Nissan Altima HL32 Hybrid. Manual - part 371

EC-468

< ON-VEHICLE REPAIR >

[QR25DE]

EVAP CANISTER

ON-VEHICLE REPAIR

EVAP CANISTER

Exploded View

INFOID:0000000004211676

Removal and Installation

INFOID:0000000004211677

REMOVAL

1. Lift up the vehicle.
2. Remove EVAP canister fixing bolt.
3. Remove EVAP canister.
NOTE:

The EVAP canister vent control valve and EVAP canister system pressure sensor can be removed without

removing the EVAP canister.

INSTALLATION

Install in the reverse order of removal.

NOTE:

Tighten EVAP canister fixing bolt to the specified torque.

DISASSEMBLY

1. Turn EVAP canister vent control valve counterclockwise.

2. Remove the EVAP canister vent control valve.

1.

EVAP control system pressure sen-
sor

2.

EVAP canister (MAIN)

3.

Bolt

4.

Hose

5.

O-ring

6.

EVAP canister vent control valve

7.

EVAP canister (SUB)

ALBIA0170GB

A

:  Lock

B

:  Unlock

ALBIA0156ZZ

EVAP CANISTER

EC-469

< ON-VEHICLE REPAIR >

[QR25DE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

ASSEMBLY

Assemble in the reverse order of disassembly.

CAUTION:

Always replace O-ring with a new one.

Inspection

INFOID:0000000004211678

Check EVAP canister as follows:
1. Block port (B).
2. Blow air into port (A) and check that it flows freely out of port (C).
3. Release blocked port (B).
4. Apply vacuum pressure to port (B) and check that vacuum pres-

sure exists at the ports (A) and (C). 

5. Block port (A) and (B).
6. Apply pressure to port (C) and check that there is no leakage.

ALBIA0154ZZ

EC-470

< SERVICE DATA AND SPECIFICATIONS (SDS) 

[QR25DE]

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

Idle Speed

INFOID:0000000004211679

Ignition Timing

INFOID:0000000004211680

Calculated Load Value

INFOID:0000000004211681

Mass Air Flow Sensor

INFOID:0000000004211682

*: Engine is warmed up to normal operating temperature and running under no load.

Condition

Specification

No load (in N position)

1,000 

± 50 rpm

Condition

Specification

No load (in N position)

21 

± 5° BTDC

Condition

Specification (Using CONSULT-III or GST)

At idle

10 – 35 %

At 2,500 rpm

10 – 35 %

Supply voltage

Battery voltage (11 – 14 V)

Output voltage at idle (in N position)

0.9 – 1.2 V*

Mass air flow (Using CONSULT-III or GST)

1.0 – 5.0 g·m/sec at idle*

4.0 – 12.0 g·m/sec at 2,500 rpm*

EM-1

ENGINE

C

D

E

F

G

H

I

J

K

L

M

SECTION 

EM

A

EM

N

O

P

CONTENTS

ENGINE MECHANICAL

QR25DE

PRECAUTION ...............................................

3

PRECAUTIONS ...................................................

3

Precaution for Supplemental Restraint System 
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...................................................................

3

Precautions For High-Voltage System  ......................

3

Necessary for Steering Wheel Rotation After Bat-
tery Disconnect  .........................................................

3

Precaution for Draining Coolant  ................................

3

Precaution for Disconnecting Fuel Piping  .................

4

Precaution for Removal and Disassembly  ................

4

Precaution for Inspection, Repair and Replace-
ment ..........................................................................

4

Precaution for Assembly and Installation  ..................

4

Parts Requiring Angular Tightening ..........................

4

Precaution for Liquid Gasket .....................................

4

PREPARATION ............................................

6

PREPARATION ...................................................

6

Special Service Tool  .................................................

6

Commercial Service Tool  ..........................................

8

FUNCTION DIAGNOSIS ..............................

10

NOISE, VIBRATION, AND HARSHNESS 
(NVH) TROUBLESHOOTING  ............................

10

NVH Troubleshooting - Engine Noise  .....................

10

Use the Chart Below to Help You Find the Cause 
of the Symptom  .......................................................

11

ON-VEHICLE MAINTENANCE ....................

12

SPARK PLUG  ....................................................

12

Removal and Installation .........................................

12

DRIVE BELTS  ....................................................

14

Checking Drive Belts ...............................................

14

Tension Adjustment  ................................................

14

Removal and Installation of Drive Belt .....................

14

Removal and Installation of Drive Belt Auto-ten-
sioner .......................................................................

15

Removal and Installation of Idler Pulley  ..................

16

AIR CLEANER FILTER .....................................

18

Removal and Installation  .........................................

18

CAMSHAFT VALVE CLEARANCE  ..................

19

Camshaft Valve Clearance ......................................

19

COMPRESSION PRESSURE  ...........................

22

Compression Pressure  ............................................

22

ON-VEHICLE REPAIR .................................

24

AIR CLEANER AND AIR DUCT  .......................

24

Removal and Installation  .........................................

24

INTAKE MANIFOLD  .........................................

25

Removal and Installation  .........................................

25

EXHAUST MANIFOLD AND THREE WAY 
CATALYST ........................................................

29

Removal and Installation  .........................................

29

OIL PAN AND OIL STRAINER  .........................

31

Removal and Installation  .........................................

31

IGNITION COIL  .................................................

34

Removal and Installation  .........................................

34

FUEL INJECTOR AND FUEL TUBE  ................

35

Removal and Installation  .........................................

35

ROCKER COVER  .............................................

38

Removal and Installation  .........................................

38

CAMSHAFT .......................................................

40

Removal and Installation  .........................................

40

Inspection After Installation  .....................................

47

Valve Clearance  ......................................................

48