Nissan Sentra. Manual - part 434

 

  Index      Nissan     Nissan Sentra (2014 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

  

 

Content   ..  432  433  434  435   ..

 

 

Nissan Sentra. Manual - part 434

 

 

EC-432

< DTC/CIRCUIT DIAGNOSIS >

[MRA8DE]

P2122, P2123 APP SENSOR

P2122, P2123 APP SENSOR

DTC Logic

INFOID:0000000009758689

DTC DETECTION LOGIC

NOTE:

If DTC P2122 or P2123 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.

Refer to 

EC-353, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure

before conducting the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Start engine and let it idle for 1 second.

2. Check DTC.
Is DTC detected?

YES

>> Proceed to 

EC-432, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009758690

1.

CHECK APP SENSOR 1 POWER SUPPLY

1. Turn ignition switch OFF.

2. Disconnect accelerator pedal position (APP) sensor harness connector.

3. Turn ignition switch ON.

4. Check the voltage between APP sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

DTC No.

CONSULT screen terms

(Trouble diagnosis con-

tent)

DTC detecting condition

Possible cause

P2122

APP SEN 1/CIRC
(Throttle/Pedal position 
sensor/switch “D” circuit 
low)

An excessively low voltage from the APP 
sensor 1 is sent to ECM.

• Harness or connectors

(APP sensor 1 circuit is open or shorted.)

• Accelerator pedal position sensor (APP 

sensor 1)

P2123

APP SEN 1/CIRC
(Throttle/Pedal position 
sensor/switch “D” circuit 
high)

An excessively high voltage from the APP 
sensor 1 is sent to ECM.

+

−

Voltage

(Approx.)

APP sensor

Connector

Terminal

E12

4

Ground

5.0 V

P2122, P2123 APP SENSOR

EC-433

< DTC/CIRCUIT DIAGNOSIS >

[MRA8DE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

2.

CHECK APP SENSOR 1 POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between APP sensor harness connector and ECM harness connector.

4. Also check harness for short to ground.
Is the inspection result normal?

YES

>> Perform the trouble diagnosis for power supply circuit.

NO

>> Repair or replace error-detected parts.

3.

CHECK APP SENSOR 1 GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between APP sensor harness connector and ECM harness connector.

4. Also check harness for short to power.
Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace error-detected parts.

4.

CHECK APP SENSOR 1 INPUT SIGNAL CIRCUIT

1. Check the continuity between APP sensor harness connector and ECM harness connector.

2. Also check harness for short to ground and to power.
Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace error-detected parts.

5.

CHECK APP SENSOR

Check APP sensor. Refer to 

EC-433, "Component Inspection (APP Sensor)"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

NO

>> Replace accelerator pedal assembly. Refer to 

ACC-3, "Removal and Installation"

.

Component Inspection (APP Sensor)

INFOID:0000000009758691

1.

CHECK ACCELERATOR PEDAL POSITION SENSOR

1. Turn ignition switch OFF.

2. Reconnect all harness connectors disconnected.

3. Turn ignition switch ON.

+

−

Continuity

APP sensor

ECM

Connector

Terminal

Connector

Terminal

E12

4

E16

122

Existed

+

−

Continuity

APP sensor

ECM

Connector

Terminal

Connector

Terminal

E12

2

E16

127

Existed

+

−

Continuity

APP sensor

ECM

Connector

Terminal

Connector

Terminal

E12

3

E16

126

Existed

EC-434

< DTC/CIRCUIT DIAGNOSIS >

[MRA8DE]

P2122, P2123 APP SENSOR

4. Check the voltage between ECM harness connector terminals as per the following condition.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace accelerator pedal assembly. Refer to 

ACC-3, "Removal and Installation"

.

ECM

Condition

Voltage

Connector

+

−

Terminal

E16

126

127

Accelerator pedal

Fully released

0.6 - 0.9 V

Fully depressed

3.9 - 4.7 V

119

120

Fully released

0.3 - 0.6 V

Fully depressed

1.95 - 2.4 V

P2127, P2128 APP SENSOR

EC-435

< DTC/CIRCUIT DIAGNOSIS >

[MRA8DE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

P2127, P2128 APP SENSOR

DTC Logic

INFOID:0000000009758692

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure

before conducting the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Start engine and let it idle for 1 second.

2. Check DTC.
Is DTC detected?

YES

>> Proceed to 

EC-435, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009758693

1.

CHECK APP SENSOR 2 POWER SUPPLY

1. Turn ignition switch OFF.

2. Disconnect accelerator pedal position (APP) sensor harness connector.

3. Turn ignition switch ON.

4. Check the voltage between APP sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK SENSOR POWER SUPPLY 2 CIRCUIT

Check sensor power supply 2 circuit. Refer to 

EC-444, "Diagnosis Procedure"

.

DTC No.

CONSULT screen terms

(Trouble diagnosis con-

tent)

DTC detecting condition

Possible cause

P2127

APP SEN 2/CIRC
(Throttle/Pedal position 
sensor/switch “E” circuit 
low)

An excessively low voltage from the APP 
sensor 2 is sent to ECM.

• Harness or connectors

(APP sensor 2 circuit is open or shorted.)

• Accelerator pedal position sensor

(APP sensor 2)

• Sensor power supply 2 circuit

P2128

APP SEN 2/CIRC
(Throttle/Pedal position 
sensor/switch “E” circuit 
high)

An excessively high voltage from the APP 
sensor 2 is sent to ECM.

+

−

Voltage

(Approx.)

APP sensor

Connector

Terminal

E12

5

Ground

5.0 V

 

 

 

 

 

 

 

Content   ..  432  433  434  435   ..