Nissan Sentra. Manual - part 774

 

  Index      Nissan     Nissan Sentra (2014 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

  

 

Content   ..  772  773  774  775   ..

 

 

Nissan Sentra. Manual - part 774

 

 

SEC-124

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B210C STARTER CONTROL RELAY

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-30, "Removal and Installation"

.

NO

>> GO TO 3.

3.

CHECK STARTER CONTROL RELAY CONTROL CIRCUIT CONTINUITY

1. Disconnect IPDM E/R connector E46 and BCM connector M83.

2. Check continuity between IPDM E/R connector E46 and BCM connector M83.

3. Check continuity between IPDM E/R connector E46 and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-73, "Removal and Installation"

.

NO

>> Repair or replace harness or connectors.

IPDM E/R

BCM

Continuity

Connector

Terminal

Connector

Terminal

E46

44

M83

74

Yes

IPDM E/R

Ground

Continuity

Connector

Terminal

E46

44

—

No

B210D STARTER RELAY

SEC-125

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B210D STARTER RELAY

DTC Logic

INFOID:0000000009756778

DTC DETECTION LOGIC

NOTE:

If DTC B210D is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to 

BCS-

63, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Press push-button ignition switch under the following conditions to start engine, and wait 1 second or

more.

CVT models

-

CVT selector lever is in the P (Park) or N (Neutral) position

-

Do not depress the brake pedal

M/T models

-

Shift lever: in the neutral position

-

Clutch pedal: Not depressed

2. Check DTC in Self Diagnostic Result mode of IPDM E/R using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-125, "Diagnosis Procedure"

.

NO

>> Inspection End

Diagnosis Procedure

INFOID:0000000009756779

Regarding Wiring Diagram information, refer to 

SEC-25, "Wiring Diagram"

.

1.

 PERFORM SELF DIAGNOSTIC RESULT

Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is display history of DTC B210D CRNT?

YES

>> GO TO 2.

NO

>> Refer to 

GI-39, "Intermittent Incident"

.

2.

CHECK STARTER CONTROL RELAY CONTROL CIRCUITS VOLTAGE

Check voltage between IPDM E/R connectors and ground.

Is the inspection result normal?

DTC No.

Trouble diagnosis 

name

DTC detecting condition

Possible cause

B210D

STARTER RELAY 
ON CIRC

When comparing the following items, IPDM E/R de-
tects that starter control relay is stuck in the ON po-
sition for 5 second or more.
• Starter control relay signal (CAN) from BCM
• Starter relay status signal (CAN) from BCM
• Starter control relay and starter relay status sig-

nal (IPDM E/R input)

• Starter control relay control signal (IPDM E/R 

output)

• Harness or connectors (starter mo-

tor relay control circuit open or 
short)

• IPDM  E/R
• BCM

IPDM E/R

Ground

Voltage

(Approx.)

Connector

Terminal

E46

44

—

Battery voltage

SEC-126

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B210D STARTER RELAY

YES

>> Replace IPDM E/R. Refer to 

PCS-30, "Removal and Installation"

.

NO

>> GO TO 3.

3.

CHECK STARTER CONTROL RELAY CONTROL CIRCUIT CONTINUITY

1. Disconnect IPDM E/R connectors E46 and BCM connector M83.

2. Check continuity between IPDM E/R connector E46 and ground.

Is the inspection result normal?

YES

>> Refer to 

SEC-95, "Diagnosis Procedure"

.

NO

>> Repair or replace harness or connectors.

IPDM E/R

Ground

Continuity

Connector

Terminal

E46

44

—

No

B210E STARTER RELAY

SEC-127

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B210E STARTER RELAY

DTC Logic

INFOID:0000000009756780

DTC DETECTION LOGIC

NOTE:

• If DTC B210E is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

PCS-26, "DTC Logic"

.

• If DTC B210E is displayed with DTC B2605, first perform the trouble diagnosis for DTC B2605. Refer to

SEC-93, "DTC Logic"

.

• When IPDM E/R power supply voltage is low (Approx. 7 - 8 V for about 1 second), the DTC B210F may be

detected.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Press push-button ignition switch under the following conditions to start engine, and wait 1 second or

more.

CVT models

-

CVT selector lever is in the P (Park) or N (Neutral) position

-

Do not depress the brake pedal

M/T models

-

Shift lever: in the neutral position

-

Clutch pedal: Not depressed

2. Check DTC in Self Diagnostic Result mode of IPDM E/R using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-127, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000009756781

Regarding Wiring Diagram information, refer to 

SEC-25, "Wiring Diagram"

.

1.

 PERFORM SELF DIAGNOSTIC RESULT

Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is display history of DTC B210E CRNT?

YES

>> GO TO 2.

NO

>> Refer to 

GI-39, "Intermittent Incident"

.

2.

CHECK STARTER CONTROL RELAY CONTROL CIRCUITS VOLTAGE

Check voltage between IPDM E/R connectors and ground.

DTC No.

Trouble diagnosis 

name

DTC detecting condition

Possible cause

B210E

STARTER RELAY 
OFF

When comparing the following items, IPDM E/R de-
tects that starter control relay is stuck in the OFF po-
sition for 5 second or more.
• Starter control relay signal (CAN) from BCM
• Starter relay status signal (CAN) from BCM
• Starter control relay and starter relay status signal 

(IPDM E/R input)

• Starter control relay control signal (IPDM E/R out-

put)

• IPDM E/R
• BCM
• Battery

 

 

 

 

 

 

 

Content   ..  772  773  774  775   ..