch LH

DOOR SW-AS
[ON/OFF]

The switch status input from front door switch RH

DOOR SW-RR
[ON/OFF]

The switch status input from rear door switch RH

DOOR SW- RL
[ON/OFF]

The switch status input from rear door switch LH

DOOR SW-BK

1

[ON/OFF]

—

OPTICAL (LIGHT) SENSOR
[V]

2

The value of exterior brightness voltage input from the optical sensor 

Monitor item

[Unit]

Description

Test item

Operation

Description

TAIL LAMP

ON

Transmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON.

OFF

Stops the tail lamp request signal transmission.

HEAD LAMP

HI

Transmits the high beam request signal with CAN communication to turn 
the headlamp (HI)

LO

Transmits the low beam request signal with CAN communication to turn 
the headlamp (LO).

OFF

Stops the high & low beam request signal transmission.

FR FOG LAMP

ON

Transmits the front fog lamp light request signal to IPDM E/R with CAN 
communication to turn the front fog lamp ON.

OFF

Stops the front fog lamp request signal transmission.

DAYTIME RUNNING LIGHT

1

ON

Transmits the daytime running light system request signal to IPDM E/R

OFF

Stops the daytime running light request signal transmission